• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 2002.10b
• /
• pp.201-202
• /
• 2002

The abrasive wear behaviour of $Al_2O_3$ particle-reinforced aluminium composite was investigated. The wear rate of the composite and the matrix alloy has been expressed in terms of the applied load, sliding distance and particle size using linear factorial design approach.

• Tribology and Lubricants
• /
• v.13 no.3
• /
• pp.108-114
• /
• 1997

The electrical and frictional properties of new sintered-metal bearing (S-bearing) with varying loads and speeds were measured. Also those were compared with the same products(J-bearing) made in Japan and the conventionally used ball bearing. The test results show that the frictional values of S-bearing are less than those of J-bearing, and that S-bearing operates in full-hydrodynamic lubrication regime. The values of rating current, starting time and jitter reveal that S-bearing is superior to J-bearing as well as ball bearing.

• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 2002.10b
• /
• pp.139-140
• /
• 2002

This paper discusses the effect of plating condition on the mechanical property of electroplated Cu film. Current density, the amount of the organic additives was found to affect the residual stress of electroplated copper film. The result show that, in the case of residual stress, the copper film deposited at higher additive result in lower residual stress and plating current by $15mA/cm^2$ induced a better result than any other ones.

• Tribology and Lubricants
• /
• v.11 no.1
• /
• pp.50-57
• /
• 1995

When engine oil is used under severe running condition, the Lubricational characteristics is very important. I have studied the Lubricational characteristics with Compound Additives of engine oil for the Falex wear test machine. Adding detergent (Ca-phenate) to engine oil, the seizure is more improved than in case of non-adding, and adding Zn-DTP (Zinc dialkyl dithio phosphate), the extreme pressure property is excellent at the high load. But when the PTFE (Polytetra Fluoro Ethylene) and MoS$_{2}$ (Molybdenum disulfide) are added, the temperature characteristics and the anti-wear property become excellent because the stability can be maintained in a high temperature. The result are as follows, it can be improved that when the compound of the Ca-phenate and Zn-DTP, MoS$_{2}$, PTFE, etc. was added to engine oil, the lubrication characteristics become better. It is argued that it is improved because of excellence of the anti-wear, the extreame pressure properties and the heat stability.

• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 2001.06a
• /
• pp.49-54
• /
• 2001

Monolayers such as self-assembled monolayer (SAM) have received considerable attention to reduce stiction and friction in micro-devices and microelectromechanical systems (MEMS). Various organic molecular films were investigated to obtain better understanding of their tribological behaviors and adhesion property. The organic molecular films studied in this work are: epoxysilane SAMs, octadecyltricholosilane (OST), multi-layers composed of epoxysilane SAMs, poly〔styrene-b-(ethylene-co-butylene)-b-styrene〕(SEBS) and compound of epoxy resin and poly (paraphenylene) (EP/PPP). The pull-off forces of these films were also obtained from force-distance curves measured in static mode of operation of atomic force microscope (AFM). Tribological tests were conducted with a ball-on-flat reciprocating friction tester. The OST showed the lowest pull-off force, indicating its low adhesion property. It was revealed that, the OST, EP/PPP and the multi-layer of epoxysilane SAMs, SEBS and EP/PPP exhibited good tribological properties at the lower load (0.3 N) whereas the OST showed best performance at the higher load (1.8 N).

• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 2002.10b
• /
• pp.187-188
• /
• 2002

Rubber has large differences in elastic characteristics from the other solid materials such as metals. Firstly, the rubber exhibits considerably large elastic compliance. Second is highly non-linear elasticity in which the compliance decreases with increase in strain. The main objective in this research is to reveal the dependence of rubber friction upon these elastic characteristics of the rubber in detail. A super elastic FEM analysis is carried out with using an elastic property of practical rubber. From the calculated result, it is cleared that the rubber makes large real contacting area easier than the metals.

• Tribology and Lubricants
• /
• v.28 no.2
• /
• pp.81-92
• /
• 2012

To product multi-grade oil like engine oil, a sort of mineral base oil is mixed with a fundamental additive liquid package and a polymer liquid as viscosity index improver in order to improve the lubricating property of oil. That is, engine oil is the mixture of more than two fluids. In this paper, it will be systematically organized the governing equation describing non-Newtonian thermo-hydrodynamic lubrication related with the mixture of incompressible fluids based on the principle of continuum mechanics. Then, in order to find how the thermal analysis effect on the bearing performance lubricated with the mixture of multi-fluids, it will be compared to the performances between the mixture of each liquid to be blended and multi-grade engine oil as a single fluid in a high speed journal bearing. It is found that, in the case of lower viscosity oil, the difference of pressure distribution between the above two cases turns out to be existed, even if the load capacity is same level.

• Journal of Institute of Convergence Technology
• /
• v.3 no.1
• /
• pp.15-18
• /
• 2013

The next generation alternative fuel of diesel, DME (Dimethyl Ether) discharges particulate matter hardly due to chemical structural as oxygen-fuel so it has the eco-friendly property. Despite these advantages, the DME has the technical difficulties to apply to the diesel engine because of a low calorific value, viscosity and compressibility effects. From this point of view, we performed experimental studies on improved reliability of DME common-rail vehicle and lubricity enhancement of DME fuel for empirical distribution of eco-friendly DME fuel. Also we analyzed solubility of lubrication enhancer according to a drop in temperature, try to secure reliability about core parts of DME vehicle by applying lubrication enhancer in the DME common-rail vehicle.

• Journal of computational fluids engineering
• /
• v.20 no.4
• /
• pp.109-115
• /
• 2015

In this study, the Stokes flow in the microchannel is analysed where the semicircular protuberances with constant spacing are attached on the upper and lower walls with staggered arrangement. For the low Reynolds number flow in microchannel, Stokes approximation is used and the periodicity and symmetry of the flow are considered to determine the stream function and pressure distribution in the flow field by using the method of least squared error. As results, the streamline patterns and pressure distributions in the flow field are shown for some specific values of the size and spacing of the protuberances, and shear stress distributions on the surface of semicircular protuberances are plotted. Especially, for an important physical property, the average pressure gradient along the microchannel is obtained and compared with that for the case of in-phase arrangement of the upper and lower protuberances. And, for the small clearance between the protuberances of upper and lower walls or between the protuberances and the opposite wall, the average pressure gradient is derived from the lubrication theory and compared with that of the present study.

• Journal of the Korean Society for Precision Engineering
• /
• v.20 no.4
• /
• pp.128-135
• /
• 2003

To decrease environmental damage, the development of environmental friendly fluids provides attractive alternative to the conventional fluids. In this study, the effects of harmful ingredients (Cl, S) contained in the fluids that used in grinding and cutting processes to influence on the nasal cavities of the white rats were measured indirectly. Also, the level of the environmental influence in workshops was graded through analyzing the concentration and chemical ingredients of flying-dust, which generated from the friction and combustion in the cutting process, that for analyzing how harmful the influence of particles to workers then it could be used as the basic data for improving the environment. To improve the conventional machining fluid, which can be harmful on worker's bodies and the environment, the environmental friendly machining method was suggested through analyzing each lubrication properties of vegetable fluid and used-edible oil as alternative fluid. As a result, it was known that an emulsion type fluid might be the main cause leading to some respiratory ailments. Also this paper presents the possibility to use vegetable fluid and used-edible oil as the alternative of cutting fluids.