• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 2000.06a
• /
• pp.126-133
• /
• 2000

A computer program for the analysis of engine lubrication systems has been developed. And a case study of a four cylinders gasoline engine is illustrated. This paper gives the mathematical models for oil flow through hydraulic tappet as well as the ones of oil jet and plain journal bearings. And the new from an oil pump and the flow resistance through an oil filter is considered at various temperatures. In the analysis, the various design guidelines are applied. The distribution of flow and pressure of an engine lubrication system are calculated, and the pressure data compared with the experimental data at a few points in the engine lubrication system. This method is helpful to design of engine lubrication system efficiently.

• Tribology and Lubricants
• /
• v.12 no.4
• /
• pp.43-51
• /
• 1996

Rapid increase of refrigeration & air-conditioning system (r & a system) in modem industries brings attention to the urgency of research & development as a core technology in the area. And it is required to the compatibility problem of r & a system to alternative refrigerant for the protection of environment. Then, it is requested to study the lubrication characteristics of refrigerant compressor which is the core technology in the r & a system. The study of lubrication characteristics in the critical sliding component is essential for the design of refrigerant compressor. Therefore, theoretical investigation of the lubrication characteristics of rotary compressor for r & a system is studied. The Runge-Kutta method is used for the analysis of the behavior of rolling piston in the rotary compressor. The results show that the rotating speed of shaft and the discharge pressure have an important effect upon the angular velocity of the rolling piston. This results give important basic data for the further lubrication analysis and design of the rotary compressor.

• Tribology and Lubricants
• /
• v.15 no.3
• /
• pp.248-256
• /
• 1999

Many tribological components in automobile engine undergo high load and sliding speed with thin film thickness. The lubrication characteristics of the components are regarded as ether hydrodynamic lubrication or boundary lubrication, whereas in a working cycle they actually have both characteristics. Many modem engine lubricants have various additives for better performance which make boundary film formation even under hydrodynamic lubrication regime. Conventional Reynolds equation with the viewpoints of continuum mechanics concerns only bulk viscosity of lubricant, which means that its simulation does not give insights on boundary lubrication characteristics. However, many additives of modern engine lubricant provide mixed modes of boundary lubrication characteristics and hydrodynamic lubrication. Especially, high molecular weight polymeric viscosity index improvers form boundary film on the solid surface and cause non-Newtonian fluid effect of shear thinning. This study has performed the investigation about journal bearing system with the mixed concepts of boundary lubrication and hydrodynamic lubrication which happen concurrently in many engine components under the condition of viscosity index improver added.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.10 no.4
• /
• pp.1-6
• /
• 2002

Engine lubrication system is generally affected by vehicle driving conditions, which are composed of acceleration, braking deceleration and accelerating during cornering. The major reason is due to the oil pan system in which oil is directly influenced by inertia farce caused by vehicle driving conditions. Therefore, to confirm safety of engine lubrication system inertia farce effects are also considered in the developing state. For the purpose, we have carried the engine tilting tests using ourselves made test rig. Verifying the test results we also measured the inertia effects on the engine lubrication system using the circular tuning and slalom test with vehicle. Through the comparison study between two kinds of results we obtained that the engine tilting test rig was very useful to confirm the safety evaluation of engine lubrication system.

• Journal of the Korean Society for Precision Engineering
• /
• v.30 no.10
• /
• pp.1041-1049
• /
• 2013

One of the causes of malfunction of commercial vehicle is corrosion or wear. In order to prevent corrosion and wear, lubricants have to be supplied periodically. However, the period of lubrication usually depends on operator's judgment. If the period is too short, excess lubricant will cause pollution and unnecessary expenses, where as long periodic supply of lubricant might cause wear, damage and eventual breakdown. Therefore, an automatic lubrication system with predetermined interval will reduce the excessive supply of lubricating oil and prevent wear and damage. This thesis presents an automatic lubrication system which consists of a lubricant pump and an embedded controller. An automatic lubrication operating algorithm is used to operate the lubricant pump and feedback the pressure status of the system using pressure sensors. The developed system shows an efficient periodic supply of lubricant.

• Tribology and Lubricants
• /
• v.22 no.1
• /
• pp.47-52
• /
• 2006

It is very important to control pressure and flow rate distribution on each component of engine lubrication network. Sometimes many kinds of orifice are used to control flow rate in the hydraulic lubrication field. In this study orifices were adopted on the lubrication network to control oil flow rate distribution. And unsteady transient flow network analysis was carried out to find out the effects of orifices on the engine oil circuit system.

• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 1996.05a
• /
• pp.7-16
• /
• 1996

Rapid increase of refrigeration & air-conditioning system( r & a system ) in modern industries brings attention to the urgency of development as a core technology in the area. And it required to the compatibility problem of r & a system to alternative refrigerant for the protection of environment. Then, it is requested to research about the lubrication characteristics of refrigerant compressor which is the core thechnology in the r & a system. The study of lubrication characteristics in the critical sliding component is essential for the design of refrigerant compressor. Therefore, theoetical investigation of the lubrication characteristics of rotary compressor for r & a system is studied. And the Runge-Kutta method is used for the analysis of the behavior of rolling piston in the rotary compressor. The results show that the rotating speed of shaft and the discharge pressure have an important effect upon the angular velocity of the rolling piston. This results give important basic data for the further lubrication analysis and design of the rotary compressor.

• KSTLE International Journal
• /
• v.1 no.1
• /
• pp.21-28
• /
• 2000

A computer program fur the analysis of engine lubrication systems has been developed. And a case study of a four cylinders gasoline engine is illustrated. This paper gives the mathematical models far oil flow through hydraulic tappet as well as those of oil jet and plain journal bearings. And the flow from an oil pump and the flow resistance through an oil filter is considered at various temperatures. In the analysis, the various design guidelines are applied. The distribution of flow and pressure of an engine lubrication system are calculated, and the pressure data compared with the experimental data at a few points in the engine lubrication system. This method is helpful to design of engine lubrication system efficiently.

• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 2000.11a
• /
• pp.171-176
• /
• 2000

In development process of engine lubrication system, many failure cases are related with aeration problem. Therefore, it is very important to clarify the aeration in the engine oil circuit system. As of today, many factors have been introduced as the major cause in the engine oil aeration. However, still many test data related with those are required to clearly understand it. In this paper the aeration measurement system and calculation method are introduced. And also using this system we measured engine oil aeration fur various cases. From these results some conclusions are reduced.

• Journal of Mechanical Science and Technology
• /
• v.20 no.10
• /
• pp.1716-1721
• /
• 2006

The Lubrication Mode of line contacts between the vane and the camring in an oil hydraulic vane pump has been investigated. First, the variations of the radial force of a vane were calculated from previous measurements of dynamic internal pressure in four chambers surrounding a vane. Next, the lubrication modes were distinguished with Hooke's chart, which is an improvement over Johnson's chart. Finally, the influence of the boundary conditions in the lubrication region on the fluid film lubrication was examined by calculating the film pressure distributions. The results showed that the lubrication mode of the vane tip exists in the rigid-variable-viscosity region, and that discharge pressure higher than 7 MPa greatly affects the oil film pressure in the small and the large arc section because of the Piezo-viscous effect.