• Elastomers and Composites
• /
• 제44권1호
• /
• pp.69-75
• /
• 2009

본 연구에서는 폐윤활유를 이용하여 아스팔트 포장도로의 균열 보수에 주로 사용하는 아스팔트 실란트를 제조하였다. 아스팔트(AP-5), SBS 삼블록 공중합체(triblock copolymer), 점착제(석유수지) 및 산화방지제를 폐윤활유와 혼합하여 콘 침입도, 연화점, 신도, 흐름성, 인장 접착 신율 및 원상회복률을 측정하였다. 폐윤활유 함량이 증가함에 따라 아스팔트 실란트의 콘 침입도는 증가하였고 연화점, 신도 및 원상회복률은 감소하였다. 증량제로 탈크를 첨가할 경우 함량에 비례하여 연화점 및 원상회복률은 증가하였으나 콘 침입도, 신도 및 인장 접착 신율은 감소하였다. 석유수지 함량을 크게 줄여 ASTM 규격에 적합하면서도 가장 경제적인 균열 보수용 아스팔트 실란트를 제조할 수 있었다.

• 한국정밀공학회지
• /
• 제30권10호
• /
• pp.1041-1049
• /
• 2013

One of the causes of malfunction of commercial vehicle is corrosion or wear. In order to prevent corrosion and wear, lubricants have to be supplied periodically. However, the period of lubrication usually depends on operator's judgment. If the period is too short, excess lubricant will cause pollution and unnecessary expenses, where as long periodic supply of lubricant might cause wear, damage and eventual breakdown. Therefore, an automatic lubrication system with predetermined interval will reduce the excessive supply of lubricating oil and prevent wear and damage. This thesis presents an automatic lubrication system which consists of a lubricant pump and an embedded controller. An automatic lubrication operating algorithm is used to operate the lubricant pump and feedback the pressure status of the system using pressure sensors. The developed system shows an efficient periodic supply of lubricant.

• Tribology and Lubricants
• /
• 제10권4호
• /
• pp.75-81
• /
• 1994

In load sharing model, the load is supported by the contacting asperities and the lubricants. The asperity contact area of two sliding surfaces are relatively very small as compared with the apparent contact area. The asperity contact pressure is relatively higher than the lubricant pressure. With the combined effect of asperity and lubricant pressure, the surface roughness and temperature rise must be considered to calculate the lubricant film thickness of the line-contact bearing.

• 소성∙가공
• /
• 제9권4호
• /
• pp.356-361
• /
• 2000

In this study, when a square cup is under drawing, blank holder pressure necessary for flange wrinkling prevention was experimentally studied. The materials used in the experiment were SPCC steel and SUS304 and the drawing ratio was 1.62∼2.0. Two cases for lubricantion condition were investigated. One was without lubricant and the other was with lubricant of high viscosity.

• 한국분말야금학회:학술대회논문집
• /
• 한국분말야금학회 2006년도 Extended Abstracts of 2006 POWDER METALLURGY World Congress Part2
• /
• pp.731-732
• /
• 2006

Recently warm compaction techniques are focused on and commercialization of one high-density compaction process in the P/M industry. Another development is a new SEGLESS using a developed lubricant that reduces ejection force at room temperature compaction. It is possible to achieve high-density by reducing lubricant amount. In this paper we confirmed that green density was $7.35g/cm^3$ at 686MPa of compaction pressure when the new SEGLESS was applied to relatively lower temperature warm compaction process, such as $80^{\circ}C$.

• 한국윤활학회:학술대회논문집
• /
• 한국윤활학회 2002년도 proceedings of the second asia international conference on tribology
• /
• pp.277-278
• /
• 2002

Magnetron and Ion beam sputtering were used to texture the air-bearing surface of magnetic recording sliders. Flying height measurements and Laser-Doppler interferometry were used to compare the 'flyability' of textured and untextured sliders. Lubricant redistribution on the disk surface caused by slider/disk interactions was investigated using scanning ellipsometry (Surface Reflectance Analyzer (SRA)). The results show that slider surface texture causes only small changes in the flying height of sliders but reduces slider in-plane and out-of-plane vibrations. Textured sliders were found to cause less lubricant depletion on the disk surface than untextured sliders.

• 대한기계학회논문집B
• /
• 제21권2호
• /
• pp.224-234
• /
• 1997

It was demonstrated earlier that for laminar, isothermal flow of the lubricant in long journal bearings, inertia has negligible effect on the load carrying capacity and influences only the stability characteristics of the bearing. The question in the present paper is: 'will these conclusions of the isothermal theory remain valid in the presence of significant dissipation, or will lubricant inertia and dissipation interact non-linearly to bring about qualitative changes in bearing performance\ulcorner' The results obtained here assert that the effect of lubricant inertia on load carrying capacity remains negligible, irrespective of the rate of dissipation. The stability of the bearing is, however, affected by lubricant inertia. These results, although obtained here for long bearings with Sommerfeld and Gumbel boundary conditions, are believed to be applicable to practical bearing operations and affirm that bearing load may be calculated from classical, i. e., non-inertial theory.

• 소성∙가공
• /
• 제11권4호
• /
• pp.349-354
• /
• 2002

In order to find the effect of lubricant viscosity, sheet surface roughness, tool geometry, and forming speed on the frictional characteristics in sheet metal forming, a sheet metal friction tester was designed and manufactured and friction test of various sheet were performed. Friction test results showed that as the lubricant viscosity becomes lower, the friction coefficient is higher. When surface roughness is extremely low or high, the friction coefficient is relatively high. The result also show that as the punch radius and punch speed becomes bigger, the friction coefficient is smaller. Using experimental results, the mathematical expression between friction coefficient and lubricant viscosity, surface roughness, punch comer radius, or punch speed is also described.

• Tribology and Lubricants
• /
• 제14권4호
• /
• pp.58-63
• /
• 1998

This paper presents a study of the elastohydrodynamic lubrication of elliptical contacts where lubricant entrainment coincides with the major axis of the Hertzian contact ellipse. A finite difference method and the Newton-Raphson method are applied to analyze the problem. Film contours and pressure distributions are compared with the results for lubricant entrainment coincides with the minor axis. Variations of the minimum and central film thicknesses with the radius ratio are also examined. The results showed that the present numerical scheme can be used generally in the analysis of the EHL of elliptical contacts where the lubricant entraining vector did not coincide with either of the principal axis of the conjunction.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2001년도 춘계학술대회 논문집
• /
• pp.24-27
• /
• 2001

Friction between the sheet and tools is one of the important factors affecting the sheet metal forming. Therefore, the clarification of the friction is essential to improve the formability of the sheet. In order to find the effect of material property and lubricant viscosity on the frictional characteristics, tensile test, surface roughness test and friction test are performed. The results showed that friction characteristics are mainly influenced by the surface roughness and lubricant viscosity. A mathematical model of the friction is developed for calculating friction coefficient in terms of surface roughness and lubricant viscosity. The validity and accuracy of the mathematical model of the friction are verified through the experiment and FEM analysis.