• Journal of IKEEE
• /
• v.22 no.3
• /
• pp.862-865
• /
• 2018

The proposed scheme minimizes the Idle time under the residual energy of the sensor node to adjust the Sleep-Wakeup period and minimize unnecessary energy consumption. It is The proposed scheme minimizes the Idle time under the residual energy of the sensor node to adjust the Sleep-Wakeup period and minimize unnecessary energy consumption. It is an important process to control the Application Packet Framework including the PHY and the MAC layer at each node's Idle time with the Idle time mechanism state before the proposed function is executed. The Current Control Level of the Report Attribute is fixed at one sending / receiving node where power consumption can occur, by changing Sleep-Wakeup time, the low power consumption efficiency was improved while satisfying the transmission requirement of the given delay time constraint.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.9 no.9
• /
• pp.971-976
• /
• 2014

In this paper, we proposed a low power algorithm using state transition ready method. The proposed algorithm defined a sleep state, a idle state and a run state for the task. A state transition occurring at the time due to the delay time created in order to reduce the power consumption state in the middle of each inserted into the ready state. The ready state considering a power consumption and a delay time in state transition. A scheduling step of performing the steps in excess of the increasing problems have the delay time is long. The power consumption increased for the operation step increase. A state transition from a sleep state with the longest delay time in operating state occurs when the state is switched by the time delay caused by the increase in operating time reduces the overall power consumption reduced. Experiments [6] were compared with the results of the power consumption. The experimental results [6] is reduced power consumption than the efficiency of the algorithm has been demonstrated.

• Journal of ILASS-Korea
• /
• v.23 no.3
• /
• pp.128-135
• /
• 2018

In this study, the following conclusions could be obtained from the analysis of emissions contribution rates and features for contaminated emissions by 13,456 gasoline vehicles passed in the vehicle load test (ASM-idle) under the inspection year 2013 to 2017. It was confirmed that the contamination of the CO, HC, NOx by the displacement is reduced on over 3L engine. As a result of comparing the exhaust gas in the low speed idle mode and the AS2525 mode, the exhaust gas in the low speed idle mode was measured high. It is estimated that if ISG function is applied, emissions from idle condition will be reduced. NOx emissions were reduced when the engine power was above 200HP. It has been confirmed that the amount of exhaust emissions are significantly reduced for vehicles manufactured after 2004. As a result of analyzing the exhaust gas according to the season, it is judged that there is a correlation between HC and NOx according to the ambient temperature. The concentration of exhaust emission in vehicles with high accumulated distance increases, which is considered to be the result of aging of the vehicle.

• Proceedings of the KIPE Conference
• /
• 2011.07a
• /
• pp.280-282
• /
• 2011

This paper presents a development of voltage compensation dc/dc converter to decrease fuel consumption of RTGC system. We used 3-phase interleaved converter, which has the same structure as the commercially available three-phase inverter, is used. RTGC system is supplied the power from diesel-engine generator. According to power demand, engine speed is varying 20~60Hz, and voltage is varying 210Vac ~ 480Vac. When idle mode or low power operation dc/dc converter operates by constant output voltage control. The perpormance of converter is evaluated through several experiments with a real RTGC. Proposed system can cut down fuel consumption by 36% at idle mode operation.

• Journal of Electrical Engineering and Technology
• /
• v.8 no.1
• /
• pp.137-143
• /
• 2013

This paper presents development of variable speed generation (VSG) system with energy saving function. The rubber tyred gantry crane (RTGC) requires the power from diesel-engine. Significant fuel savings by reducing the engine speed can be achieved, because all of operation modes except hoisting are required lower power than rated value of engine. When low speed operation output voltage of generator is decrease until acceptable range of motor driver inverters and auxiliary load supplier. According to power demand engine speed is varying from 20 to 60Hz, and voltage is varying between 210Vac and 480Vac. When idle mode or low power operation dc/dc converter operates by constant output voltage control and inverters dc site voltage is compensated by it. This paper proposed 3-phase interleaved boost converter which has the same structure as the commercially available 3-phase inverter and current sharing capability. 400kW interleaved converter is designed and a performance of converter is evaluated through several experiments with a RTGC system. Energy saving VSG system can cut down fuel consumption by 36% and 21.3% at idle and unidirectional load operations.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.46 no.10
• /
• pp.53-60
• /
• 2009

Due to increased integration density and reduced threshold voltages, leakage current reduction becomes important in the semiconductor IC design for low power consumption. In a combinational logic circuit, the leakage current in the standby state depends on the values of the input. In this research, we developed a new input vector control method to minimize the leakage power. A new efficient algorithm is developed to find the minimal leakage vector. It can reduce the leakage current by 15.7% from the average leakage current and by 6.7% from the results of simulated evolution method during standby or idle states for a set of benchmark circuits. The minimal leakage input vector, with idle input signal, can also reduce the leakage current by 6.8% from the average leakage current and by 3.2% from the results of simulated evolution method for sequential circuits.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.5 no.3
• /
• pp.27-34
• /
• 1997

The effects of the intake and exhaust valve timing to improve the engine performance in a spark ignition 3-cylinder LPG engine with a closed loop fuel supply system were studied. The engine torque and power have been measured using the 75kW EC-dynamometer while adjusting the optimal fuel consumption ratio with a solen- oid driver. As the results from this experiment, when intake valve opening is $12^{\circ}$ BTDC, intake valve closing is $36^{\circ}$ ABDC, exhaust valve opening is $12^{\circ}$ ATDC, and exhaust valve closing is $36^{\circ}$ BBDC respectively, the best torque characteristics in low and high speeds for a gives engine were obtained. And also we could find that the torque characteristics in low speeds were affected by the timing of exhaust valve open. An increased valve overlap by the EVC delay was ineffectual to the torque characte- ristics improvement in high speeds.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.49 no.10
• /
• pp.34-42
• /
• 2012

This paper analyses the energy saving basic power models in core IP networks, and proposes the adaptive buffer and burst scheme which is a possible energy saving method, and its implementation algorithm in core IP networks. Especially this paper describes the adaptive buffer and burst scheme dynamically varying the buffering interval B according to the input traffic volume of ingress router, and explains the operation principle of proposed scheme. This method is to adjust the buffering interval B according to input traffic volume of ingress router, that is increasing the interval B when input traffic volume is low, and decreasing the interval B when input traffic volume is high between some given interval regions. This method can gets the high energy saving effect as decreasing the transition number of idle/active in networks when input traffic volume is low, and decreasing the transition number of idle/active by the continuous of burst packets in transit router when input traffic volume is high. This paper shows the increasing of asleep rate for the energy saving of core IP networks and confirms the energy saving of core IP networks by the computer simulation. We confirmed that proposed method can be save the energy of IP networks by properly trade off network performances.

• Asia-Pacific Journal of Business
• /
• v.13 no.2
• /
• pp.139-154
• /
• 2022

Purpose - This study aims to analyzing of solar power generation cost-benefit. Design/methodology/approach - We analyzed whether there is economic feasibility by selecting parking lots and idle sites located in four areas of Seoul, Gyeonggi, Chungcheong, Jeolla, and Gyeongsang areas nationwide, and analyzing site conditions and installation capacity. Findings - According to the results of the analysis, it was found that there is low profitability in Seoul, Gyeonggi and Chungcheong regions, where the solar radiation was not excellent even if REC is selected through the contract market. However, it is necessary to analyzed the economical validity the profitable validity including environmental benefits (greenhouse gas reduction, NOx, SOx reduction effect) and social benefits (renewable power supply) that is analyzed by income and operating costs which is occurred from electricity sales and REC sales when installing solar power generation facilities. Research implications or Originality - In this study, economic feasibility was evaluated additionally in consideration of environmental and social benefits. In conclusion, it was shown that businesses are not economical when considering only simple financial aspects are also sufficiently economical when it is considering environmental and social benefits.

• KSII Transactions on Internet and Information Systems (TIIS)
• /
• v.11 no.3
• /
• pp.1393-1405
• /
• 2017

It is well known that duty-cycling control by dynamically adjusting the polling interval according to the traffic loads can effectively achieve power saving in wireless sensor networks. Thus, there has been a significant research effort in developing polling interval adaptation schemes. Especially, Dynamic Low Power Listening (DLPL) scheme is one of the most widely adopted open-looping polling interval adaptation techniques in wireless sensor networks. In DLPL scheme, if consecutive idle (busy) samplings reach a given fixed threshold, the polling interval is increased (decreased). However, due to the trial-and-error based approach, it may significantly deteriorate the system performance depending on given threshold parameters. In this paper, we propose a novel DLPL scheme, called SDL (Sequential hypothesis testing based Dynamic LPL), which employs sequential hypothesis testing to decide whether to change the polling interval conforming to various traffic conditions. Simulation results show that SDL achieves substantial power saving over state-of-the-art DLPL schemes.