• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2011.05a
• /
• pp.731-734
• /
• 2011

This paper proposed the Low power configuration of Single hop WSN(Wireless Sensor Network) system. When the RF communication is done each tag node during the WSN systems operating, power consumption is greatest. There for, if you configure the Network with the RF communication module turn on/off periodically, power consumption less then operating the module all the time without it toggles. However, some data omissions may occur in which transmission and receipt is done. So this paper proposed the algorithm for low power system without data omissions.

• Proceedings of the KIEE Conference
• /
• 2002.07c
• /
• pp.1649-1651
• /
• 2002

Ultra-wide bandwidth (UWB) detection method has been widely used as a front end detection scheme for the ultra-high frequency (UHF) partial discharge (PD) monitoring systems. A broad-band video detector module was developed and characterized for the UHF UWB PD detection systems. The useable bandwidth of the module is more than 2 GHz and it is optimized for 50-ohm systems. The detection sensitivity and dynamic range of the module were characterized by using a known ns-width RF pulses of GHz range. The dynamic range is more than 6-decades and the module can detect pulsed RF signals down to 1 nW. The detector module can eliminate expensive equipment such as high speed oscilloscopes and radio frequency (RF) spectrum analyzers. Therefore, it enables one to use slow speed data acquisition systems for the PD monitoring at the UHF range. The detector module was used to detect real PDs of about <3 pC. The module converts the UWB PD signals into a low-bandwidth video signal with a high signal-to-noise ratio.

• Journal of Semiconductor Engineering
• /
• v.1 no.1
• /
• pp.13-30
• /
• 2020

Radio frequency (RF) energy harvesting technology have become a reliable and promising alternative to extend the lifetime of power-constrained wireless networks by eliminating the need for batteries. This emerging technology enables the low-power wireless devices to be self-sustaining and eco-friendly by scavenging RF energy from ambient environment or dedicated energy sources. These attributes make RF energy harvesting technology feasible and attractive to an extended range of applications. However, despite being the most reliable energy harvesting technology, there are several challenges (especially power conversion efficiency, output DC voltage and sensitivity) poised for the implementation of RF energy harvesting systems. In this article, a detailed literature on RF energy harvesting technology has been surveyed to provide guidance for RF energy harvesters design. Since signal strength of the received RF power is limited and weak, high efficiency state-of-the-art RF energy harvesters are required to design for providing sufficient DC supply voltage to wireless networks. Therefore, various designs and their trade-offs with comprehensive analysis for RF energy harvesters have been discussed. This paper can serve as a good reference for the researchers to catch new research topics in the field of RF energy harvesting.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2011.10a
• /
• pp.402-403
• /
• 2011

This paper has proposed a $0.13-{\mu}m$ CMOS RF Front-end transmitter for LTE-Advanced systems. The proposed RF Front-end supports a band 7 (from 2500 MHz to 2570 MHz) in E-UTRA of 3GPP. It can provide a maximum output power level of +10 dBm but it's a normal output power level is +0 dBm considering a low PAPR. The post-layout simulation results show that the quadrature up-conversion mixer and a driver amplifier consumes 14 mA and 28 mA from a 1.2 V supply voltage respectively, while providing a output power level of 0 dBm at the input power level of -13 dBm.

• Journal of the Korean Ceramic Society
• /
• v.49 no.5
• /
• pp.399-403
• /
• 2012

SnO thin films were fabricated by rf reactive sputtering on borosilicate substrates with an Sn target and Ar/$O_2$ gas mixture. The effect of rf power on the structural, electrical, and optical properties of SnO thin films was investigated with XRD, AFM, SEM, Hall effect measurements, and UV-Vis spectrometer. As a plasma power increased the crystallinity with a preferred orientation of SnO thin films was improved and the grain size slightly increased. However the grains were coalesced and excessively irregular in shape. The electrical conductivity of SnO thin films demonstrated a relatively low p-type conductivity of 0.024 $(Wcm)^{-1}$ at a higher power condition. Lastly, SnO thin films had poor optical transmittance in the visible range as a plasma power increased.

• IEMEK Journal of Embedded Systems and Applications
• /
• v.4 no.1
• /
• pp.29-34
• /
• 2009

In this paper, we design RF transceiver architecture and building blocks for impulse radio UWB system. Impulse radio UWB signal occupies the wide frequency band which is very low transmission power. So, it can minimize the interference effect with the other system. Using UWB technology, we obtain position awareness service. Therefore, we describe the RF transceiver architecture of direct conversion receiver and define the requirement of RF transceiver. Moreover, we implement a prototype RF transceiver based on the presented standard and verify a function and performance through the wireless data communication and ranging test.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.23 no.7
• /
• pp.791-796
• /
• 2012

A RF limiter is a component to protect the receiver front end from undesired signal. A RF limiter is a key component whose output is constant level for all inputs above a critical value. A RF limiter use a diode to pass signals of low power while attenuating those above some threshold. A RF limiter for receiver protection in modern radar systems is playing a vital role in order to meet challenges of new interference threats and complicated electromagnetic environments. This paper proposed a new circuit for high power RF limiter whose structure is the combination of the PIN diode and Limit diode. PIN diode take a use of its isolation characteristics which act as a switch does. A 2 kW RF limiter with 200 us pulse width at S-band was developed. It shows good agreements between estimated value and measured results.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.11 no.4
• /
• pp.599-609
• /
• 2000

In this paper, sub-harmonically pumped single balanced resistive mixers are presented . Frequency bandwidth is selected for a Ku-band, which is 11.75-12.25GHz for RF, 5.375∼5.625 GHz for LO, and 1 GHz for IF signals. A rat-race hybrid is designed for the accomplishment of single balanced type. A low pass filter (LPF) with photonic band gap(PBG) structure is used for good conversion loss and unwanted harmonics suppression. Two types of mixers are suggested, which are one with no gate bias for no DC power consumption and the other with the IF amplifier for conversion gain. When a LO signal with the power of 6 dBm at 5.5 GHz is injected, a conversion loss of 12.17dB and a conversion gain of 7.83 dB are obtained for each mixer. For the both mixers , LO to RF isolation of 20 dB and LO to IF isolation of 60dB are obtained. With the RF power of -30dBm to -3dBm, the mixer shows linear characteristics region of IF. this mixer can be applied for Ku-band and other microwave communication systems.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.65 no.1
• /
• pp.122-127
• /
• 2016

In this paper, new spectrum sensing schemes based on analog/RF front-end processing are introduced for IoT wireless sensor networks. While the conventional approaches for wireless channel cognition have been issued in signal processing area, the RF spectrum cognition concept makes it feasible to achieve cognitive wireless sensor networks (C-WSNs). The spectrum cognition at RF processing is categorized as four kinds of sensing mechanisms. Two recent reseaches are described as promising candidates for the C-WSN. One senses spectrum by the frequency discriminating receiver, the other senses and detects from the frequency selective super-regenerative receiver. The introduced systems with simple and low-power RF architectures play dual roles of channel sensing and demodulation. simultaneously. Therefore, introduced spectrum sensing receivers can be one of the best candidates for IoT wireless sensor devices in C-WSN environments.

• 제어로봇시스템학회:학술대회논문집
• /
• 2001.10a
• /
• pp.114.6-114
• /
• 2001

According to expansion of wireless communication system and mobile device, interest has been growing in personal navigation system integrated with wireless system. In portable consumer electronics, such as cellular phones, GPS and PDA, one of major design factors is the power consumption. Solutions of reducing the power dissipation are low voltage, low system clock power management and so on. This paper develops a GPS receiver based on the advanced power management algorithm that achieves very low average power consumption. Both RF and DSP chips are powered down and reactivated only when the position fixing is required. In order to run, the developed includes the RTC calibration function and the fast reacquisition function using XMC (eXtended Multiple Correlator) ...