• 대한임베디드공학회논문지
• /
• 제10권6호
• /
• pp.391-397
• /
• 2015

Nonvolatile memories in memory hierarchy have been investigated to reduce its energy consumption because nonvolatile memories consume zero leakage power in memory cells. One of the difficulties is, however, that the endurance of most nonvolatile memory technologies is much shorter than the conventional SRAM and DRAM technology. This has limited its usage to only the low levels of a memory hierarchy, e.g., disks, that is far from the CPU. In this paper, we study the use of a new type of nonvolatile memories - the Phase Change Memory (PCM) with a DRAM buffer system as the main memory. Our design reduced the total energy of a DRAM main memory of the same capacity by 80%. These results indicate that it is feasible to use PCM technology in place of DRAM in the main memory for better energy efficiency.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2008년도 제39회 하계학술대회
• /
• pp.488-489
• /
• 2008

Based on the fact that renewable energies such as photovoltaic, wind power, etc. are increasingly used in distribution systems recently which affects overvoltage, this paper implements an unified power flow controller(UPFC) to compensate voltage swell. The implemented scheme employs an ac chopper and a low-pass filter along with a series transformer. The ac chopper converts the amplitude of the voltage down to the nominal value. The low pass filter makes the rough waveform of the output voltage of the ac chopper due to switching smoothly by eliminating harmonics. To verify the effectiveness of the implemented UPFC, the results by Electro-Magnetic Transients Program(EMTP) are presented for various overvoltage cases.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2014년도 제46회 동계 정기학술대회 초록집
• /
• pp.456.1-456.1
• /
• 2014

Transmutation characteristics of transuranics (TRU) in a transmutation reactor based on LAR (Low Aspect Ratio) tokamak as a neutron source are investigated. Optimum radial build of a transmutation reactor is found by coupled analysis of the tokamak systems and the neutron transport. The dependence of the transmutation characteristics on an aspect ratio, A in the range of 1.5 to 2.5, and on a fusion power in the range of 150 MW to 500 MW are investigated. Equilibrium fuel cycle is developed for effective transmutation and it is shown that with one unit of the transmutation reactor based on the LAR tokamak producing fusion power in the range of a few hundred MW, up to 3 PWRs (1.0 GWe capacity) can be supported with the burn-up fraction bigger than 50%.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1988년도 전기.전자공학 학술대회 논문집
• /
• pp.870-873
• /
• 1988

AESOPS computer program is designed to find those eigenvalues of a linear dynamic system model which most strongly characterize oscillations between generator rotors. The low frequency oscillation actually occurred in October, 1986 in Korean Electric Power Corporation (KEPCO) System. 28 oscillation modes are identified through computer runs and two of them are calculated unstable in the case of the start of a pumped-storage unit. This program is considered to complement the conventional PSS/E stability program for the stability study of KEPCO system.

• 한국세라믹학회지
• /
• 제54권2호
• /
• pp.75-85
• /
• 2017

Thermoelectric is a key technology for energy harvesting and solid-state cooling by direct thermal-to-electric energy conversion (or vice versa); however, the relatively low efficiency has limited thermoelectric systems to niche applications such as space power generation and small-scale or high-density cooling. To expand into larger scale power generation and cooling applications such as ATEG (automotive thermoelectric generators) and HVAC (heating, ventilation, and air conditioning), high-performance bulk thermoelectric materials and their low-cost processing are essential prerequisites. Recently, the performance of commercial thermoelectric materials including $Bi_2Te_3$-, PbTe-, skutterudite-, and half-Heusler-based compounds has been significantly improved through non-equilibrium processing technologies for defect engineering. This review summarizes material design approaches for the formation of multi-dimensional and multi-scale defect structures that can be used to manipulate both the electronic and thermal transport properties, and our recent progress in the synthesis of conventional thermoelectric materials with defect structures is described.

• Journal of Power Electronics
• /
• 제16권3호
• /
• pp.994-1003
• /
• 2016

Two major obstacles in the utilization of electrical vehicles are their price and range. The collaboration of direct torque control (DTC) with induction motor (IM) is preferred for its low cost, easy implementation, and parameter independency. However, in terms of edges, the method has drawbacks, such as variable switching frequency and undesired current harmonic distortion. These drawbacks result in acoustic noise, reduced efficiency, and electromagnetic interference. A feed-forward approach for stator-flux-oriented DTC with space vector pulse-width modulation is presented in in this paper. The outcome of the proposed method is low current harmonic distortion with fixed switching frequency while preserving the torque performance and simple application feature of basic DTC. The method is applicable to existing and forthcoming IM drive systems via software adaptation. The validity of the proposed method is confirmed by simulation and experimental results.

• Journal of Power Electronics
• /
• 제4권4호
• /
• pp.228-236
• /
• 2004

This paper describes the optimal current-control of a permanent magnet synchronous motor by the use of robust and simple current controllers, based upon the analytical procedure known as the inverse LQ (ILQ) design method. The ILQ design method is a strategy for finding the optimal gains based on pole assignment without solving the Riccati equation. It is very important to keep the motor in robust servo-lock. By experiments and simulations, we will show that the ILQ optimal servo-system with servo-lock is more insensitive at low speeds to variations in armature inductance than the standard PI servo-system. Variations in armature inductance have the greatest influence on the responses of a servo-system.

• KIEE International Transaction on Electrical Machinery and Energy Conversion Systems
• /
• 제2B권4호
• /
• pp.214-218
• /
• 2002

In this paper, the effectiveness of three different control algorithms are thoroughly investigated via simulation and a proposed efficiency evaluation method of experimentation. Both the steady state and transient characteristics of each control algorithm along with its measured efficiency are analyzed. Finally, a novel two-mode maximum power point tracking (MPPT) control algorithm combining the constant voltage control and the incremental conduction (IncCond) methods is proposed to improve the efficiency of the 3KW PV power generation system at different insolation conditions. Experimental results show that the proposed two-mode MPPT control provides excellent performance at less than 30% insolation intensity, covering the whole insolation area without additional hardware circuitry.

• KSII Transactions on Internet and Information Systems (TIIS)
• /
• 제13권3호
• /
• pp.1599-1610
• /
• 2019

Intelligent services have expanded as Internet of Things (IoT) technology has evolved and new requirements emerge to accommodate various services. One new requirement is transmitting data over long distances with low-power. Researchers have developed low power wide area (LPWA) network technology to satisfy the requirement; this can improve IoT network infrastructure and increase the range of services. However, network coverage expansion causes several problems. The traffic load is concentrated at a specific gateway, which causes network congestion and leads to decreased transmission efficiency. Therefore, the approach proposed in this paper attempts to recognize and then avoid congestion through gateway channel hopping. The LPWA network employs multiple channels, so wireless channel hopping is available in a gateway. Devices that are not delay sensitive wait for the gateway to reappear on their wireless channel; delay sensitive devices change the wireless channel along the hopping gateway. Thus, the traffic load and congestion in each wireless channel can be reduced improving transmission efficiency. The proposed approach's performance is evaluated by computer simulation and verified in terms of transmission efficiency.

• 대한임베디드공학회논문지
• /
• 제18권4호
• /
• pp.151-157
• /
• 2023

RPL (IPv6 Routing Protocol for Low-power Lossy Network) is a standardized routing protocol for LLNs (Low power and Lossy Networks) by the IETF (Internet Engineering Task Force). RPL creates routes and builds a DODAG (Destination Oriented Directed Acyclic Graph) through OF (Objective Function) defining routing metrics and optimization objectives. RPL supports a leaf mode which does not allow any child nodes. In this paper, we propose INFRA-RPL which provides a dynamic leaf mode functionality to a leaf node with the mobility. The proposed protocol is implemented in the open-source IoT operating system, Contiki-NG and Cooja simulator, and its performance is evaluated. The evaluation results show that INFRA-RPL outperforms the existing protocols in the terms of PDR, latency, and control message overhead.