Fine-size exposed aggregate portland cement concrete pavements (FEACP) have surface texture of exposed aggregate by removing upper 2$\sim$3mm mortar of surface of which curing is delayed by using delay-setting agent. FEACPs have advantages of maintaining low-noise and adequate skid-resistance level during the performance period than general portland cement concrete pavements. It is necessary to ensure the durability environmental loading to prevent unexpected distress during the service life of FEACP. In the process of curing, volume change accompanied change in by moisture and temperature could be an important cause of crack in concrete to construct for successful FEACP, The use of chloride containing deicer may accelerate defects of concrete pavement, such as crack and scaling. This study aim to evaluate environmental loading resistance of FEACP, based on the estimation of shrinkage-crack-control-capability by moisture evaporation and scaling by deicer in freeze-thaw reaction.
Journal of the Institute of Electronics Engineers of Korea SC
/
v.43
no.5
s.311
/
pp.36-43
/
2006
In this paper we present a new high-speed parallel multiplier for Performing the bit-parallel multiplication of two polynomials in the finite fields $GF(2^m)$. Prior to construct the multiplier circuits, we consist of the MOD operation part to generate the result of bit-parallel multiplication with one coefficient of a multiplicative polynomial after performing the parallel multiplication of a multiplicand polynomial with a irreducible polynomial. The basic cells of MOD operation part have two AND gates and two XOR gates. Using these MOD operation parts, we can obtain the multiplication results performing the bit-parallel multiplication of two polynomials. Extending this process, we show the design of the generalized circuits for degree m and a simple example of constructing the multiplier circuit over finite fields $GF(2^4)$. Also, the presented multiplier is simulated by PSpice. The multiplier presented in this paper use the MOD operation parts with the basic cells repeatedly, and is easy to extend the multiplication of two polynomials in the finite fields with very large degree m, and is suitable to VLSI. Also, since this circuit has a low propagation delay time generated by the gates during operating process because of not use the memory elements in the inside of multiplier circuit, this multiplier circuit realizes a high-speed operation.
The purpose of this study is to estimate the behavior and the mechanism of debris flow at the end of mountain side when a berm was set on the inclined plane. The numerical model was performed by using the Finite Difference Method(FDM) based on the equation for the mass conservation and momentum conservation. In order to measure the behavior of the debris flow, the debris flow of a straight channel slope and the debris flow of channel slope with 3 types of berms were compared. First, the flow discharge and the sediment volume concentration at the downstream of the channel slope, depending on the various berm width and the different inflow discharges at the upstream of the channel were analyzed. The longer the berm width, the flow discharge at the downstream of the channel was decreased and the high flow fluctuation was reduced by a berm. And it means that a berm can effect for the delay of the debris flow. Through Root Mean Square ratio(RMS) comparison, the flow discharge of the channel slope with a berm was lower than that of a straight channel slope. The longer the berm width, for the sediment volume concentration, an inflection point did not show but mild curve. Because the low sediment concentration with water mixture by a berm continuously flow at the downstream end, it will be effect for reducing the disaster caused by debris flow. The results of this study will provide useful information in predicting and preventing disaster caused by the debris flow.
Kim, Yong-Bok;Oh, Si-Hwan;Lee, Seon-Ho;Yong, Ki-Lyok;Rhee, Seung-Wu
Aerospace Engineering and Technology
/
v.6
no.1
/
pp.74-82
/
2007
The M-Method that measures the speed of actuator with counting the number of Reaction wheel Tacho Pulse has the many advantages such that a realization is simple and measuring time is uniform, but it also has the disadvantage that measuring speed becomes worse as the wheel speed goes lower. On the contrary, the T-Method that measures the time duration between the pulses is more accurate at lower-speed and its time delay is smaller than M-Method, but its realization is more difficult than M-Method because measuring time is varying with wheel speed variation. Thought M/T Method mixing M-Method with T-Method is widely used in order to measure the speed in the motor industrial area, one of two methods has been used in the spacecraft design area. Therefore, we try to apply both methods together to measuring the speed of Reaction Wheel, the core actuator for low earth orbit satellite. This paper provides the Reaction Wheel simulation board located in the Spacecraft Dynamic Simulator, ground support test set.
Shin, Hyeon Ju;Kim, Young Nam;Kim, Ju Hee;Son, In Sook;Bang, Kyung-Sook
Child Health Nursing Research
/
v.20
no.3
/
pp.215-224
/
2014
Purpose: This study was conducted to identify risk factors in hospitalized children, and to develop and validate a fall-risk assessment tool for hospitalized children. Methods: A retrospective chart review was performed at one university children's hospital, and an analysis was done of the characteristics of all patients who fell during a 44-month period (n=48). These patients were compared with another 149 hospitalized children who did not fall. Results: Significant predictors of falls as identified in a multivariate logistic regression analyses were age of less than 3 years old, neurological diagnosis including epilepsy, children's dependency of ADL, physical developmental delay, multiple usage of fall-risk-increasing drugs. The respective odds ratios ranged from 2.4 to 7.1 with 95% confidence interval (p<0.05). Accordingly, defining patients with either 5 risk factors as fall-prone hospitalized children provided a sensitivity of 93.6% and specificity of 16.2%. Conclusion: The results show that this tool has an acceptable level of sensitivity to assess the risk factors of fall in hospitalized children even though the specificity was low, suggesting that this tool may enable nurses to predict the risk level of childhood falls, and develop preventive strategies against pediatric falls in children's units.
In organic fanning systems, integration of cover crops into cropping system are recommended to improve the soil quality, to prevent soil erosion, and to provide biological control of weeds. The aim of the present study was to evaluate the optimal seeding dates of major cover crops. To know optimal seeding dates, crimson clover, alfalfa, rye and hairy vetch were sown on 20. Sep., 27. Sep., 4. Oct., 11. Oct., 18. Oct., 25. Oct. Rye could germinate and grow well in all the tested sowing dates. Hence, it was concluded that the sowing of rye could be conducted later in fall or more earlier in spring than any other cover crops tested in this study. Growth and ground covering capacity were significantly decreased by late sowing in alfalfa and crimson clover. For safe overwintering, alfalfa and crimson clover should be sown before late September. Similarly, field emergence of hairy vetch was found to be sensitive to soil temperature, however, its growth and ground covering capacity after overwintering was enough to compensate the delay in sowing. Germination tests in laboratory revealed that hairy vetch grew faster at $25^{\circ}C$ compared to $20^{\circ}C$. The result suggested that germination and growth rate of hairy vetch was rapidly decreased at low temperature. Therefore, it is recommended that hairy vetch should be sown as soon as possible in September for improving stand establishment after overwintering.
Ha Kyoo-Chul;Ko Kyung-Seok;Koh Dong-Chan;Yum Byoung-Woo;Lee Kang-Kun
Economic and Environmental Geology
/
v.39
no.3
s.178
/
pp.269-284
/
2006
Aquifer responses to the river stage fluctuations were analyzed between the groundwater level and the river stage in an alluvial aquifer. The auto-correlation and cross-correlation as a time series analysis were applied. Study site is a floodplain in the Mangyeong river. Groundwater levels in each depth representing the silt and sand(SS), gravel and sand(GS), and weathered zone(WZ) layer were monitored. The groundwater levels were more sensitive to the river stage fluctuations than rainfall. Since the river stages are influenced by the gate operations downstream and tide, show periodic patterns, and the correlation coefficients with rainfall is low. Cross-correlation function between groundwater level in each depth do not show any delay time, then response time is very short to each depth. Cross-correlation analysis were performed to estimate the response time of groundwater levels to river stage fluctuations. Groundwater levels respond to the river stage within 30 minutes to 1 hour in wells near the stream. Short time lag between groundwater level and river stage indicates the quick response. A different response time imply the hydraulic inhomogeneity of the site, and a probable high permeability zone between river and aquifer can be inferred. Mangyeong-river in study site is a gaining stream normally, and river stage rising by gate operation or floods makes river water flow into groundwater. The auto-correlation and cross-correlation functions as a time series analysis can be a good tool to interpret the aquifer responses to stream stage fluctuation
This paper experimentally investigates the effects of oxygen-enriched air (OEA) on the running behaviors of an LPG SI engine during both start/warm-up (SW) and hot idling (HI) stages. The experiments were performed on an air-cooled, single-cylinder, 4-stroke, LPG SI engine with an electronic fuel injection system and an electrically-heated oxygen sensor. OEA containing 23% and 25% oxygen (by volume) was supplied for the experiments. The throttle position was fixed at that of idle condition. A fueling strategy was used as following: the fuel injection pulse width (FIPW) in the first cycle of injection was set 5.05 ms, and 2.6 ms in the subsequent cycles till the achieving of closed-loop control. In closed-loop mode, the FIPW was adjusted by the ECU in terms of the oxygen sensor feedback. Instantaneous engine speed, cylinder pressure, engine-out time-resolved HC, CO and NOx emissions and excess air coefficient (EAC) were measured and compared to the intake air baseline (ambient air, 21% oxygen). The results show that during SW stage, with the increase in the oxygen concentration in the intake air, the EAC of the mixture is much closer to the stoichiometric one and more oxygen is made available for oxidation, which results in evidently-improved combustion. The ignition in the first firing cycle starts earlier and peak pressure and maximum heat release rate both notably increase. The maximum engine speed is elevated and HC and CO emissions are reduced considerably. The percent reductions in HC emissions are about 48% and 68% in CO emissions about 52% and 78%; with 23% and 25% OEA, respectively, compared to ambient air. During HI stage, with OEA, the fuel amount per cycle increases due to closed-loop control, the engine speed rises, and speed stability is improved. The HC emissions notably decrease: about 60% and 80% with 23% and 25% OEA, respectively, compared to ambient air. The CO emissions remain at the same low level as with ambient air. During both SW and HI stages, intake air oxygen enrichment causes the delay of spark timing and the increased NOx emissions.
The salted small shrimps(Acetes japonicus) were fermented for 3 months at room temperature. During the period of fermentation, the changes of shrimp protein properties were determined. The extractability of soluble protein was slightly decreased in 1 month fermentation, but thereafter increased. The contents of 10% TCA soluble fraction were gradually increased during 3 month fermentation, and the rate of 10% TCA soluble fraction/total soluble protein was also greatly increased during the period of fermentation. Sephadex G-100 gel filtration pattern was changed after 1 month fermentation, showing the disappearance of low molecular weight protein peaks, the decomposition and the delay of elution time of main shrimp protein peaks. Polyacrylamide gel disc electrophoresis patterns showed the degradation of main protein bands into lots of smaller bands after 1 month fermentation. The contents of total free amino acids were slightly decreased in 1 month fermentation and then gradually increased during the Period of fermentation. The rate of free amino acids/soluble protein was steadily increased during the period of fermentation, but the rate of free amino acids/10% TCA soluble fraction was decreased continually during the period of fermentation. The contents of most free amino acids were increased during the period of fermentation, but those of histidine and arginine were greatly decreased in 1 month fermentation. Ammonia was increased after 1 month fermentation. The pH value of salted shrimp was slowly changed during 3 months of fermentation, showing increase from 7.8 to 8.2.
Objectives: The pandemic of novel influenza A (H1N1) virus has required decision-makers to act in the face of the substantial uncertainties. In this study, we evaluated the potential impact of the pandemic response strategies in the Republic of Korea using a mathematical model. Methods: We developed a deterministic model of a pandemic (H1N1) 2009 in a structured population using the demographic data from the Korean population and the epidemiological feature of the pandemic (H1N1) 2009. To estimate the parameter values for the deterministic model, we used the available data from the previous studies on pandemic influenza. The pandemic response strategies of the Republic of Korea for novel influenza A (H1N1) virus such as school closure, mass vaccination (70% of population in 30 days), and a policy for anti-viral drug (treatment or prophylaxis) were applied to the deterministic model. Results: The effect of two-week school closure on the attack rate was low regardless of the timing of the intervention. The earlier vaccination showed the effect of greater delays in reaching the peak of outbreaks. When it was no vaccination, vaccination at initiation of outbreak, vaccination 90 days after the initiation of outbreak and vaccination at the epidemic peak point, the total number of clinical cases for 400 days were 20.8 million, 4.4 million, 4.7 million and 12.6 million, respectively. The pandemic response strategies of the Republic of Korea delayed the peak of outbreaks (about 40 days) and decreased the number of cumulative clinical cases (8 million). Conclusions: Rapid vaccination was the most important factor to control the spread of pandemic influenza, and the response strategies of the Republic of Korea were shown to delay the spread of pandemic influenza in this deterministic model.
본 웹사이트에 게시된 이메일 주소가 전자우편 수집 프로그램이나
그 밖의 기술적 장치를 이용하여 무단으로 수집되는 것을 거부하며,
이를 위반시 정보통신망법에 의해 형사 처벌됨을 유념하시기 바랍니다.
[게시일 2004년 10월 1일]
이용약관
제 1 장 총칙
제 1 조 (목적)
이 이용약관은 KoreaScience 홈페이지(이하 “당 사이트”)에서 제공하는 인터넷 서비스(이하 '서비스')의 가입조건 및 이용에 관한 제반 사항과 기타 필요한 사항을 구체적으로 규정함을 목적으로 합니다.
제 2 조 (용어의 정의)
① "이용자"라 함은 당 사이트에 접속하여 이 약관에 따라 당 사이트가 제공하는 서비스를 받는 회원 및 비회원을
말합니다.
② "회원"이라 함은 서비스를 이용하기 위하여 당 사이트에 개인정보를 제공하여 아이디(ID)와 비밀번호를 부여
받은 자를 말합니다.
③ "회원 아이디(ID)"라 함은 회원의 식별 및 서비스 이용을 위하여 자신이 선정한 문자 및 숫자의 조합을
말합니다.
④ "비밀번호(패스워드)"라 함은 회원이 자신의 비밀보호를 위하여 선정한 문자 및 숫자의 조합을 말합니다.
제 3 조 (이용약관의 효력 및 변경)
① 이 약관은 당 사이트에 게시하거나 기타의 방법으로 회원에게 공지함으로써 효력이 발생합니다.
② 당 사이트는 이 약관을 개정할 경우에 적용일자 및 개정사유를 명시하여 현행 약관과 함께 당 사이트의
초기화면에 그 적용일자 7일 이전부터 적용일자 전일까지 공지합니다. 다만, 회원에게 불리하게 약관내용을
변경하는 경우에는 최소한 30일 이상의 사전 유예기간을 두고 공지합니다. 이 경우 당 사이트는 개정 전
내용과 개정 후 내용을 명확하게 비교하여 이용자가 알기 쉽도록 표시합니다.
제 4 조(약관 외 준칙)
① 이 약관은 당 사이트가 제공하는 서비스에 관한 이용안내와 함께 적용됩니다.
② 이 약관에 명시되지 아니한 사항은 관계법령의 규정이 적용됩니다.
제 2 장 이용계약의 체결
제 5 조 (이용계약의 성립 등)
① 이용계약은 이용고객이 당 사이트가 정한 약관에 「동의합니다」를 선택하고, 당 사이트가 정한
온라인신청양식을 작성하여 서비스 이용을 신청한 후, 당 사이트가 이를 승낙함으로써 성립합니다.
② 제1항의 승낙은 당 사이트가 제공하는 과학기술정보검색, 맞춤정보, 서지정보 등 다른 서비스의 이용승낙을
포함합니다.
제 6 조 (회원가입)
서비스를 이용하고자 하는 고객은 당 사이트에서 정한 회원가입양식에 개인정보를 기재하여 가입을 하여야 합니다.
제 7 조 (개인정보의 보호 및 사용)
당 사이트는 관계법령이 정하는 바에 따라 회원 등록정보를 포함한 회원의 개인정보를 보호하기 위해 노력합니다. 회원 개인정보의 보호 및 사용에 대해서는 관련법령 및 당 사이트의 개인정보 보호정책이 적용됩니다.
제 8 조 (이용 신청의 승낙과 제한)
① 당 사이트는 제6조의 규정에 의한 이용신청고객에 대하여 서비스 이용을 승낙합니다.
② 당 사이트는 아래사항에 해당하는 경우에 대해서 승낙하지 아니 합니다.
- 이용계약 신청서의 내용을 허위로 기재한 경우
- 기타 규정한 제반사항을 위반하며 신청하는 경우
제 9 조 (회원 ID 부여 및 변경 등)
① 당 사이트는 이용고객에 대하여 약관에 정하는 바에 따라 자신이 선정한 회원 ID를 부여합니다.
② 회원 ID는 원칙적으로 변경이 불가하며 부득이한 사유로 인하여 변경 하고자 하는 경우에는 해당 ID를
해지하고 재가입해야 합니다.
③ 기타 회원 개인정보 관리 및 변경 등에 관한 사항은 서비스별 안내에 정하는 바에 의합니다.
제 3 장 계약 당사자의 의무
제 10 조 (KISTI의 의무)
① 당 사이트는 이용고객이 희망한 서비스 제공 개시일에 특별한 사정이 없는 한 서비스를 이용할 수 있도록
하여야 합니다.
② 당 사이트는 개인정보 보호를 위해 보안시스템을 구축하며 개인정보 보호정책을 공시하고 준수합니다.
③ 당 사이트는 회원으로부터 제기되는 의견이나 불만이 정당하다고 객관적으로 인정될 경우에는 적절한 절차를
거쳐 즉시 처리하여야 합니다. 다만, 즉시 처리가 곤란한 경우는 회원에게 그 사유와 처리일정을 통보하여야
합니다.
제 11 조 (회원의 의무)
① 이용자는 회원가입 신청 또는 회원정보 변경 시 실명으로 모든 사항을 사실에 근거하여 작성하여야 하며,
허위 또는 타인의 정보를 등록할 경우 일체의 권리를 주장할 수 없습니다.
② 당 사이트가 관계법령 및 개인정보 보호정책에 의거하여 그 책임을 지는 경우를 제외하고 회원에게 부여된
ID의 비밀번호 관리소홀, 부정사용에 의하여 발생하는 모든 결과에 대한 책임은 회원에게 있습니다.
③ 회원은 당 사이트 및 제 3자의 지적 재산권을 침해해서는 안 됩니다.
제 4 장 서비스의 이용
제 12 조 (서비스 이용 시간)
① 서비스 이용은 당 사이트의 업무상 또는 기술상 특별한 지장이 없는 한 연중무휴, 1일 24시간 운영을
원칙으로 합니다. 단, 당 사이트는 시스템 정기점검, 증설 및 교체를 위해 당 사이트가 정한 날이나 시간에
서비스를 일시 중단할 수 있으며, 예정되어 있는 작업으로 인한 서비스 일시중단은 당 사이트 홈페이지를
통해 사전에 공지합니다.
② 당 사이트는 서비스를 특정범위로 분할하여 각 범위별로 이용가능시간을 별도로 지정할 수 있습니다. 다만
이 경우 그 내용을 공지합니다.
제 13 조 (홈페이지 저작권)
① NDSL에서 제공하는 모든 저작물의 저작권은 원저작자에게 있으며, KISTI는 복제/배포/전송권을 확보하고
있습니다.
② NDSL에서 제공하는 콘텐츠를 상업적 및 기타 영리목적으로 복제/배포/전송할 경우 사전에 KISTI의 허락을
받아야 합니다.
③ NDSL에서 제공하는 콘텐츠를 보도, 비평, 교육, 연구 등을 위하여 정당한 범위 안에서 공정한 관행에
합치되게 인용할 수 있습니다.
④ NDSL에서 제공하는 콘텐츠를 무단 복제, 전송, 배포 기타 저작권법에 위반되는 방법으로 이용할 경우
저작권법 제136조에 따라 5년 이하의 징역 또는 5천만 원 이하의 벌금에 처해질 수 있습니다.
제 14 조 (유료서비스)
① 당 사이트 및 협력기관이 정한 유료서비스(원문복사 등)는 별도로 정해진 바에 따르며, 변경사항은 시행 전에
당 사이트 홈페이지를 통하여 회원에게 공지합니다.
② 유료서비스를 이용하려는 회원은 정해진 요금체계에 따라 요금을 납부해야 합니다.
제 5 장 계약 해지 및 이용 제한
제 15 조 (계약 해지)
회원이 이용계약을 해지하고자 하는 때에는 [가입해지] 메뉴를 이용해 직접 해지해야 합니다.
제 16 조 (서비스 이용제한)
① 당 사이트는 회원이 서비스 이용내용에 있어서 본 약관 제 11조 내용을 위반하거나, 다음 각 호에 해당하는
경우 서비스 이용을 제한할 수 있습니다.
- 2년 이상 서비스를 이용한 적이 없는 경우
- 기타 정상적인 서비스 운영에 방해가 될 경우
② 상기 이용제한 규정에 따라 서비스를 이용하는 회원에게 서비스 이용에 대하여 별도 공지 없이 서비스 이용의
일시정지, 이용계약 해지 할 수 있습니다.
제 17 조 (전자우편주소 수집 금지)
회원은 전자우편주소 추출기 등을 이용하여 전자우편주소를 수집 또는 제3자에게 제공할 수 없습니다.
제 6 장 손해배상 및 기타사항
제 18 조 (손해배상)
당 사이트는 무료로 제공되는 서비스와 관련하여 회원에게 어떠한 손해가 발생하더라도 당 사이트가 고의 또는 과실로 인한 손해발생을 제외하고는 이에 대하여 책임을 부담하지 아니합니다.
제 19 조 (관할 법원)
서비스 이용으로 발생한 분쟁에 대해 소송이 제기되는 경우 민사 소송법상의 관할 법원에 제기합니다.
[부 칙]
1. (시행일) 이 약관은 2016년 9월 5일부터 적용되며, 종전 약관은 본 약관으로 대체되며, 개정된 약관의 적용일 이전 가입자도 개정된 약관의 적용을 받습니다.