• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2020년도 가을 학술논문 발표대회
• /
• pp.10-11
• /
• 2020

This research is part of the research for unifying the mass concrete and utilizing the rate of super retarding agent. We analyzed the performance of super retarding agent under low temperature conditions. It was found that there was no deterioration in fluidity and air quality due to the change in the super retarding agent mixing rate. It was found that when super retarding agent was mixed up to 0.5 %, it was delayed for 22.3 hours at 20℃, 48.2 hours at 10℃, and 48.5 hours at 5℃. Therefore in order to ensure the performance required at the site, the super retarding agent mixing rate must be determined by fully considering the situation at the site. In addition it will be analyzed that super retarding agent performance analysis at high temperature will be required in subsequent studies.

• 한국윤활학회:학술대회논문집
• /
• 한국윤활학회 2002년도 제35회 춘계학술대회
• /
• pp.215-225
• /
• 2002

In order to enhance the thermal stability of binder materials of bonded type solid lubricants, several combinations of metal-alkoxide based sol-gel materials such as methyltrimethoxysilane(MTMOS), $titaniumisopropoxide(Ti(Opr^{j})_{4})$, $zirconiumisopropoxide(Zr(Opr^{j})_{4})$ and $aluminumbutoxide(Al(Obu^{t})_{4})$ were chemically modified by epoxy-, acrylic- and fluoro-silane compounds, respectively, in this work. Friction and wear characteristics of these hybrid ceramic materials were tested with a micro tribe-tester where a reciprocating steel ball slid on a test material, and the tribological property was also evaluated with respect to both heat-curing temperature and tile time. Test results generally showed that hybrid ceramic materials modified by epoxy-silane compounds had a low friction compared to others. And the higher heat-curing temperature and the longer heat treatment time resulted in the higher friction and the lower wear. IR spectroscopic analyses revealed that it was caused mainly by the increased metal oxide content in hybrid ceramics when the heat-curing temperature was over $320^{\circ}C$.

• Tribology and Lubricants
• /
• 제18권5호
• /
• pp.324-332
• /
• 2002

In order to enhance the thermal stability of binder materials of bonded type solid lubricants, several metal-alkoxide based sol-gel materials such as methyltrimethoxysilane(MTMOS), titaniumisopropoxide$(Ti(Opr^i)_4),$ zirconiumisopropoxide $(Zr(Opr^i)_4)$ and aluminumbutoxide$(Al(Obu^t)_4)$ were chemically modified by epoxy-, acrylic- and fluoro-silane compounds, respectively. Friction and wear characteristics of these hybrid ceramic materials were tested with a micro tribo-tester, and evaluated with respect to both heat-curing temperature and the time. Test results generally showed that hybrid ceramic materials modified by epoxy-silane compounds had a low friction compared to others. And the higher het-curing temperature and the longer heat treatment time resulted in the higher friction and the lower wear. IR spectroscopic analyses revealed that these results were caused mainly by the increased metal oxide content in hybrid ceramics when the heat-curing temperature was over $320^{\circ}C.$

• 한국세라믹학회지
• /
• 제18권3호
• /
• pp.192-200
• /
• 1981

This study deals with the low temperature ($25^{\circ}C$-$600^{\circ}C$) properties of Kaolin-Phosphate-water systems. Phosphoric acid, mono aluminum phosphate, mono ammonium phosphate, the mixture of phosphoric acid and mono aluminum phosphate, and the mixture of phosphoric acid and mono ammonium phosphate were used to characterize the M.O.R. of the systems with to quantity of phosphates, curing time, and firing temperature. Firing shrinkage, viscosity, surface tension, DTA, TGA, and X-ray diffraction patterns were also measured in order to investigated the factors of strengthening. The results of this study were summarized as follows: 1. The M.O.R. of kaolin-phosphate systems were stronger than that of Kaolin-water system at room temperature or low temperature($25^{\circ}C$-$600^{\circ}C$). Though it was increased according to the longer curing time, the higher temperature, and the more addition of phosphate, the M.O.R. were decreased in the case of 10 wt% phosphate addition in the system of phosphoric acid, mono aluminum phosphate and phosphoric acid-mono aluminum phosphate. 2. When the concentration of Phosphate was at 4 wt%, the M.O.R. of specimen cured at $25^{\circ}C$ and added to the phosphoric acid was strongest among the specimens in added to the others phosphates. Whereas, when the concentration of phosphate was above 6wt%, the M.O.R. of specimen cured at $25^{\circ}C$ and added to the phosphoric acid mono ammonium phosphate system cured at $25^{\circ}C$ was the strongest. 3. The M.O.R. of the specimen heated, in the temperature range of 15$0^{\circ}C$-1$600^{\circ}C$, and added to the mixture of phosphoric acid-mono aluminum phosphate system or phosphoric acid-mono ammonium phosphate system was stronger than that of specimen added to Phosphoric acid, mono-aluminum Phosphate or mono-ammonium phosphate alone. 4. The bonding force of phosphate binders was more closely related to surface tension than viscosity and it tended to be inversely proportional to surface tension. The bonding force after heating treatment seemed to be caused by the change of structure of phosphate according to heating.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2004년도 춘계 학술발표회 제16권1호
• /
• pp.228-231
• /
• 2004

The purpose of this study evaluates possibilities of waste phosphogypsum into concrete by steam curing admixture. The waste phosphogypsums were classified into 4 forms(Dihydrate, $\beta-Hemihydrate$, III-Anhydrite and II-Anhydrite) which were changed to in low temperature of calcination. Also, various admixtures were made of waste phosphogypsum(PG) and pozollanic fine powderers (Fly-ash, Blast Furnace Slag), and the basic properties of the cement mortars incorporating with these admixtures were examined and analyzed under a verity of experimental conditions. As a result, III-Anhydrite, these is similar to II-Anhydrite from compressive strength and are great in the effect of strength improvement. also, it was proved that specimens made on type III-Anhydrite of waste phosphogypsum and blast furnace slag increased on the compressive strength of cement mortar. Therefore, III-Anhydrite phosphogypsum calcined at lower temperature could be used as steam curing admixture for concrete 2th production.

• Restorative Dentistry and Endodontics
• /
• 제29권1호
• /
• pp.58-67
• /
• 2004

The objectives of this study was to evaluate current visible light curing units regarding microhardness and microleakage. Fourty samples of composite resin(Z-250, 3M) were cured by different light curing units (Flipo, LOKKI; Credi II, 3M; XL 3000, 3M: Optilux 500, Demetron) in acrylic blocks. Microhardness was measured using a calibrated Vickers indenter on both top and bottom surfaces after 24 hours of storage in air at room temperature. Class V cavities were prepared on buccal and lingual surfaces of fourty extracted human molars. Each margin was on enamel and dentin/cementum. Composite resin(Z-250, 3M) was filled in cavities and cured by four different light curing units (Flipo, LOKKl; Credi II, 3M; XL 3000, 3M: Optilux 500, Demetron). The results of this syudy were as follows: Microhardness 1. Flipo showed low microhardness compared to Optilux 500, Credi II significantly in upper surface. Flipo didn't show a significant difference compared to XL 3000. 2. The microhardness resulting from curing with Flipo was lower than that of others on lower surfaces. Microleakage 1. Dentin margin showed significantly high dye penetration rate than enamel margin in all groups(p<0.05). 2. No significant differences were found on both enamel and dentin margin regarding curing units.

• 콘크리트학회논문집
• /
• 제15권4호
• /
• pp.541-548
• /
• 2003

본 연구는 내한촉진제를 사용한 콘크리트의 현장 적용성을 알아보기 위한 기초적인 실험으로서, 실물부재시험을 통해 각종 양생방법에 따른 온도이력 및 강도특성을 검토하고 한중콘크리트에서 실구조물과 동일한 강도이력을 가질 수 있도록 강도관리용 공시체의 적정 양생방법을 평가하기 위한 것이다. 실물부재시험에서 양생방법에 따른 온도이력은 일반콘크리트(단열양생), 일반콘크리트(급열양생), 내한촉진제 콘크리트 및 일반콘크리트(양생막 양생) 순으로 크게 저하하는 경향을 보이고 있었다. 강도특성은 양생조건이 열악한 양생막 내 외부에서의 일반콘크리트 공시체의 경우에는 초기동해에 따른 강도발현 저하를 보인 반면에 내한촉진제 콘크리트의 경우에는 재령이 경과할수록 계속적인 강도발현을 보이고 있어 내한촉진제의 사용에 따른 동결온도 저하효과 및 저온환경하에서의 경화촉진효과를 나타내고 있었다. 한중콘크리트의 강도관리용 공시체의 적정 양생방법을 검토한 결과, 부재 내부에 매립하여 양생한 경우 및 간이단열양생을 실시한 경우에 있어서의 구조체 콘크리트와의 온도이력은 다소 차이를 나타내고 있지만, 코어강도와는 비교적 근사하게 나타나고 있어 구조체 강도평가를 위한 이들 양생방법의 유효성을 확인할 수 있었다.

• ETRI Journal
• /
• 제38권6호
• /
• pp.1163-1171
• /
• 2016

Integration technologies involving flexible substrates are receiving significant attention owing the appearance of new products regarding wearable and Internet of Things technologies. There has been a continuous demand from the industry for a reliable bonding method applicable to a low-temperature process and flexible substrates. Up to now, however, an anisotropic conductive film (ACF) has been predominantly used in applications involving flexible substrates; we therefore suggest low-temperature lead-free soldering and bonding processes as a possible alternative for flex-on-flex applications. Test vehicles were designed on polyimide flexible substrates (FPCBs) to measure the contact resistances. Solder bumping was carried out using a solder-on-pad process with Solder Bump Maker based on Sn58Bi for low-temperature applications. In addition, thermocompression bonding of FPCBs was successfully demonstrated within the temperature of $150^{\circ}C$ using a newly developed fluxing underfill material with fluxing and curing capabilities at low temperature. The same FPCBs were bonded using commercially available ACFs in order to compare the joint properties with those of a joint formed using solder and an underfill. Both of the interconnections formed with Sn58Bi and ACF were examined through a contact resistance measurement, an $85^{\circ}C$ and 85% reliability test, and an SEM cross-sectional analysis.

• 패션비즈니스
• /
• 제16권1호
• /
• pp.41-51
• /
• 2012

Polyester is mainly used as a bedding filler material. PLA fiber as an eco-friendly material for substituting polyester has a low melting temperature and therefore a hardening process is impossible. This study is to develop the oil for feather touch that can treat at the melting temperature of PLA. The slippery and soft aminosilicone emulsion, and the bulky epoxysilicone emulsion were used. They had proper viscosity and particle size for flexibility and elasticity. When using methoxy aminosilane [$H_2NSi(OCH_3)_3$] as an aminosilane and [$Zn(OCOCH_3)_2$] as a catalyst, the hardening reaction was fast and effective. Feather touch process were treated by 2 steps. At first step, aminosilicone emulsion, epoxysilicone emulsion and methylaminosilane were mixed and homogenized, and at second step, 5% blened solution of the first step, Zn catalyst 1%, distilled water 94% were treated at PLA fiber. After treatment the static friction coefficient and dynamic friction coefficient were reduced to 23.5-60.8% and 30.0-61.3% respectively, and the laundry and sun light fastnesses have not shown any decrease.

• 한국작물학회지
• /
• 제31권4호
• /
• pp.420-425
• /
• 1986

Br, 21을 공시하여 급건엽이 발생하는 환경조건을 구명하기 위하여 온습도를 시험 I과 II로 구분하여 시험 I은 주간의 온습도를 달리하고 야간은 휴건하였으며, 시험 II는 황변 이후에 주야간 동일한 온습도를 건조상 내에서 각기 달리 조사하여 처리하였던 바 그 결과를 요약하면 다음과 같다. 1. 급건엽발생은 고온 저습에 의해 과도한 탈수로 발생되었다. 2. 야간은 휴건하고 주간은 습도 75~80%일 때35$^{\circ}C$ 이하에서는 급건엽이 거의 기생되지 않았다. 3. 주야간 온습도가 일정할 경우 3$0^{\circ}C$는 75~80%, 35$^{\circ}C$는 80~85%, 4$0^{\circ}C$는 85~90%로 온도가 상승할수록 습도를 더 높여야 급건엽이 발생되지 않았다. 4. 급건엽발생이 많을 수록 물리성이 불량하였고, 내용성분이 충분히 분해되지 않았다.