• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.21 no.12
• /
• pp.3235-3245
• /
• 1996

A DDFS(Direct Digital Frequency Synthesizer) used in spread spectrum communication systems must need fast switching speed, high resolution(the step size of the synthesizer), small size and low power. The chip has been designed with four parallel sine look-up table to achieve four times throughput of a single DDFS. To achieve a high processing speed DDFS chip, a 24-bit pipelined CMOS technique has been applied to the phase accumulator design. To reduce the size of the ROM, each sine ROM of the DDFS is stored 0-.pi./2 sine wave data by taking advantage of the fact that only one quadrant of the sine needs to be stored, since the sine the sine has symmetric property. And the 8 bit of phase accumulator's output are used as ROM addresses, and the 2 MSBs control the quadrants to synthesis the sine wave. To compensate the spectrum purity ty phase truncation, the DDFS use a noise shaper that structure like a phase accumlator. The system input clock is divided clock, 1/2*clock, and 1/4*clock. and the system use a low frequency(1/4*clock) except MUX block, so reduce the power consumption. A 107MHz DDFS(Direct Digital Frequency Synthesizer) implemented using 0.8.mu.m CMOS gate array technologies is presented. The synthesizer covers a bandwidth from DC to 26.5MHz in steps of 1.48Hz with a switching speed of 0.5.mu.s and a turing latency of 55 clock cycles. The DDFS synthesizes 10 bit sine waveforms with a spectral purity of -65dBc. Power consumption is 276.5mW at 40MHz and 5V.

• Korean Journal of Remote Sensing
• /
• v.21 no.4
• /
• pp.287-302
• /
• 2005

Digital Elevation Models (DEMs) were generated by ERS-l/2 and JERS-1 SAR interferometry in Daejon area, Korea. The quality of the DEM's was evaluated by the Ground Control Points (GCPs) in city area where GCPs were determined by GPS surveys, while in the mountain area with no GCPs, a 1:25,000 digital map was used. In order to minimize errors due to the inaccurate satellite orbit information and the phase unwrapping procedure, a Differential InSAR (DInSAR) was implemented in addition to the traditional InSAR analysis for DEM generation. In addition, DEMs from GTOPO30, SRTM-3, and 1:25,000 digital map were used for assessment the resolution of the DEM generated from DInSAR. 5-6 meters of elevation errors were found in the flat area regardless of the usage and the resolution of DEM, as a result of InSAR analyzing with a pair of ERS tandem and 6 pairs of JERS-1 interferograms. In the mountain area, however, DInSAR with DEMs from SRTM-3 and the digital map was found to be very effective to reduce errors due to phase unwrapping procedure. Also errors due to low signal-to-noise ratio of radar images and atmospheric effect were attenuated in the DEMs generated from the stacking of 6 pairs of JERS-1. SAR interferometry with multiple pairs of SAR interferogram with low resolution DEM can be effectively used to enhance the resolution of DEM in terms of data processing time and cost.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.20 no.9
• /
• pp.974-982
• /
• 2009

Photomixing techniques beating two optical signals with different wavelengths and strong correlations are also very useful techniques to make a continuous wave(CW) signals in the range of millimeter(mm) and terahertz(THz) frequencies. An optical double sideband-suppressed carrier(DSB-SC) technique is one of the popular techniques to generate two optical signals with different wavelengths and strong correlations. DSB-SC signals with strong correlations are generated by a CW modulation of an optical carrier with a local oscillator and an optical modulator. In the previous parers related the DSB-SC for producing the CW signals within the range of mm and THz frequencies, there have been no reports why the optical carrier should suppress. In order to clear that, we have analyzed and measured the characteristics of the mm-wave CW signals made by the DSB-SC photomixing in this paper. From our analysis and measurement results, compared with the case of the DSB with the maximized optical carrier, the power and phase noise have improved about 23.9 dB and 21 dBc/Hz(@ 1 MHz offset frequency) in the case of the DSB with the minimized optical carrier (that is to say, the DSB-SC). Consequently, it is evident reason that the optical carrier should sufficiently suppress to obtain the mm-wave CW signals with the high power and low noise. This paper has given very helpful data to make mm- and THz-wave CW signals using photomixing techniques with the DSB-SC because the reason why the optical carrier should be suppressed is reported in this paper based on the numerical and experimental results.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.19 no.3
• /
• pp.211-219
• /
• 2014

This paper proposes a low voltage high current LLC resonant converter for Green PC. Green PC is composed of a lot of blade PCs, and it is a centralized system to manage them in computer center. Green PC should require that its power supplies have several characteristics such as low output voltage, high output current, and high power conversion efficiency. Conventional PSFB (Phase Shift Full Bridge) converter is usually used as DC/DC converter for computer power supply because it has high power conversion efficiency thanks to ZVS (Zero Voltage Switching) operation under middle and high load conditions. However, this converter has some problems such as large switching noise and limitation of ZVS operation under light load condition. In order to improve the performance of power supply for Green PC, a new power supply using popular high efficiency LLC resonant converter for low voltage and high current application is proposed in this paper. The proposed power supply has ZVS capability over the entire load range, thus resulting in good efficiency and high switching frequency. Experimental results verify the performance of the proposed power supply for Green PC using 2[kW] (19[V], 105[A]) rated prototype converter.

• Geophysics and Geophysical Exploration
• /
• v.25 no.4
• /
• pp.177-188
• /
• 2022

Recently, the application of distributed acoustic sensors (DAS), which can replace geophones and seismometers, has significantly increased along with interest in micro-seismic monitoring technique, which is one of the CO₂ storage monitoring techniques. A significant amount of temporally and spatially continuous data is recorded in a DAS monitoring system, thereby necessitating fast and accurate data processing techniques. Because event detection and seismic phase picking are the most basic data processing techniques, they should be performed on all data. In this study, a machine learning-based P, S wave phase picking algorithm was developed to compensate for the limitations of conventional phase picking algorithms, and it was modified using a transfer learning technique for the application of DAS data consisting of a single component with a low signal-to-noise ratio. Our model was constructed by modifying the convolution-based EQTransformer, which performs well in phase picking, to the ResUNet structure. Not only the global earthquake dataset, STEAD but also the augmented dataset was used as training datasets to enhance the prediction performance on the unseen characteristics of the target dataset. The performance of the developed algorithm was verified using K-net and KiK-net data with characteristics different from the training data. Additionally, after modifying the trained model to suit DAS data using the transfer learning technique, the performance was verified by applying it to the DAS field data measured in the Pohang Janggi basin.

• The Transactions of the Korean Institute of Electrical Engineers P
• /
• v.60 no.2
• /
• pp.82-90
• /
• 2011

The small precision spindle motors in the high value-added products including the visible home appliances such as DLP projector require not only the energy conversion devices but also high efficiency, low vibration and sound operation. However, the spindle motors using the conventional ball bearing and sintered porous metal bearing have following problems, respectively: the vibration by the irregularity of balls and the short motor life cycle by the ball's abrasion and higher sound noises by dry contact between shaft and sleeve. In this paper, it is proposed that the spindle motor with a fluid dynamic bearing is suitable for the motor to drive the color wheel of the DLP(digital lightening processor) in the visible home appliances. The proposed spindle motor is composed of the fluid dynamic bearing with both the radial force and the thrust force. The fluid dynamic bearing is solved by the finite element analysis of the mechanical field with the Reynolds equations. The magnetic part of spindle motor, which is a type of Brushless DC Motor, is designed by the electro-magnetic field analysis coupled with the Maxwell equation. And the load capacity and the friction loss of fluid dynamic bearing are analyzed to bearing clearance variation by the fabrication error in designed motor. The design of the proposed motor is implemented by the load torque caused by the eccentricity and the unbalance of the fluid dynamic bearing when the motors are fabricated in error. The prototype of the motor with the fluid dynamic bearing is manufactured, and experiment results show the vibration, sound, and phase current at no load and color wheel load of the motors in comparison. The high performance characteristics with the low vibration, the low acoustic noise and the optimal mechanical structure are verified by the experimental results.

• Journal of IKEEE
• /
• v.11 no.1 s.20
• /
• pp.15-23
• /
• 2007

This paper describes a dual frequency synthesizer designed in a 0.2$\mu$m CMOS technology for wireless LAN applications. The design is focused mainly on low-power characteristics. Power dissipation is minimized especially in VCO and prescaler design. The designed synthesizer includes all building blocks for elimination of external components, other than the crystal. Its operating frequency can be programmed by external data. It operates in the frequency range of 2.3GHz to 2.7GHz (RF) and 250MHz to 800MHz (IF) and consumes 5.14mA at 2.5GHz and 1.08mA at 0.5GHz from a 2.5V supply. The measured phase noise is -85dBc/Hz in-band and -105dBc/Hz at 1MHz offset at IF band. The die area is 1.7mm$\times$1.7mm.

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.6 no.3
• /
• pp.154-161
• /
• 2006

This paper describes the new types of ngative differential resistance (NDR) IC applications which use a monolithic quantum-effect device technology based on the RTD/HBT heterostructure design. As a digital IC, a low-power/high-speed MOBILE (MOnostable-BIstable transition Logic Element)-based D-flip flop IC operating in a non-return-to-zero (NRZ) mode is proposed and developed. The fabricated NRZ MOBILE D-flip flop shows high speed operation up to 34 Gb/s which is the highest speed to our knowledge as a MOBILE NRZ D-flip flop, implemented by the RTD/HBT technology. As an analog IC, a 14.75 GHz RTD/HBT differential-mode voltage-controlled oscillator (VCO) with extremely low power consumption and good phase noise characteristics is designed and fabricated. The VCO shows the low dc power consumption of 0.62 mW and good F.O.M of -185 dBc/Hz. Moreover, a high-speed CML-type multi-functional logic, which operates different logic function such as inverter, NAND, NOR, AND and OR in a circuit, is proposed and designed. The operation of the proposed CML-type multi-functional logic gate is simulated up to 30 Gb/s. These results indicate the potential of the RTD based ICs for high speed digital/analog applications.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.24 no.7A
• /
• pp.1028-1035
• /
• 1999

To increase the throughput of data transmission in burst-mode TDMA communication systems and also to get a good BER performance at the same time, it is essential to rapidly acquire the carrier while keeping the desirable tracking performance. To achieve this goal, in this paper, a new decision-directed carrier recovery algorithm is presented. The proposed scheme does not incorporate the PLL and suppress the Gaussian random process of input noise by the pre-stage low pass filter so as to get both the fast acquisition and a good performance. Through computer simulations, the performance of the scheme is analyzed with respect to the acquisition time and bit error rate. The cycle slip in the proposed scheme is seldom observed at very low SNR environment in contrast to the previous proposed one. Because of this merit, it is not required to do the differential encoding and decoding in the proposed scheme.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.29 no.2C
• /
• pp.213-221
• /
• 2004

A new method for design of two-channel finite-impulse response(FIR) quadrature mirror-image filter(QMF) banks with low reconstruction delay using weighting function is proposed. The weighting function used in this paper is calculated from the previous updated filter coefficients vector which is adjusted from iteration to iteration in the design of QMF banks. In this paper, passband and stopband edge frequency are used in design of QMF banks with low delay characteristic in time domain instead of specific frequency interval where the artifacts occur in conventional design method. The investigation of specific frequency interval where artifacts occur can not be required by using passband and stopband edge frequency. Some comparisons of performance are made with other existing design method to demonstrate the proposed method for QMF bank design. and it was observed that the proposed method using the weighted function and passband and stopband edge frequency improves the peak reconstruction error by 0.001 [dB], the peak-to-peak passband ripple by 0.003[dB], SNR with a white noise by 7[dB] and SNR with a step input by 32[dB], but with a reduction of the computational efficiency because of updating the weighting function over the conventional method in Ref [11].