• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.35 no.6
• /
• pp.568-575
• /
• 2022

This paper is a study on frequency analysis and electronic noise reduction of energy storage system (ESS). We acquired 4 necessary data for about 2 minutes and 4 seconds using a sampling frequency of 10,000 Hz in ESS. Fast Fourier transform (FFT) was used for electronic noise analysis from the acquired data. As a result, it was confirmed that DC component, fundamental wave, second and higher harmonic component exist. For the attenuation of harmonics, low-pass filter (LPF) was applied. We confirmed that an attenuation of approximately 59.3% appears from the second harmonic. The presence of many harmonic components in the data of the ESS was expected to occur due to the insufficiency of optimization among the modules inside the ESS. Therefore, we propose that a national certification system for ESS should be introduced to settle down the issue properly.

• Journal of IKEEE
• /
• v.5 no.1 s.8
• /
• pp.16-23
• /
• 2001

Passive noise reduction is a classical approach to attenuate industrial noise, and an active noise cancellation has several advantages over the passive noise cancellation. The active noise reduction system offers a better low frequency performance with a smaller and lighter system. This paper presents a simple active closed loop control system which consists of an controller for inverting and compensating the phase delay, a microphone for picking up the external noise, and a loudspeaker for radiating the acoustic out of phase signal to reduce the external noise, and external noise can be reduced after compensating the phase difference to be $180^{\circ}$ in the frequency of maximum value in the amplitude response. The noise of the phase delay covered from $50^{\circ}\;to\;310^{\circ}$ tends to be reduced in the active noise control system and it is possible to obtain a noise cancelling of up to approximately 20[dB] at the ears in the enclosurer.

• Journal of electromagnetic engineering and science
• /
• v.11 no.4
• /
• pp.235-238
• /
• 2011

In this paper, a novel low phase noise voltage-controlled oscillator (VCO) using metamaterial structure and rat race coupler is presented for reducing the phase noise without the reduction of the frequency tuning range. The metamaterial structure has been realized by microstrip square open loop double split ring resonator (SRR). The rat race coupler shows slightly higher transmission compared to a Wilkinson combiner and is, therefore, used instead to improve the performances of VCO. By providing these unique modifications, the proposed push-push VCO has a phase noise of -126.30~-124.83 dBc/Hz at 100 kHz in the tuning range of 5.672~5.800 GHz.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2005.05a
• /
• pp.521-524
• /
• 2005

To protect a satellite and electronic equipment from the acoustic loads generated by rocket propulsion system, many launch vehicle use acoustic blanket. Most high frequency region of the acoustic loads is reduced by nose fairing skins and acoustic barrier, but low frequency region is not. In order to control low frequency acoustic mode, we designed away resonator panel which was made of composite materials. This paper shows the absorption coefficient measurement result of resonator and SPL(Sound Pressure Level) reduction by using resonators in a rectangular cavity for experiment. Proper arrangement of acoustic resonators at each mode reduce effectively SPL around the satellite through changing boundary condition.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2010.05a
• /
• pp.483-484
• /
• 2010

Unit cabin means room, which is installed in the high value ship such as drill ship and FPSO, after pre-assembled. In order to develop the noise control design for a unit cabin, a variety of acoustic tests such as sound absorption, transmission, and radiated noise measurements were carried out by using the mock-up of living quarter. From the tests, it was found out that the combined noise level of a unit cabin could be dominated by the radiated noise from wall panel in low frequency range and the design guidelines for the noise control of unit cabin were fully established, such as the improvement of sound transmission loss between the cabin and corridor, and radiated cabin noise reduction.

• Korean Journal of Construction Engineering and Management
• /
• v.15 no.2
• /
• pp.12-22
• /
• 2014

Recently, many people have been damaged seriously by construction noise. Accordingly, there have been increased the complaints and disputes. These complaints should be controlled strictly. Otherwise there could be delays or stops of project and losses of time and money. For this reasons, the Korean government is trying to convert from depending on the soundproof wall to noise control system focusing on noise sources. However, it is difficult to control the noise which is generated from construction site because construction equipment has very high noise level and construction noise generates temporarily and irregularly. Also, people do not know how much low frequency affect human body adversely because they cannot perceive low frequency noise easily. Hence, recently developed countries have conducted the research on the low frequency noise which damages on human physically and mentally. However, passive noise control is insufficient to reduce the low frequency noise, but only efficient to lower the high frequency noise. Thus, an approach which can complement limitations of passive noise control is needed. Therefore, the purpose of this research is to suggest the noise management model using active noise control on construction site. Also, ANC simulation has been conducted to examine its applicability on construction equipment. As a result, it is expected that there will be a reduction of construction noise and demages, as well as both mental and physical damages.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2004.10a
• /
• pp.729-732
• /
• 2004

An experimental and numerical approach has been carried out for to see the noise characteristics of a circular diamond saw. The noise level measurement result for the several kinds of shanks shows us that the noise level reduction in high frequency range could be an effective way to control the noise problem. Sandwich type shank whose center part is laminated with a low Young‘s modulus material greatly reduces the noise level. The noise level for the shank where several curve shaped slits are provided in the circumferential direction is reduced considerably too. The response spectrum analysis by the FEM shows us to be an alternative for predicting the noise characteristics of the shank.

• The Journal of the Acoustical Society of Korea
• /
• v.20 no.7
• /
• pp.13-20
• /
• 2001

The active noise cancellation system offers a better low frequency performance with a smaller and lighter system compared to a passive one. This paper presents an active noise control system capable of reducing the noise in a helmet after attenuating the external noise using the helmet as the passive noise reduction system, which consists of a controller for inverting and compensating the phase delay, a microphone for picking up the external noise, and a loudspeaker for radiating the acoustic anti-phase signal to reduce the external noise. In this paper, external noise can be reduced by noise controller by compensating the phase difference to be 180°in the frequency of maximun value in the amplitude response. The noise of the phase delay covered from 50°to 310°was reduced in this system and it is possible to obtain a noise reduction of up to approximately 20 dB at the ears in the enclosure.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2013.10a
• /
• pp.257-258
• /
• 2013

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.17 no.2
• /
• pp.294-301
• /
• 2017

This paper presents a low power ${\Sigma}{\Delta}$ modulator for an implantable chip to acquire a bio-signal such as EEG, DBS, and EMG. In order to reduce a power consumption of the proposed fourth order modulator, two op-amps utilized for the first two integrators are reconfigured to drive the second two integrators. The KT/C noise reduction circuit in the first two integrators is employed to enhance SNR of the modulator. The proposed circuit was fabricated in a 0.18 um CMOS n-well 1 poly 6 metal process with the active chip core area of $900um{\times}800um$ and the power consumption of 830 uW. Measurement results were demonstrated to be SNDR of 76 dB, DR of 77 dB, ENOB of 12.3 bit at the input frequency of 250 Hz and the clock frequency of 256 kHz. FOM1 and FOM2 were measured to be 41 pJ/step and 142.4 dB, respectively.