• Tribology and Lubricants
• /
• v.26 no.4
• /
• pp.224-229
• /
• 2010

A new test rig is presented to measure friction losses at journal bearings in a reciprocating compressor. This rig consists of a test bearing, torque sensor, driving motor and loading parts especially for vertical shaft. Friction losses are obtained by measuring torque between motor and test bearing. The experiments are carried out at several rotational speeds and temperatures. The test results are presented and discussed.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.59 no.1
• /
• pp.40-45
• /
• 2010

In order to establish the electric distribution system economically and operate efficiently, it becomes important to calculate energy losses of the system more accurately. This importance is not only related for the engineering of utilities' power network but also for the consumers' electric system. The Distribution Loss Factor (DLF) is the fundamental element of calculating the energy losses occurred through the electric system including the electric lines and equipments. Up to now, the DLF is calculated by empirical formulas using the correlation between the DLF itself and Load Factor. However, these methods have some limitations to reflect the various characteristics of the system and the load. In this regard, the novel method proposed here is developed to yield more accurate result of DLF which actively interacting with the characteristics and load patterns of the system. The improvement of accuracy is very significant according to the results of verification presented at the end of this paper.

• Journal of Applied Tourism Food and Beverage Management and Research
• /
• v.15 no.1
• /
• pp.127-136
• /
• 2004

This study was conducted to investigate the changes in physico-chemical characteristics of beef tenderloin steak by oven roasting at different internal temperatures. 1. Cooking time required for the internal temperatures of 60, 70 and $80^{\circ}$ of steaks were 15min, 23min and 28min, respectively, and standing time of cooked beef steaks were 10.5min at $60^{\circ}$, 9.4min at $70^{\circ}$ and 8.5min at $80^{\circ}$, respectively. 2. Total losses and evaporation losses were larges in cooked steaks at $60^{\circ}$ and $70^{\circ}$ than that of $80^{\circ}$ cooking. Total losses were 14.5% by cooking at $60^{\circ}$, 23.3% at $0^{\circ}$ and 26.6% at $80^{\circ}$ respectively. As internal temperature of meat was increased, moisture and fats content was decreased and protein content of meat was not changed.

• Proceedings of the KIPE Conference
• /
• 2000.07a
• /
• pp.376-379
• /
• 2000

This paper presents an improved ZVS partial series resonant DC/DC converter (PSRC) with low conduction losses suitable for high power and high frequency applications. The proposed PSRC have advantages of zero-voltage-swiching (ZVS) of main switches for entire load ranges and low conduction losses of main switches by decreasing current stresses Also the reduction of the effective duty cycle is not occurred during the resonant period of the main circuit because the auxiliary circuit of the proposed converter is placed out of the main power path. An improved ZVS PSRC has a so much characteristics with respect to the reduction of current stress. The operation principles of the proposed converter are explained in detail and the various simulated and experimental results show the validity of the proposed converter.

• Journal of Power Electronics
• /
• v.9 no.5
• /
• pp.708-717
• /
• 2009

In this paper a new zero voltage transition PWM bridgeless PFC is introduced. The auxiliary circuit provides soft switching condition for all semiconductor devices. Also, in the resonant path of the auxiliary circuit, only two semiconductor devices exist. Therefore the resonant conduction losses are low. Furthermore, the auxiliary circuit semiconductor elements consist of only one diode and one switch. The proposed auxiliary circuit is applied to a bridgeless PFC converter to further reduce conduction and switching losses. In this paper, the operating modes of this converter are explained and the resulting ideal and simulation waveforms are shown. The presented experimental results justify the theoretical analysis.

• Proceedings of the KIEE Conference
• /
• 2009.07a
• /
• pp.712_713
• /
• 2009

This paper deals with the analysis on eddy current looses of high speed permanent magnet synchronous motor (PMSM) for turbo compressor according to voltage source driving. This paper presents analytical procedures for calculation of the eddy current losses using Poynting theorem. On the basis of the magnetic vector potential and a two-dimensional (2-D) cylindrical coordinate system, this paper derived analytical solutions of the eddy current looses using phase current analysis. The eddy current losses of each harmonic obtained by fast Fourier transform (FFT) analysis of phase current are with results obtained from finite-element method (FEM).

• Proceedings of the KIEE Conference
• /
• 2009.07a
• /
• pp.758_759
• /
• 2009

In the design and analysis of electric machines the precise calculation of iron loss has incredible significance. It is tough to foresee iron losses precisely in machines due to distribution of non sinusoidal flux density. It is necessary to approximate the iron losses for the precise computation of efficiency. This paper presents a novel approach for the prediction of iron losses of the brushless dc (BLDC) motors by considering the effects of minor hysteresis loops in the simplified model. The novel iron loss model results are compared with the simplified model and with finite element method (FEM).

• Journal of Advanced Marine Engineering and Technology
• /
• v.22 no.3
• /
• pp.343-352
• /
• 1998

Higher frequency of energy transfer or at least energy conversion has to be used in order to reduce the size of inductors and capacitors required in the power supplies. Conventional PWM switching-mode power supplies have a limitation of operating frequency due to switching losses in the switching transistors and rectifier diodes. Means of reducing switching losses have been developed for high-frequency resonant amplifiers or more exactly dc/ac inverters. Because of smooth current and voltage waveforms resonant convertesrs havelower device switching losses and stresses lower electromagnetic interference(EMI) and lower noise than PWM converters. Therefore in this paper design equations of Classs E resonant low dv/dt rectifier with a series resonant capacitor drived using Fourier series techniques. The theory is compared with simulation results obtained for the rectifier operating at 10[MHz] ac input and 5[V] coutput.

• Proceedings of the KIEE Conference
• /
• 2007.10c
• /
• pp.47-49
• /
• 2007

This paper deals with the generating characteristic analysis of permanent magnet (PM) machines with multi-pole rotor and 3-phase stator windings considering losses such as copper loss, iron loss and mechanical loss. First, using d-q transformation, dynamic equations of PM machines are established. And then, characteristic equations for losses, power and efficiency are also derived. On the basis of d-q dynamic equations and characteristic equations, dynamic simulation algorithm is achieved by the MATLAB/SIMULINK. The simulation results are validated extensively by finite element (FE) analyses.

• Structural Engineering and Mechanics
• /
• v.2 no.1
• /
• pp.63-80
• /
• 1994

A cable is considered as a system of helical wires and a core with distributed dry friction forces at their interfaces. Deformations of the cable subjected to a uniform bending are analyzed. It is shown that there is a critical bending curvature when a slip at the wire-core interface occurs. It originates at the neutral axis of the cross section of the cable and then spreads symmetrically over the cross section with the increase of bending. The effect of slippage on the cable stiffness is investigated. This model is also used to analyze a cable under the quasi-static cyclic bending. Explicit expression for the hysteretic losses per cycle of bending is derived. Numerical examples are given to show the influence of dry friction and helix angle on the bending stiffness and hysteretic losses in the cable.