• Journal of Biosystems Engineering
• /
• 제34권2호
• /
• pp.114-119
• /
• 2009

Field test was conducted to investigate primary factors reducing rapeseed harvesting using a reciprocating cutter-bar of combine. The results showed that the correlation between crop moisture content and yield loss had a U-type, which indicated that the yield reduction increased at too high and too low crop moisture contents. The proper ranges of crop moisture contents were 27${\sim}$35%, 21${\sim}$56%, and 62${\sim}$73% in case of grain, pod and stem, respectively. Crop moisture content was negatively correlated with header loss, but positively correlated with threshing loss. In contrary, stem moisture content showed positive correlations with total loss, threshing loss and separation loss. Working speed was positively correlated with header loss. Total flow rate, pod flow rate and stem flow rate were highly correlated with threshing loss and separation loss. However, grain flow rate did not show any correlation with total loss. According to the principal component analysis, two principal components were derived as components with eigenvalues greater than 1.0. The contribution rates of the first and the second components were 52.7% and 38.9%, which accounted for 91.6% of total variance. As a contributive factor influencing total loss of rapeseed mechanical harvesting, a crop moisture content factor was greater than a crop flow rate factor. The stepwise multiple regression analysis for total loss was conducted using crop moisture content factor, crop flow rate factor and coefficient. However, the model did not show any correlation among independent and dependent factors ($R^2$=0.060).

• 전기학회논문지P
• /
• 제66권4호
• /
• pp.219-223
• /
• 2017

In this paper, we calculated the losses in the high voltage lines of power distribution system. The losses caused by high voltage lines are calculated using maximum current, resistance, loss factor, and dispersion loss factor. The accurate extraction of these factors are very important to calculate the losses exactly. Thus, the maximum loads are subdivided to regions and calculated monthly for more accurate maximum current calculation. Also, the composite resistance is calculated according to the ratio of the used wire types. In order to calculate the loss factor, the load factors according to the characteristics of each region were calculated. Finally, the losses of the distribution system is calculated by adding the losses by the transformers and the low voltage lines.

• 대한안전경영과학회지
• /
• 제16권3호
• /
• pp.23-34
• /
• 2014

With a view to analyzing the influential factors and their prioritization in association with the loss from construction disasters, this study has presented relative weighted value and importance for each category of loss by making a systematic classification of costs for non-insured categories (indirect costs) and conducting AHP analysis based on results of a survey of specialists. Through the study, first, I have divided the larger classification of loss factors into human loss factor, financial loss factor, special cost factor, and managerial loss factor, and, second, have presented prioritization of loss categories by allotting scores based on weighted values after calculating weighted value through pairwise comparison of loss levels. Based on these results of the study, we should be able to qualitatively calculate the loss costs that construction disasters inflict on business, promote rational decision-making and efficiency in spending related to a disaster, and compare it against safety investment designed to reduce disaster loss from the perspective of business strategy.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2005년도 춘계학술대회논문집
• /
• pp.279-282
• /
• 2005

The aim of this study is to suggest the method of measuring the dynamic stiffness and loss factor of materials used under floating floors in the dwelling by korea standard (KS F 2868). According to the results, the amplitude change of an impact source have no effect on the variation of the dynamic stiffness and loss factor. Comparing with the heating before, heating makes lower the dynamic stiffness except the EPS. In EVA material, the loss factor is increased by heating.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2014년도 추계학술대회 논문집
• /
• pp.960-965
• /
• 2014

Transmission loss of specimen is calculated by measuring energy of incident and transmission and using reverberant room of large size. But normal measurement of transmission loss has trouble because it is actually demanded that large area and specimen of certain size is satisfied with condition of diffused sound field. Especially, in case of mechanical component, interested frequency band is mid-frequency band between 500 ~ 2k Hz, and it is used to be available to minimize a reverberation chamber under conditions satisfying acoustic one because production of specimen for transmission loss measurement has limit. But, as in semi-reverberation room, it is difficult to satisfy condition of diffuse sound field and modification factor is applied to complement that. Correction factor when measuring transmission loss using semi-reverberation chamber is required accuracy because it works as main factor determining reliability of reuslts on transmission loss. In this study, it is analyzed that an effect on correction factor based on varying materials and sizes of specimens in order to deduction of it. Also It is confirmed that applied by elicited correction factor with actual railway vehicle's floor has reliability.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2004년도 추계학술대회 논문집 전력기술부문
• /
• pp.85-87
• /
• 2004

In the past, TR-cost was collected the combination of energy cost. When power market is restructured. TR-cost is collected the separated form of loss-cost, congestion-cost and maintenance-cost. One of thorn, loss-cost is computed by using TR loss-factor. We need correct and fair standards of loss factor to offer economical signal and to protect against confusions of investment and bidding. Therefore, we propose the method of minimizing system loss-cost that is based on fair and correct loss-factor.

• 농촌계획
• /
• 제11권2호
• /
• pp.9-19
• /
• 2005

The purpose of this study is to analyze the potential soil loss and hazard zone by the Revised Universal Soil Loss Equation(RUSLE) for preservation and management of land resources which is the base of ecosystem, and to grasp the relationship between RUSLE factors in the Nakdong River Basin. All thematic maps used in RUSLE are constructed through GIS and spatial analysis method derived from digital topographic maps, detailed soil maps, land-cover maps, and mean annual precipitation of 30 years collected respectively from National Geographic Information Institute, National Institute of Agricultural Science and Technology, and Ministry of Environment. The slope length of LS-factor that takes much times by the study area's wideness was calculated automatically through AML(Arc Macro Language) program developed by Van Remortel et al.(2001, 2003). The results are as follows; First, according to the soil loss estimation by the RUSLE, it shows that approximately 82% of the study area have relatively lower possibility of soil loss which is the 1 ton/ha in annual soil loss. While, 9.4% ($2,228km^2$) needed intensive and continuous management for soil loss. Because the amount of their annual soil loss was greater than 10 ton/ha that is optimum level suggested by Morgan(1995). For these areas, the author believe that a new approach which can minimize environmental impacts from soil loss through improvement of cultivation process and buffer forest zone should be applied. Second, according to the relationship between the RUSLE factors, topographical(LS-factor) and cover management(C-factor) conditions have a lot of influence on soil loss in case of the Nakdong River Basin. However, because of RUSLE factor's influence that affect to soil loss might be different based on the variety of spatial hierarchy and extent, it is necessary to analyze and evaluate factor's relationship in terms of spatial hierarchy and extent through field observations and further studies.

• 전자공학회논문지D
• /
• 제36D권3호
• /
• pp.75-84
• /
• 1999

주입전류가 문턱전류 이상일 때 선폭증가계수, 구속계수, 내부손실과 레이저의 길이가 λ/4 위상천이 DFB레이저의 단일모드 이득차와 발진주파수의 변화에 미치는 영향에 대하여 체계적으로 연구하였다. 구속계수나 선폭증가계수와 구속계수의 곱으로 주어지는 변수보다 선폭증가계수가 단일모드 이득차 및 발진주파수에 미치는 영향이 크다. 내부손실이나 레이저 길이 각각의 값보다 내부손실과 레이저 길이의 곱으로 정의되는 정규화된 내부손실이 DFB 레이저의 단일모드 이득차 및 발진주파수의 변화에 미치는 영향이 크다. 정규화된 내부손실이 같은 경우에는 내부손실계수보다 레이저의 길이가 동작특성에 미치는 영향이 큼을 알 수 있었다. 또한 양자우물 레이저가 builk 레이저에 비하여 선폭증가계수가 작기 때문에 구속계수와 정규화된 내부손실 값의 변화에 따른 단일모드 이득차의 감소와 발진주파수의 변화가 작음을 보았다.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2007년도 추계학술대회논문집
• /
• pp.824-828
• /
• 2007

In this paper Statistical Energy Analysis has been considered to predict middle, high frequency air borne interior noise. PIM method is used for verification. Damping loss factor and coupling loss factor have been derived from the response(SPL) of sub systems when the power is applied. The airborne SEA model of vehicle is modeled through AutoSea2. Insulation material's absorption coefficient and transmission loss are acquired from closed form solution and experiment.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2002년도 춘계학술대회논문집
• /
• pp.359-364
• /
• 2002

Statistical energy method is widely used for the prediction of vibrational and acoustical behavior of complex structures, such as ship building and automobile in mid-, high frequency ranges. However. in order to convince this SEA result, it is important to verify estimated SEA parameters, e. g. modal density, energy in each subsystem, damping loss factor, coupling loss factor. with possible other method. For modal density parameter, the experimental estimations via Experimental Modal Analysis are checked with those from finite element method for both beam- plate and plate-plate cans. Loss factors are calculated by Lyon's simple method for the two subsystem. finally. modal experiments are carried out by varying the mass added on the junction of two subsystem for the purpose of investigating the influence on the coupling loss factor's behavior.