• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 1997년도 춘계학술대회 논문집
• /
• pp.692-697
• /
• 1997

This paper presents a method of grinding and polishing automation of precision die after CNC machining. The method employs a robot system equipped with a pneumatic spindle and a special abrasive film pad. The robote program is automatically generated off-line from a PC and downloaded to robot controller. Position and orientation data for the program is supplied from cutter contact (CC) data of NC machining process. This eliminates separate robot teaching process. This paper aims at practical automation of die finishing process which is very time consuming and suffering from shortage of workpeople. Time loss for changeover from one product to next is eliminated by off-line programming exploiting appropriate NC machining data. Dextrous 6-axis robot with rigid wrist and simple tooling enables the process applicable to larger, rather complex 3 dimensional free surfaces

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2000년도 봄 학술발표회 논문집
• /
• pp.159-162
• /
• 2000

The purpose of this study is to develope an accurate procedure for measuring the glass content of fly ash produced by bituminous coal to assist in predicting their behavior in concrete. Quantitative mineralogical compositions of fly ashes were obtained by internal standard method using powder X-ray diffraction analysis. In the X-ray diffraction method, the specimen and standard fluorite were cautiously mixed and pulverized to 22$\mu$m in wet process so as to avoid the prefered orientation of the crystal and microabsorption effect of X-ray. calibration curve were fitted for several references peaks of four phases:$\alpha$-quartz. mullite, magnetite, hematite. The amount of glass was calculated by subtracting the amount of crystal phase and loss on ignition from the total amount. Glass content determined with this method ranged from 66.7 to 75.wt%.

• 한국해양공학회지
• /
• 제10권4호
• /
• pp.58-66
• /
• 1996

The purpose of this investigation is to estimate the strength with the variations of the notch shape and the adgesive condition at the fiber/matrix micro interface of E-glass/PP laminates. To promote the degradation of the adhesive condition at the fiber/matrix micro interface without matrix dissolution loss, low-, hot-wet and spiking tests were carried out. The absorpotion properties and the tensile properties were compared accrding to the fiber orientation and the content. The results show that, firstly, saturated moisture absorption was reached at 5cycles and their absorptions of RD-40, UD-42 and UD-50 are 0.68%, 0.63%, 0.60%, respectively. Secondly, all the specimens investigated were mostly degraded at 5cycle, whereas UD-50 having ellipse shaped notch the least decrement of strength.

• 대한치과의사협회지
• /
• 제50권6호
• /
• pp.322-328
• /
• 2012

Ectopic eruption of the permanent first molar is defined as the eruption of the tooth in an abnormal position or orientation. It may causes distal root resorption and premature exfoliation of the adjacent primary second molar and uncontrolled space loss is followed. Prolonged partial impaction of the permanent molar may also cause undetected caries or abscess formation of the neighbor teeth. The purpose of this paper is to provide a brief review regarding the etiology, classification, and different management techniques for correcting ectopic eruption of permanent first molar.

• Transactions on Electrical and Electronic Materials
• /
• 제7권2호
• /
• pp.67-71
• /
• 2006

In this paper, we have investigated the structure and dielectric properties of the $(Ba_{0.6}Sr_{0.4})TiO_3$ (BST) thin films fabricated on MgO(100)/Si substrate by an alkoxide-based sol-gel method. Both the structure and morphology of those films were analyzed by x-ray diffraction (XRD) and atomic force microscope (AFM). For the MgO(100)/Si substrate, the BST thin films exhibited highly (100) orientation. The highly (100)-oriented BST thin films showed high dielectric constant, tunability, and figure of merit (FOM). The dielectric constant, dielectric loss and tunability of the BST thin films annealed at $700^{\circ}C$ deposited on the MgO(100)/Si substrate measured at 10 kHz were 515.9, 0.0082, and 54.3%, respectively.

• 한국표면공학회지
• /
• 제28권6호
• /
• pp.343-351
• /
• 1995

Titanium nitride films have been prepared on various substrates (silicon wafer, HSS) by cathode arc ion plating process to measure microhardness, adhesion and wear-resistant behaviors by changing the substrate bias voltages (0∼-300V), thickness and roughness. Microhardnesses were measured by micro vickers hardness tester, the adhesion strengths were evaluated by acoustic signals through the scratch test with incremental applied load. As the substrate bias voltages were increased, the ｛111｝ orientation was predominant, the microhardnesses and adhesion strengths of tool steel were observed to be stronger than those of without subatrate bias voltage. Adhesion strengths of the substrate bias were 4-7 times higher than those of without the substrate bias, confirmed by SEM with EDX. Wear resistances were used pin-on-disk tribotester and TiN costing reduced the abrasive wear. As the substrate bias was increased, the weight loss and the friction coefficient was decreased.

• 센서학회지
• /
• 제16권4호
• /
• pp.301-306
• /
• 2007

AlN thin film for SAW filter application was deposited on (100) silicon wafers by reactive magnetron sputtering method. The structural characteristics were dependent on the deposition conditions such as sputtering pressure, RF power, substrate temperature, and nitrogen partial pressure. Scanning Electron Microscope (SEM), X-ray Diffraction (XRD), Electron Probe MicroAnalyzer (EPMA) and Atomic Force Microscope (AFM) have been used to find out structural properties and preferred orientation of AlN thin films. Insertion loss of SAW devices was 28.51 dB and out of band rejection was about 24 dB.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2002년도 금형가공 심포지엄
• /
• pp.95-102
• /
• 2002

With recent trends leaning towards product miniaturization, the advent of new material and speedy delivery times, old style conventional trial-and-error methods have been only serving to weaken corporate competitiveness. Reliant on tiny increments of time-consuming experience, this antiquated approach begets a delayed delivery of product development, cost loss and quality depreciation. To solve such problems, the Dedicated Injection Molding CAPA (Computer Aided Plastics Application) performs a preliminary examination on problems rising from every stage of creation - from appropriate material selection and mold design to mass production - through a computer system. Thus, it determines the optimum design variables and process conditions while diagnosing and solving defective molds.

• 한국측량학회:학술대회논문집
• /
• 한국측량학회 2009년도 춘계학술발표회 논문집
• /
• pp.129-132
• /
• 2009

Automatic target recognition surveying method is very important technology one-man surveying system. But in the case of loss of prism's position, it have to be re-tracking for searching it, consuming the searching time and complicated in processing. In this study, it is proposed new GPS receiver combination technology for orientation of both. In conclusion, the robotic TS(totalstation) is well assisted by absolute coordinates from single GPS receiver and multi-functional surveying instrument.

• Journal of information and communication convergence engineering
• /
• 제5권3호
• /
• pp.219-222
• /
• 2007

Highly conductive and transparent aluminum doped ZnO thin films (AZO) films have been prepared by r.f. magnetron sputtering processes on poly carbonate (PC) and onto glass as reference. In addition, the electrical, optical properties of the films prepared at various sputtering powers were investigated. The XRD measurements revealed that all of the obtained films were polycrystalline with the hexagonal structure and had a preferred orientation with the c-axis perpendicular to the substrate. The ZnO:Al films were increasingly dark gray colored as the sputter power increased, resulting in the loss of transmittance. High quality films with the resistivity as low as $9.7{\times}10^{-4}\;{\Omega}-cm$ and transmittance over 90% have been obtained by suitably controlling the r.f. power.