• Journal of Advanced Marine Engineering and Technology
• /
• 제13권3호
• /
• pp.26-36
• /
• 1989

Recently digital governor system is commonly adapted for the speed control of the marine diesel engine because of too much fluctuation of rpm resulted by the low speed, long stroke, high efficiency and a small number of cylinder of it, and versatile studies on the development of digital governor system are progressed. On this subject the new control method in which the fuel is controlled by feedforwarding the change of load as well as the feedback of angular velocity in case of disregarding the engine dead time and influence of scavenging air was proposed by the authors, and found the method has shown quite a good control performance in comparision to the conventional control method by the simulation using a digital computer for various load change. In this paper the speed control system of a diesel engine is simulated in case of regarding the engine dead time by the proposed method, and also confirm a good control performance of it under even more realistically simulated environment.

• 한국신뢰성학회지:신뢰성응용연구
• /
• 제13권1호
• /
• pp.55-63
• /
• 2013

For a reliability assessment of large machinery parts, reliable data should be obtained from testing many samples for a long time. However, in case of testing these samples, testing cost is excessive; in case of life test for long time, power consumption is high; and in case of accelerated test by over load, very high cost is required to build the life testing device. Especially it is very frequent that the expensive device's life has ended during a accelerated test by over load. In this study, the design mechanism of the life testing device which excels in energy saving during the reliability test of large machinery parts has been introduced.

• 한국초전도ㆍ저온공학회논문지
• /
• 제7권3호
• /
• pp.9-12
• /
• 2005

[ $Y_1Ba_2Cu_3O_{7-8}$ ] (YBCO) coated conductor has been fabricated by batch-type process using oxide-precursor-based metal-organic deposition (MOD) method. The batch-type process can be scaled up more simply to Produce long-length YBCO conductor than the reel-to-reel process. Also, it has less handling problems and is adequate to the ambient gas environment. In this work, YBCO oride powder was used as a starting precursor for MOD method. After reel-to-reel dip coating process, me ter-long-buffered metal tape was wound around a cylinder and underwent calcination and annealing processes. Annealed YBCO films showed good c-axis alignment and dense surface morphology with no cracks, but exhibited very low critical current density of $10^5\;A/cm^2$.

• 한국자동차공학회논문집
• /
• 제12권1호
• /
• pp.190-195
• /
• 2004

An exhaust brake system is composed of a gate valve, a pneumatic cylinder and an on-off solenoid valve. An on-off solenoid valve which is a key component of the exhaust brake system ought to have characteristics such as high reliability and long life for reducing the foot brake and tires damage, and for driver's fatigue relief of middle/large size vehicles running a long distance. In this paper, an on-off solenoid valve which is used for vehicle brake system was studied. For the performance evaluation of the on-off solenoid, electromagnetic characteristics and dynamic characteristics are analyzed. On the basic study for the performance improvement of exhaust brake system, pneumatic circuit and pneumatic valve of on-off solenoid type were suggested and the performance of pneumatic valve through the test procedure was evaluated.

• 한국지반신소재학회논문집
• /
• 제14권4호
• /
• pp.35-43
• /
• 2015

원형모형실험을 통해 철도노반재료로 사용되는 흙을 대상으로 함수비 변화에 따른 침하관계를 평가하였다. 초기 함수비에서 침하량비($R_e$)는 2.08이었으나, 초기함수비보다 2배 이상으로 함수비가 증가되었을 때 침하량비($R_e$)는 4.06으로 4배 이상의 침하가 발생하였다. 또한 실제 공용중인 콘크리트궤도에서 계측된 강우데이타를 기반으로 약 1년여간 현장에 매설된 함수비 측정장비를 통해 장기 함수비 변화추이를 관찰하였다. 콘크리트궤도의 직하부에 위치한 함수비는 강우강도에 따라 변화가 거의 없는 수준이며, 사면부에서는 최대 강우강도 20mm/hr가 초과되는 경우 약 4% 정도의 함수비 변화가 생기는 것을 볼 수 있다. 이러한 변화정도를 볼 때 콘크리트 궤도의 경우 배수성능이 적절히 유지된다면 노반 내부의 함수비 변화는 강우에 대하여 영향이 매우 미비할 것으로 판단된다.

• 한국잠사곤충학회지
• /
• 제44권1호
• /
• pp.13-18
• /
• 2002

한반도에 자생하는 돌뽕나무를 수집하여 그 형태학적 특성을 조사한 결과는 다음과 같다 1.체세포의 염색체수는 2n=84인 6배체이다. 2.웅화수는 3.6~6.0cm의 긴 원통형이고 무화주인 자화수의 길이는 18 mm로 왜소하고 자 색 또는 자홍색의 오디는 1.39~l .65 g이다. 3. 동동아는 가지에 비하여 매우 크고 부아는 존재하지 않는다. 4. 잎은 대형의 열엽 또는 전연엽이며, 피목 밀도는 9.42$\pm$1.29개/$\textrm{cm}^2$이다. 5. 잎의 모용 길이는 236~438$\mu\textrm{m}$이고, 이면에 밀도가높은 바 16~37개/25 $\textrm{mm}^2$분포한다. 6. 잎의 표면의 모용형태는 원추형, 이면의 것은 매우 세장한 원추형이다

• 대한조선학회지
• /
• 제11권1호
• /
• pp.9-16
• /
• 1974

To contribute towards more accurate estimation of the virtual inertia coefficient for the horizontal vibration of ships, three dimensional correction factor $J_H$ for the added mass of finitely long elliptic prismatic bars in horizontal vibration in a free surface of an ideal fluid are calculated. In the problem formulation Dr. T. Kumai's quasi-finite length concept[1,11,12] is employed. Now that, in Dr. Kumai's work[1] for the horizontal vibration the mathematical model was a circular cylinder, the principal aim of the authors' work is to investigate the influence of the beam-draft ratio B/T on $J_H$. The numerical results of this work are shown in Fig.3 graphically, from which we may recognize that the influence of B/T on $J_H$ is remarkable as much as that of the length-draft ratio L/T(refer to Fig.1 also). In Fig.3 the curves for B/T=2.00 are of those based on Dr. Kumai's result[1]. On the other hand, the experimental data obtained by Burril et al.[9] for the horizontal vibration of finitely long prismatic bars of various cross-section shapes are compared with the theoretical added mass coefficients defined by combination of the authors' $J_H$ from Fig.3 and two dimensional coefficients $C_H$ obtained by Lewis form approximation for the corresponding sections. They are in reasonable correspondence with each other as shown in Fig.2. Finally, considering that the longitudinal profile of full-form ship's hull is well resembled to that of an elliptic cylinder and that the influences of other factors such as the sectional area coefficient and the shape of section contour itself can be well merged in the two dimensional added mass coefficient, the authors recommend that the data given in Fig.3 may be successfully adopted for the three dimensional correction factor the added mass in the horizontal vibration of hull-form ships.

• 해양환경안전학회지
• /
• 제21권4호
• /
• pp.449-456
• /
• 2015

본 연구에서는 다양한 감쇠판을 원통형 부유체에 부착하고 수치 시뮬레이션을 통해 원통형 부유체의 heave RAO 및 고유주기의 변화를 고찰하였다. 먼저 감쇠판을 부착하지 않은 원통형 부유체의 heave RAO 및 고유주기를 파악하였고, 원통형 부유체에 부착한 감쇠판의 크기와 형상을 바꿔가며 각 경우에 대한 heave RAO 및 고유주기를 평가하였다. 수치 시뮬레이션 결과, 감쇠판의 모든 면적에 대해서 감쇠판을 부착한 원통형 부유체의 고유주기는 증가하였고, 감쇠판의 크기가 1.30D부터 입사파의 피크주기에서 heave RAO는 감소하였다. 감쇠판의 모든 면적에 대해서 원형 감쇠판이 Y자형 감쇠판보다 고유주기가 길게 나타나며, 고유주기의 차이는 감쇠판의 면적이 커질수록 그 차이가 커졌다. 운동응답 스펙트럼 계산 결과, 원형 감쇠판과 Y자형 감쇠판을 부착한 원통형 부유체의 heave 운동이 입사파의 피크주기에서 현저하게 감소하였다. 또한 원형 감쇠판을 부착한 원통형 부유체의 고유주기가 Y형 감쇠판을 부착한 경우보다 입사파의 피크 주기에서 더 멀리 이동하였다.

• 한국자동차공학회논문집
• /
• 제15권3호
• /
• pp.18-28
• /
• 2007

Three diesel engines were fueled with BDF 20, a blend of 80% diesel fuel and 20% biodiesel fuel by volume, and run in excess of 200 h to evaluate their combustion characteristics and durability. The engines used for this study were a 4-cylinder 2476-cc displacement IDI diesel engine(Engine 1), a 4-cylinder l732-cc displacement IDI diesel engine(Engine 2), and a single cylinder 673-cc displacement DI diesel engine(Engine 3). Engine dynamometer testing was performed on each engine at regularly scheduled intervals to monitor the performance and exhaust emissions, which were sampled at 1h intervals for analysis, The peak combustion pressure with BDF 20 increased in Engines 1 and 3 over that measured when burning pure diesel fuel, but that in Engine 2 remained constant. Combustion parameters, such as the maximum combustion pressure and corresponding crank angle, did not change over the long-term dynamometer testing. The BSFC with BDF 20 in Engine 1 was less than that measured with pure diesel fuel. The amount of smoke produced with BDF 20 was less for all engines ; the greatest reduction was observed for Engine 3. The NOx emissions were lower in the IDI engines than the DI engine. The traditional trade-off between smoke and NOx emissions was maintained for BDF 20 fuel for Engines 1 and 3. There was not a big difference in the $CO_2\;and\;O_2$ emissions for BDF 20, as compared to pure diesel fuel, but more $CO_2$ was exhausted by Engine 1 than by Engines 2 or 3 and less $O_2$ was exhausted by Engine 1 than by Engines 2 or 3. The engine parts remained clean, except for some carbon attached to the area surrounding the nozzle hole of the DI diesel engine.

• 수산해양기술연구
• /
• 제52권4호
• /
• pp.290-298
• /
• 2016

This study aims to reduce the force exerted to the buoy of the gillnet by wave and current. Five buoy models were selected for experiments and their rope tensions under wave and current action were compared. Five models were EL (ellipsoid), EL-H (ellipsoid-hole), SL (streamlined body), SP (sphere) and CL (cylinder, traditional type). In the first experiment, the Five models were tested without any attachment. In the second experiment, a flagpole was attached to each model. As a result, in the condition without flagpole, the tensions of four models with the exception of the CL were about a half of that of the CL. In the condition with flagpole, the tension of all models was twice larger than that without flagpole. Thus, a new model was suggested to improve the problem, which has a combined body that of a flagpole and a buoy Three new models of CL-L (long and thin cylinder), LF (leaf shape) and LF-F (leaf shape with fin) were designed. Also a cylinder type (CLD) with a flagpole as a control was included in the experiment. As a result, the LF-F had the smallest tension and a half tension of the CLD. Therefore, it is supposed that the flagpole and buoy combined model could reduce the tension on buoy rope and contribute to improve the gillnet loss problem.