• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.30 no.7C
• /
• pp.624-632
• /
• 2005

We consider an adaptive bit-loading technique for bit interleaved coded modulation-orthogonal frequency division multiplexing(BICM-OFDM) systems. By adjusting transmission parameter of each subcarrier adaptively depending on the subchannel state, the performance of OFDM system can be improved dramatically. In this paper, the number of bits for each subcarrier is allocated to minimize bit error rate keeping the constant throughput for the adaptive transmission technique of BICM-OFDM system which can be applied to real time transmission. Also, We use the discrete Lagrange multiplier method to get the optimum solution under the integer bit allocation constraint. Simulation results show that computational amount of the proposed bit allocation technique is not high and BICM-OfDM system using the proposed technique can get the SNR gain by 2$\~$3 dB over nonadaptive one.

• Nuclear Engineering and Technology
• /
• v.49 no.1
• /
• pp.245-253
• /
• 2017

The relative displacement of a piping system installed between isolated and nonisolated structures in a severe earthquake might be larger when without a seismic isolation system. As a result of the relative displacement, the seismic risks of some components in the building could increase. The possibility of an increase in seismic risks is especially high in the crossover piping system in the buildings. Previous studies found that an elbow which could be ruptured by low-cycle ratcheting fatigue is one of the weakest elements. Fatigue curves for elbows were suggested based on component tests. However, it is hard to find a quantitative evaluation of the ultimate state of piping elbows. Generally, the energy dissipation of a solid structure can be calculated from the relation between displacement and force. Therefore, in this study, the ultimate state of the pipe elbow, normally considered as failure of the pipe elbow, is defined as leakage under in-plane cyclic loading tests, and a failure estimation method is proposed using a damage index based on energy dissipation.

• Steel and Composite Structures
• /
• v.22 no.6
• /
• pp.1217-1238
• /
• 2016

Mega composite structure systems have been widely used in high rise buildings in China. Compared to other structures, this type of composite structure systems has a larger cross-section with less weight. Concrete filled steel tubular (CFST) laced column to box-beam connections are gaining popularity, in particular for the mega composite structure system in high rise buildings. To enable a better understanding of the destruction characteristics and aseismic performance of these connections, three different connection types of specimens including single-limb bracing, cross bracing and diaphragms for core area of connections were tested under low cyclic and reciprocating loading. Hysteresis curves and skeleton curves were obtained from cyclic loading tests under axial loading. Based on these tested curves, a new trilinear hysteretic restoring force model considering rigidity degradation is proposed for CFST laced column to box-beam connections in a mega composite structure system, including a trilinear skeleton model based on calculation, law of stiffness degradation and hysteresis rules. The trilinear hysteretic restoring force model is compared with the experimental results. The experimental data shows that the new hysteretic restoring force model tallies with the test curves well and can be referenced for elastic-plastic seismic analysis of CFST laced column to composite box-beam connection in a mega composite structure system.

• Journal of Pharmaceutical Investigation
• /
• v.30 no.4
• /
• pp.253-258
• /
• 2000

In order to design the oral vaccine delivery system, we prepared the alginate micro spheres containing GFP (green fluorescent protein) as a model drug by spray method. To optimize the preparation conditions of microspheres, we investigated the effects of various parameters including nozzle pressure, nozzle opening angle, and concentrations of sodium alginate and calcium chloride. The prepared microspheres were evaluated by measuring their sizes, loading efficiency, and morphology. The particle size of microspheres was affected by the concentration of sodium alginate and calcium chloride, nozzle pressure, and nozzle opening angle. As the concentration of sodium alginate increased, GFP loading efficiency and particles size of microsphere also increased. However, it was observed to be difficult to spray the sodium alginate solution with concentration greater than 1.5% (w/v), due to high viscosity. The pressure over $3\;kgf/cm^2$ didn't affect the size of particles. As a result, the spraying method enabled us to prepare microspheres for oral vaccine delivery system. In this study, microspheres prepared with 1% (w/v) sodium alginate had greater loading efficiency and better spherical shape.

• Membrane and Water Treatment
• /
• v.10 no.4
• /
• pp.265-275
• /
• 2019

This study aimed to develop a compact partial nitritation step by forming granules with high Ammonia-Oxidizing Bacteria (AOB) fraction using the Air-lift Granulation Reactor (AGR) and to evaluate the feasibility of treating reject water with high ammonium content by combination with the Anammox process. The partial nitritation using AGR was achieved at high nitrogen loading rate ($2.25{\pm}0.05kg\;N\;m-3\;d^{-1}$). The important factors for successful partial nitritation at high nitrogen loading rate were relatively high pH (7.5~8), resulting in high free ammonia concentration ($1{\sim}10mg\;FA\;L^{-1}$) and highly enriched AOB granules accounting for 25% of the total bacteria population in the reactor. After the establishment of stable partial nitritation, an effluent $NO_2{^-}-N/NH_4{^+}-N$ ratio of $1.2{\pm}0.05$ was achieved, which was then fed into the Anammox reactor. A high nitrogen removal rate of $2.0k\; N\;m^{-3}\;d^{-1}$ was successfully achieved in the Anammox reactor. By controlling the nitrogen loading rate at the partial nitritation using AGR, the influent concentration ratio ($NO_2{^-}-N/NH_4{^+}-N=1.2{\pm}0.05$) required for the Anammox was controlled, thereby minimizing the inhibition effect of residual nitrite.

• The Journal of Korea Institute of Information, Electronics, and Communication Technology
• /
• v.14 no.1
• /
• pp.43-47
• /
• 2021

This paper investigates the network throughput of PLC (Power Line Communication) system in the in-building network. The OFDM (Orthogonal Frequency Division Multiplexing) modulation format and adaptive bit loading algorithm is used to minimize the effect of signal loss and noise on transmission performance in the power line channel characterized by frequency selective fading. The network throughput of the PLC system which consists of gateway and CPE（Customer Premise Equipment) PLC modem in the in-building network is measured by network performance measurement tool, iperf and analyzed according to the TCP (Transmission Control Protocol) window size.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.17 no.1
• /
• pp.187-192
• /
• 2022

In the current container port, the containers standardized by the automated operating system using the latest information and communication technology are systematically made according to the optimal stowage planning. However, loading of steel coils with a unit weight of several tens of tons is still performed manually, which is very inefficient. As a result, work is delayed and safety accidents occur frequently. In this study, an automated simulation system for loading steel coils was designed to prevent misjudgment, congestion, and safety accidents that occur during the manual loading process of steel coils.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.13 no.1 s.53
• /
• pp.205-213
• /
• 2009

This study was planned to develop monitoring system of cable force to resolve cable force of cable-stayed bridge efficiently in a long-term plan. In the proposed monitoring system, firstly data are sampled from real-time acceleration record, secondly these sampled data are frequency analyzed by using the FFT(Fast Fourier Transform) algorism and lastly the analyzed results are averaged and generalized. For evaluating the applicability of this monitoring system, field loading test has performed in real cable-stayed bridge. In comparison with cable force by field manual calculation and cable force of monitoring system by semi-automatic calculation, the difference of calculated cable forces has within 1% error range and it is acceptable range. Additionally within negligible 5% error range of difference has occur between field manual calculation and monitoring system by automatic calculation. so monitoring system in this study has been verified to be reliable.

• Journal of the Korean Society of Safety
• /
• v.31 no.6
• /
• pp.52-57
• /
• 2016

In this study, a restoring viscous damper is introduced for X-type damper system which is designed for the seismic response control of large spatial structures. A nonlinear numerical model for its behavior is developed using the result of dynamic loading tests. The X-type damper system is composed of restoring viscous dampers and connecting devices such as adjustable wire bracing, where the damping capacity of the system is controllable by changing the number of the dampers. The restoring viscous damper is devised to exert main damping force in tension direction, which is effective to prevent the buckling of bracing subjected to compressive axial force. To evaluate the performance of the proposed damper, dynamic cyclic loading tests are performed by using manufactured dampers at full scale. In order to construct the numerical model of the damper system, its model parameters are first identified using a nonlinear curve fitting method with the test data. The numerical simulations are then performed to validate the accuracy of the numerical model in comparison with the experimental test results. It is expected that the proposed system is effectively applicable to various building structures for seismic performance enhancement.

• KOREAN JOURNAL OF PACKAGING SCIENCE & TECHNOLOGY
• /
• v.26 no.1
• /
• pp.11-17
• /
• 2020

This study conducted a case study and a questionnaire analysis in parallel. In the case study, a study was conducted on domestic manufacturer A by analyzing pallet loading efficiency of RRP(Retail Ready Packaging) products and pallet loading efficiency of MWC(Membership Wholesale Club) delivered products. As a result of the pallet loading efficiency simulation of 50 RRP products of Manufacturer A, it was 80.0% based on the T-11 type pallet and 84.3% based on the T-12 type pallet. It was found It refers that the route of producing the product from the manufacturer A and delivering it to the MWC A in the form of RRP resulted in the decrease of the pallet loading efficiency through the change of the loading pattern and the adjustment of the number of loads. As a result of analyzing the questionnaire about whether the overall efficiency of the supply chain will be improved if the operation of the packaging system considering the SCM(Supply Chain Management) aspect is χ² = 178.500, there was a statistically significant difference at the significance level of 0.000. Manufacturers and logistics companies answered "yes" the most, but distributors answered "is average" the most, confirming that the packaging can be constructed with the highest operational efficiency. Therefore, as a result of confirming the impact of packaging design considering the SCM aspect on logistics efficiency, it indicates the importance of closer collaboration between manufacturers and distributors.