• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.41 no.11
• /
• pp.1574-1579
• /
• 2016

This paper presents a self-powered sensor-node scheme using a RF wireless power harvesting techniques for improve drone time of flight. Sensor-node that is proposed is turned when two conditions satisfy: The one is input RF ID data from master-node should be same with sensor-node's ID, and the other one is RF wireless power harvesting system is turned on by hysteresis switch. In this paper, master-node's output is 26 dBm at 263 MHz. Maximum RF to DC power conversion efficiency is about 55% at 4-6 dBm input power condition (2 meter from master-node). The maximum RF wireless power harvesting range is about 13 meter form master-node. And power consumption of the sensor-node's load elements such as transmitter, MCU and temperature sensors is approximately average 15 mA at 5.0 V for 10 msec.

• Journal of KIISE:Software and Applications
• /
• v.32 no.4
• /
• pp.258-267
• /
• 2005

We propose the ubiFloor system to track and recognize users in ubiquitous computing environments such as ubiHome. Conventional user identification systems require users to carry tag sensors or use camera-based sensors to be very susceptible to environmental noise. Though floor-type systems may relieve these problems, high cost of load cell and DAQ boards makes the systems expensive. We propose the transparent user identification system, ubiFloor, exploiting user's walking pattern to recognize the user with a set of simple ON/OFF switch sensors. The experimental results show that the proposed system can recognize the 10 enrolled users at the correct recognition rate of $90\%$ without users' awareness of the system.

• Korean Journal of Applied Biomechanics
• /
• v.21 no.3
• /
• pp.327-334
• /
• 2011

The objective of this study was to develop a scientific approach for investigating Korean dance in detail, and to examine the intense expressions and various movements, which are based on Danjeon breathing. For the purpose, we analyzed the movement changes and distribution of forces resulting from the switch in movement between exhalation and inhalation while bending, which is the most basic movement in Korean dance. The following conclusions were drawn from this study. In Korean dance, bending with breathing involves less back-and-forth-movement and more up-and-down movement, as compared to bending without breathing; this indicates greater body stability and a wider range of movements while bending with breathing. In addition, less time is required for bending with breathing at the point of switching from exhalation to inhalation, and it involves less movement of the supporting leg; thus, vending with breathing involves faster switching from bending movements to extending movements. While bending, the raised leg goes through a less smooth curve while breathing, which indicates stronger movement of the toes. Bending with breathing requires a greater braking force than bending without breathing, and the vertical force, generated by switching from exhalation to inhalation, is transferred to extending movements using the ground load. The results of this study can be potentially employed to investigate the expressions used in Korean dance on th basis of its principle of forces. Korean dance has evolved into various creative forms, and basic analytical studies of these diverse forms and related breathing methods re required in the future.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.13 no.2
• /
• pp.110-118
• /
• 2008

The regulated peak power tracking (RPPT) systems such as the series structure and the parallel structure are commonly used in the satellite space power system. However, this structure processes the solar array power to the load through two regulators during one orbit cycle, which reduces the energy transfer efficiency. The series-parallel structure for the RPPT system can improve the power conversion efficiency, but an additional regulator increases the cost, size and weight of the system. In this paper, a simplified series-parallel space power system that consists of two regulators is proposed. The proposed system has the similar energy transfer efficiency with the series-parallel structure by adding one switch to the series structure, which reduces the cost, size and the weight. The large signal stability analyses is provided to understand the four main modes of system operation. In order to compare the energy efficiency with a series structure, the simulation is performed. The experimental verifications are performed using a prototype hardware with TMS320F2812 DSP and 200W solar arrays.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.17 no.6
• /
• pp.486-494
• /
• 2012

In this paper, we proposes the three-phase embedded Z-source inverter consisting of the three embedded Z-source converters and it's the output voltage control method. Each embedded Z-source converter can produce the bipolar output capacitor voltages according to duty ratio D such as single-phase PWM inverter. The output AC voltage of the proposed system is obtained as the difference in the output capacitor voltages of each converter, and the L-C output filter is not required. Because the output AC voltage can be stepped up and down, the boost DC converter in the conventional two-stage inverter is unnecessary. To confirm the validity of the proposed system, PSIM simulation and a DSP based experiment were performed under the condition of the input DC voltage 38V, load $100{\Omega}$, and switching frequency 30kHz. Each converter is connected by Y-connection for three-phase loads. In case that the output phase voltage is the same $38V_{peak}$ as the input DC voltage and is the 1.5 times($57V_{peak}$), the simulation and experimental results ; capacitor voltages, output phase voltages, output line voltages, inductor currents, and switch voltages were verified and discussed.

• Journal of Power Electronics
• /
• v.17 no.1
• /
• pp.222-231
• /
• 2017

In this paper, a new architecture for a cost-effective power conditioning systems (PCS) using a single-sourced asymmetric cascaded H-bridge multilevel inverter (MLI) for photovoltaic (PV) applications is proposed. The asymmetric MLI topology has a reduced number of parts compared to the symmetrical type for the same number of voltage level. However, the modulation index threshold related to the drop in the number of levels of the inverter output is higher than that of the symmetrical MLI. This problem results in a modulation index limitation which is relatively higher than that of the symmetrical MLI. Hence, an extra voltage pre-regulator becomes a necessary component in the PCS under a wide operating bias variation. In addition to pre-stage voltage regulation for the constant MLI dc-links, another auxiliary pre-regulator should provide isolation and voltage balance among the multiple H-bridge cells in the asymmetrical MLI as well as the symmetrical ones. The proposed PCS uses a single-ended DC-DC converter topology with a coupled inductor and charge-pump circuit to satisfy all of the aforementioned requirements. Since the proposed integrated-type voltage pre-regulator circuit uses only a single MOSFET switch and a single magnetic component, the size and cost of the PCS is an optimal trade-off. In addition, the voltage balance between the separate H-bridge cells is automatically maintained by the number of turns in the coupled inductor transformer regardless of the duty cycle, which eliminates the need for an extra voltage regulator for the auxiliary H-bridge in MLIs. The voltage balance is also maintained under the discontinuous conduction mode (DCM). Thus, the PCS is also operational during light load conditions. The proposed architecture can apply the module-integrated converter (MIC) concept to perform distributed MPPT. The proposed architecture is analyzed and verified for a 7-level asymmetric MLI, using simulation results and a hardware implementation.

• Journal of Korea Society of Industrial Information Systems
• /
• v.17 no.1
• /
• pp.31-38
• /
• 2012

Next generation cellular applications and smart phone usage generate very heavy wireless data traffic. It becomes ineluctable for mobile network operators to have multiple core network entities such as Serving Gateway and Packet Data Network Gateway in 4G-LTE to share this high traffic generated. A typical configuration consists of multiple serving gateways behind a load-balancer which would determine which serving gateway would service a end-users'request. Such hardware is expensive, has a rigid policy set, and is a single point of failure. Another perspective of today's increasingly high data traffic is that besides it is being widely accepted that the high bandwidth L TE provides is creating bottlenecks for service providers by the increasing user bandwidth demands without creating any corresponding revenue improvements, a hidden problem that is also passively advancing on the newly emerging 4G-LTE that may need more immediate attention is the network signaling traffic, also known as the control-plane traffic that is generated by the applications developed for smartphones and tablets. With this as starting point, in this paper, we propose a solution, by a new approach considering OpenFlow switch connected to a controller, which gains flexibility in policy, costs less, and has the potential to be more robust to failure with future generations of switches. This also solves the problem of scaling the control-plane traffic that is imperative to preserve revenue and ensure customer satisfaction. Thus, with the proposed architecture with OpenFlow, mobile network operators could manipulate the traffic generated by the control-plane signaling separated from the data-plane, besides also reducing the cost in installing multiple core-network entities.

• Journal of the Institute of Electronics Engineers of Korea TE
• /
• v.37 no.5
• /
• pp.11-116
• /
• 2000

A topology decreased switching loss and voltage stress by zero voltage switching is presented in this paper. Generally, Switching mode converting productes voltage stress and power losses due to excessive voltage and current. which affect to performance of power supply and reduce overall efficiency of equipments. Virtually, In flyback converter, transient peak voltage and current at switcher are generated by parasitic elements. To solve these problems, present ZVS flyback converter topology applied a auxiliary circuit. Incorporation of auxiliary circuit into a conventional flyback topology serves to reduce power losses and to minimize switching voltage stress. Snubber capacitor in auxiliary circuit serves ZVS state by control voltage variable time at turn on and off of main switch, then reduces voltage stress and power losses. The proposed converter has lossless switching in variable load condition with wide range. A detailed analysis of the circuit is presented and the operation procedure is illustrated. A (50W 100kHz prototype) ZVS flyback converter using a auxiliary circuit is built which shows an efficiency improvement as compared to a conventional hard switching flyback converter.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2012.10a
• /
• pp.255-258
• /
• 2012

In this paper, with a thermoelectric device using the seebeck effect which generates electromotive force by temperature difference generates electric energy an energy harvesting circuit using MPPT(Maximun Power Point Traking) control is designed. After periodically sampling the open voltage of the thermoelectric device, the 1/2 voltage of open voltage which in a maximum power point is maintained through MPPT control circuit and harvested energy from thermoelectric device is delivered to load through a switch. The proposed thermal energy harvesting circuit is designed with $0.35{\mu}m$ CMOS process and the chip area excluding pads is $1168.7{\mu}m{\times}541.3{\mu}m$.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.5 no.2
• /
• pp.154-162
• /
• 2000

A technique to suppress the low frequency ripple voltage of the DC output ${\gamma}$oltage in three-phase buck d diode rectifiers is presented in this paper. The proposed pulse frequency modulation method is employed to r regulate the output voltage of the buck diode rectifiers and guarantee zero-current switching of the switch over the Vvide load range. The pulse frequency control method used in tIns paper shows generally good p performance such as low THD of the input line current and unity power factor. In addition, the pulse f freιluency method can be effectively used to suppress the low frequency voltage ripple appeared in the dc output voltage. The proposed technique illustrates its validity and effectiveness through the respective s simulations and experiments.