• Smart Structures and Systems
• /
• v.2 no.3
• /
• pp.275-293
• /
• 2006

For health monitoring purpose usually the structure is instrumented with a large scale and multichannel measurement system. In case of highway bridges, operating vehicle could be utilized to reduce the number of measuring devices. First this paper presents a static damage detection algorithm of using operating vehicle load. The technique has been validated by finite element simulation and simple laboratory test. Next the paper presents an approach of using this technique to field application. Here operating vehicle load data has been used by instrumenting the bridge at single location. This approach gives an upper hand to other sophisticated global damage detection methods since it has the potential of reducing the measuring points and devices. It also avoids the application of artificial loading and interruption of any traffic flow.

• Journal of Aerospace System Engineering
• /
• v.7 no.2
• /
• pp.8-14
• /
• 2013

When launch vehicles are manufactured, one of the key points is a design of lightweight structure for reducing costs. Isogrid structure was designed to solve this topic, and many researches were carried out about buckling load because compression load is mainly applied to them. Recently, many studies are also being carried out about FEM model geometry of isogrid structure. The reason is that isogrid structure depends on size of ribs so it is difficult to modify about small changes in rib pattern. In this study, 1/8 model of cylindrical isogrid structure model was developed to analyze buckling behavior. Through parameter study, buckling analysis were performed to analyze buckling load and buckling mode depending on size of ribs.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2009.09a
• /
• pp.145-156
• /
• 2009

Large diameter bored pile was selected as the foundation type for Taipei 101. The pile construction method and specific construction procedures were determined based on the results of trial installation and pile load tests. The baseline for foundation design was established using the friction versus depth characteristics of each ground layer obtained from the pile load tests. As the ground profile and depth to the top of rock formation varied significantly on this site, the pile length, bearing capacity and settlement for single pile were analyzed using the information interpreted from adjacent boreholes. The post grouting at pile tip was mandatory for pile construction. Nevertheless, it was treated as a measure reducing the influence of construction uncertainties and providing extra safety for the foundation system.

• Progress in Superconductivity and Cryogenics
• /
• v.16 no.2
• /
• pp.47-53
• /
• 2014

In this paper, the general electromagnetic design process of a 10-MW-class high-temperature superconducting (HTS) synchronous generator that is intended to be utilized for large scale offshore wind generator is discussed. This paper presents three-dimensional (3D) electromagnetic design proposal and electrical characteristic analysis results of a 10-MW-class HTS synchronous generator for wind power. For more detailed design by reducing the errors of a two-dimensional (2D) design owing to leakage flux in air-gap, we redesign and analyze the 2D conceptual electromagnetic design model of the HTS synchronous generator using 3D finite element analysis (FEA) software. Then electrical characteristics which include the no-load and full-load voltage of generator, harmonic contents of these two load conditions, voltage regulation and losses of generator are analyzed by commercial 3D FEA software.

• Wind and Structures
• /
• v.35 no.5
• /
• pp.353-368
• /
• 2022

Wind turbine blades are adjusted in real-time according to the wind conditions and blade deformations to improve power generation efficiency. It is necessary to predict and reduce the aeroelastic deformations of wind turbine blades. In this paper, the equivalent model of the blade is established by the finite element method (FEM), and the aerodynamic load of the blade is evaluated based on the blade element momentum (BEM) theory. The aeroelastic coupling model is established, in which the bending-torsion coupling effect of the blade is taken into account. The steady and dynamic aeroelastic deformations are calculated. The influences of the blade section's shear centre position and the blade's sweepback design on the deformations are analyzed. The novel approaches of reducing the twist angle of the blade by changing the shear centre position and sweepback of the blade are presented and proven to be feasible.

• Journal of Information Processing Systems
• /
• v.2 no.1
• /
• pp.39-43
• /
• 2006

In this paper, we proposed TASL-MAC, a medium-access control (MAC) protocol for wireless sensor networks. In wireless sensor networks, sensor nodes are usually deployed in a special environment, are assigned with long-term work, and are supported by a limited battery. As such, reducing the energy consumption becomes the primary concern with regard to wireless sensor networks. At the same time, reducing the latency in multi-hop data transmission is also very important. In the existing research, sensor nodes are expected to be switched to the sleep mode in order to reduce energy consumption. However, the existing proposals tended to assign the sensors with a fixed Sleep/Listening schedule, which causes unnecessary idle listening problems and conspicuous transmission latency due to the diversity of the traffic-load in the network. TASL-MAC is designed to dynamically adjust the duty listening time based on traffic load. This protocol enables the node with a proper data transfer rate to satisfy the application's requirements. Meanwhile, it can lead to much greater power efficiency by prolonging the nodes' sleeping time when the traffic. We evaluate our implementation of TASL-MAC in NS-2. The evaluation result indicates that our proposal could explicitly reduce packet delivery latency, and that it could also significantly prolong the lifetime of the entire network when traffic is low.

• Journal of the Korean Institute of Gas
• /
• v.20 no.3
• /
• pp.73-77
• /
• 2016

This paper presents the displacement behavior safety of hollow shafts with an equivalent volume for various cross sectional area using a finite element method. The FEM results indicate that the hollow shafts with X-type or Y-type columns between outer tube, middle tube and inner tube may reduce a maximum displacement at the middle length of hollow shafts. Especially, the load-bearing column of X-type or Y-type hollow shaft is directly connected between outer tube and inner tube without a shift for reducing the vertical displacement. And increased thickness of a load-bearing column is recommended for reducing the vertical displacement and increasing the displacement behavior safety for an equivalent volume of a hollow shaft.

• Journal of Korea Multimedia Society
• /
• v.7 no.2
• /
• pp.272-282
• /
• 2004

As Web services need to manage lots of information, it is indispensable to reduce server's load and speed up processing time. In this paper, we analyze the loading problems of server and suggest designing methods for light loaded Web applications based on .NET. The proposed methods include using a relative database to produce minimized modules and Stored Procedures to simplify SQL statements for reducing sever's load. Web pages are organized with scripts replacing server language, which improve server's capability by reducing loads. The execution time is also speeded up by organizing Web pages with User Controls. And XML/EDI is used for managing the effective exchange of documents. The proposed methods are implemented as an education management system and shows its effectiveness.

• Journal of Positioning, Navigation, and Timing
• /
• v.9 no.3
• /
• pp.285-292
• /
• 2020

This paper introduces a new computational efficient Dilution of Precision (DOP)-based landmark exclusion method while ensuring the safety of the LiDAR-based navigation system that uses an innovation-based Nearest-Neighbor (NN) Data Association (DA) process. The NN DA process finds a correct landmark association hypothesis among all potential landmark permutations using Kalman filter innovation vectors. This makes the computational load increases exponentially as the number of landmarks increases. In this paper, we thus exclude landmarks by introducing DOP that quantifies the geometric distribution of landmarks as a way to minimize the loss of integrity performance that can occur by reducing landmarks. The number of landmarks to be excluded is set as the maximum number that can satisfy the integrity risk requirement. For the verification of the method, we developed a simulator that can analyze integrity risk according to the landmark number and its geometric distribution. Based on the simulation, we analyzed the relationship between DOP and integrity risk of the DA process by excluding each landmark. The results showed a tendency to minimize the loss of integrity performance when excluding landmarks with poor DOP. The developed method opens the possibility of assuring the safety risk of the Lidar-based navigation system in real-time applications by reducing a substantial amount of computational load.

• Korean Journal of Pharmacognosy
• /
• v.14 no.4
• /
• pp.197-200
• /
• 1983

This study is concerned with quality and analysis of nutritive value of commercially available honey and pollen load. Of thirteen kind of commercially available honeys, acid levels were less than KP IV standard. Color reaction for ammonia, resorcine and varium chloride was negative and trace of starch and dextrine was not detected. There were no extraneous materials in honey samples. Specific gravity of sample was slightly higher than KP IV standard. Total ash lied between 0.01 and 0.15% of honey weight which was less than KP IV standard, except 0.56% of Castanea Honey. Studies on mineral compositions (AAS) for honeys and pollen loads showed that $Na^+,\;K^+,\;Ca^{2+},\;Fe^{2+}\;Cu^{2+}\;and\;CO^{2+}$ were the most commonly occuring minerals. Pollen loads showed higher levels of mineral contents than honeys. Castanea Honey revealed rich in minerals. $Cd^{2+}\;and\;Pb^{2+}$ were found relatively higher level in Robinia Honey. Reducing sugar level showed $60{\sim}70$ in honeys and $25{\sim}30$ in pollen loads. Non reducing sugar varied between 2 to 7% in pollen loads.