• 한국분무공학회지
• /
• 제2권4호
• /
• pp.47-53
• /
• 1997

By using a premixed laminar burner, the effect of mixture component on laminar burning velocity($S_L$) was investigated. The following was made clear ; (1)As the humidity$(H_2O)$, $CO_2$ and Ar in mixture is increased, $S_L$ decreased in proportion to quantity of those dilution gases. (2) The heat reaction theory says that mean thermal conductivity $(\lambda_m)$, specific heat $(C_{pm})$ of mixture and adiabatic flame temperatures $(T_b)$ affect $S_L$. As a result of theoretical analysis, the effect of $\lambda_m\;and\;C_{pm}$ on $S_L$ is less than 1/25 of the effect of $T_b$, so the effect of $\lambda_m\;and\;C_{pm}$ can be ignored. (3) From experimental results, it was confirmed that $\ln(S_L)$ is proportional to $(1/T_b)$, that is, the effect of $H_2O$ on $S_L$ is mainly caused by changes of $T_b$. This conclusion was verified by the fact increases of $H_2O,\;CO_2$ and Ar decrease the intensity of radiation typical $C_2$, CH, and OH in the same manner.

• 한국정밀공학회지
• /
• 제23권8호
• /
• pp.47-53
• /
• 2006

The purpose of this study was to investigate the significant characteristics in spray of industrial etch-nozzle for the design of process. The experiment was carried out with different spray pressure and industrial nozzle in wet etch. The characteristics of liquid spray, such as axial velocity and sauter mean diameter measurements were obtained by PDA. And impact force was calculated from spray characteristics. It was found that the fluid with higher spray pressure resulted in the smaller SMD and the higher droplet velocity and impact force. The depth of etch was increased in case of high spray pressure. In the case of injection angle oscillated between $20^{\circ}$, the result indicated constant effect of etch. The correlation between the spray characteristics and etch ones were analyzed. The depth of etch had good positive correlation with axial velocity and impact force. The result clearly shows that the characteristics in wet etch are strongly related to the spray characteristics with process.

• Korean Chemical Engineering Research
• /
• 제49권1호
• /
• pp.83-88
• /
• 2011

점성슬러리 기포탑에서 작은 기포의 체류량 특성에 대해 고찰하였다. 정압 강하방법(Static pressure drop method)에 의해 구한 기포탑 내부전체 기포체류량과 이중저항탐침법(dual resistivity probe method)에 의해 구한 큰 기포의 체류량으로부터 기포탑 내부에 체류하는 작은 기포의 체류량을 구할 수 있었다. 기체유속, 연속액상의 점도 그리고 슬러리 상중에 포함된 고체입자의 분율이 전체 기체체류량, 큰 기포의 체류량 그리고 작은 기포의 체류량에 미치는 영향을 검토하였다. 점성슬러리 기포탑에서 작은 기포의 체류량은 기체의 유속이 증가하면 증가하였으나 연속액상의 점도와 슬러리상에 포함된 고체입자의 분율이 증가하면 감소하였다. 기포탑 내부에 체류하는 전체 기포 체류량 중 작은 기포 체류량의 분율은 기체유속이 증가하면 증가하였으나 연속액상의 점도와 슬러리상에 포함된 고체입자의 분율이 증가하면 감소하였다. 기포탑 내부에 체류하는 작은 기포는 큰 기포의 상승속도에 영향을 미치지 못하였다.

• 한국분무공학회지
• /
• 제13권3호
• /
• pp.134-142
• /
• 2008

In the case of heavy duty diesel engines, the Urea-SCR system is currently considered to reduce the NOx emission as a proved technology, and it is widely studied to get the high performance and durability. However, the nozzles to inject the urea-water solution into the exhaust pipe occur some problems, including the nozzle clogging, deposition of urea-water solution on the inner wall of the exhaust pipe, resulting in the production of urea salt. In this study, a swirl-type twin-fluid nozzle to produce more fine droplets was used as a method to solve the problems. The effect of the nozzle cap geometry, including the length to diameter ratio ($l_o/d_o$) and chamfer, on the spray characteristics were investigated experimentally. The length to diameter ratio of nozzle cap were varied from 0.25 to 1.125. The chamfer angle of the nozzle cap was constant at 90o. The mean velocity and droplet size distributions of the spray were measured using a 2-D PDA (phase Doppler analyzer) system, and the spray half-width, AMD (arithmetic mean diameter) and SMD (Sauter mean diameter) were analyzed. At result, The larger length to diameter ratio of nozzle cap were more small SMD and AMD. The effect of the chamfer did increase the radial velocity, while it did not affect the atomization effect.

• 한국분무공학회지
• /
• 제1권3호
• /
• pp.51-59
• /
• 1996

An experiment was carried out on the structure of twin spray from pressurize-swirl nozzles, in order to investigate the effect of different size of spray nozzles on the characteristics of the overlap of two single sprays, for example, mean diameter, number density, and spatial distribution of flow rate. Using image processing method, the distributions of size and velocity of droplets of a single spray and twin spray were measured and compared to investigate the overlapping effect of two identical sprays. Comparing experimental results from a twin-spray with those from two-single sprays shows that the flow rate distribution of the twin-spray was concentrated around the midst of the overlapping region of two sprays. In this region, Sauter mean diameter (SMD) did not change much in the twin spray from 6032 nozzles, but it was smaller by 10 micrometers in the twin-spray than two-single sprays from 60063 nozzles. In spite of large difference in Weber numbers of the colliding sprays between the 60063 and 6032 nozzles, the phenomena did not have a big change in the overlapping region of twin spray. This shows that in the collision between droplets from two single spray in the overlapping region to cause the disruption of droplets, the size distribution of spray droplets was also important as well as Weber number.

• 대한기계학회논문집B
• /
• 제27권11호
• /
• pp.1618-1629
• /
• 2003

The effects of the interaction between flow field and heat transfer caused by the longitudinal vortices are experimentally investigated using a five hole probe and a transient liquid crystal technique. The test facility consists of a wind tunnel with vortex generators protruding from a bottom surface and a mesh heater. In order to control the strength of the longitudinal vortices, the angle of attack of vortex generators used in the present experiment is 20$^{\circ}$, and the spacing between the vortex generators is 25mm. The height and cord length of the vortex generator is 20mm and 50mm, respectively. Three-component mean velocity measurements are made using a f-hole probe system, and the surface temperature distribution is measured by the hue capturing method using a transient liquid crystal technique. The transient liquid crystal technique in measuring heat transfer has become one of the most effective ways in determining the full surface distributions of heat transfer coefficients. The key point of this technique is to convert the inlet flow temperature into an exponential temperature profile using the mesh heater set up in the wind tunnel. The conclusions obtained in the present experiment are as follows: The two maximum heat transfer values exist over the whole domain, and as the longitudinal vortices move to the farther downstream region, these peak values show the decreasing trends. These trends are also observed in the experimental results of other researchers to have used the uniform heat flux method.

• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2009년도 춘계학술대회 논문집
• /
• pp.267-274
• /
• 2009

아음속 영역의 대류에 평행하게 압력형 스월 제트를 분사시켜 액막 분열 및 액적 크기와 분포를 실험적으로 측정하였다. 대류로 인한 거시적과 미시적인 분무 특성의 영향을 제트 $We_{\iota}$수와 기상에 대한 액상의 운동량 비를 사용하여 광학적인 방법으로 측정하였다. 낮은 제트 $We_{\iota}$수일 때는 제트의 원심력 부족으로 인해 액막을 형성하지 못하고 Rayleigh 제트 분열을 하게 된다. 높은 $We_{\iota}$수에서는 거시적인 분무 특성은 대류의 영향을 거의 받지 않지만 미시적인 분무 특성은 운동량 비가 높을수록 2차 미립화 과정을 통해 대류의 영향을 많이 받았다. 대류는 제트의 분열을 촉진시키고 스월 제트의 분무 특성을 향상하는 것으로 관찰되었다.

• 한국추진공학회지
• /
• 제8권2호
• /
• pp.39-45
• /
• 2004

선회형 미립화기의 분무거동에 관한 논의는 현재 여러 연구자들에 의해 활발히 논의되고 있다. 본 연구에서는 이류체 내부혼합형 선회노즐의 특성을 파악하고자 공기와 액체의 질량 비를 바꿔가며 최적의 미립화 조건을 알아보기 위하여 실시되었다. 이를 위하여 분무 유동장의 평균속도, 파동속도 및 액적크기에 관한 비교를 정량적으로 분석하였다. 각 유동조건에 따른 지수함수를 만족하는 상관관계 또한 도출하였는데, 이는 질량 비에 관계없이 거의 동일함을 알 수 있었고, 질량비가 높을수록 선회 각이 30o인 경우가 미립화 특성이 가장 우수하였다. 따라서, 본 연구에서 이루어진 결과에서는 노즐의 형상이 분무유동에 미치는 여러 인자 중 가장 중요한 것이라 여겨진다.

• 설비공학논문집
• /
• 제12권9호
• /
• pp.843-852
• /
• 2000

The flow characteristics and the heat transfer rate on a surface by interaction of a pair of vortices were studied experimentally. The test facility consisted of a boundary-layer wind tunnel with a vortex introduced into the flow by half-delta winglet protruding from the surface. In order to control the strength of the longitudinal vortices, the angles of attack of the vortex generators were varied from $\pm20\;degree\;to\;\pm45$ degree, but spacings between the vortex generators were fixed to 4 cm. The 3-dimensional mean velocity measurements were made using a five-hole pressure probe. Heat transfer measurements were made using the thermochromatic liquid to provide the local distribution of the heat transfer coefficient. By using the method mentioned above, the following conclusions were obtained from the present experiment. The boundary layer was thinned in the regions where the secondary flow was directed toward the wall and thickened where it was directed away from the wall. The peak augmentation of the local heat transfer coefficient occurred in the downwash region near the point of minimum boundary-layer thickness.

• 대한기계학회논문집B
• /
• 제25권12호
• /
• pp.1869-1878
• /
• 2001

Experiments are carried out to investigate the effect of pulsations on the flow and heat transfer characteristics of an axisymmetric impinging jet on a flat plate heated by using a gold coated aim. Vertex motion in the impinging jet is visualized using a fog generator, and a thermochromatic liquid crystal (TLC) technique is used to measure the time averaged local temperature distributions on the impingement plate. In addition, the quantitative data for mean velocity and turbulence intensity are obtained employing hot-wire anemometer. Parameters such as pulsating frequency (f = 0, 10 and 20 Hz) and the nozzle-to-palate spacing (H/D = 2, 10) are considered at the jet Reynolds number of 20,000. Consequently, the significant changes of flow structure and local Nusselt number distribution due to pulsations are observed. In the case of H/D = 2, the enhanced heat transfer coefficient exceeding 30 % is observed at the stagnation point. At the high H/D, heat transfer rate increases with pulsation frequency.