• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2004.11a
• /
• pp.116-119
• /
• 2004

In this paper, we have improved a novel (ECB) mode using tilt angle in the unique condition by hot-plate equipment. The new control of tilt angle for nematic liquid crystal (NLC) with negative and positive dielectric anisotropy on the rubbed homeotropic polyimide (PI) using baking method by Hot-plate equipment was investigated. LC tilt angle decreased with increasing baking temperature and time. Especially, the low LC tilt angle of positive type NLC $({\Delta}n>0)$ on the rubbed homeotropic PI surface by increasing temperature and time was measured. The EO characteristics of the novel ECB mode using control of tilt angle on the homeotropic surface than that of conventional OCB cell can be improved. We suggest that the developed the Novel ECB cell using control of tilt angle on the homeotropic surface is a promising technique for the achievement of a fast response time and a high contrast ratio.

• Bulletin of the Korean Chemical Society
• /
• v.33 no.7
• /
• pp.2224-2228
• /
• 2012

This study describes the ability of capillary electrochromatography (CEC) for the determination of imidacloprid and carbendazim in tomato samples. A novel liquid crystal crown ether modified hybrid silica monolithic column was synthesized, characterized and developed as separation column for the first time. Baseline separation of imidacloprid and carbendazim could be achieved using a mobile phase containing 90% (v/v) 20 mmol/L phosphate buffer (pH 7.0) and 10% (v/v) acetonitrile. The matrix matched calibration curves were linear with correlation coefficient $r^2$ > 0.9998 in the range of 0.20-10.00 mg/L. The limits of detection for imidacloprid and carbendazim were 0.061 and 0.15 mg/kg, respectively, which were below the maximum residue limits established by the European Union as well as Codex Alimentarius. Average recoveries for imidacloprid and carbendazim varied from 101.6-108.0% with relative standard deviations lower than 6.3%. This method was applied to the analysis of tomatoes collected from local markets.

• Polymer(Korea)
• /
• v.34 no.4
• /
• pp.369-375
• /
• 2010

We used melt polymerization method to prepare a series of aromatic liquid crystals (LCs) based on aromatic ester and amide units with the reactive methyl-maleimide end group, and then the resulting thermally cross-linked LCs to produce LC thermoset films by means of solution casting and the followed heat treatment. The synthesized LCs and LCTs were characterized by Fourier transform infrared (FTIR) spectroscopy, differential scanning calorimetry (DSC), thermogravimetric analysis (TGA), thermomechanical analysis (TMA), X-ray diffractometry (XRD), and polarizing optical microscopy (POM) with a hot stage. All of the LCs prepared by melt polymerization method formed smectic mesophases. The thermal properties of the LC and LCT films were strongly affected by the mesogen units in the main chain structures. The thermal expansion coefficients of samples were in the range of 27.72~50.95 ppm/$^{\circ}C$.

• Journal of the Korean Applied Science and Technology
• /
• v.33 no.1
• /
• pp.1-12
• /
• 2016

This study is to make the liquid crystalline structure using sucrose distearate (Sucro-DS) emulsifier to create the hydrophilic type oil-in-water (O/W) emulsion, the droplets of the emulsion having a structure of a multi-lamellar structure. We have studied the physicochemical properties of Sucro-DS using those techniques. And it has been studied in the emulsion performance. In order to form the liquid crystalline structure applying 3 wt% of Sucro-DS, 5 wt% of glycerin, 5 wt% of squalane, 5 wt% of capric/caprylic triglyceride, 3wt% of cetostearyl alcohol, 1wt% of glyceryl mono-stearate, 78 wt% of pure water in mixture having the lamellar structure of stable multi-layer system was found to formed. By applying them, they were described how to create an unstable active material encapsulated cream. Further, the moisturizing cream was studied using this technique. It reported the results to the skin improvement effect by the human clinical trials. The pH range to produce a stable liquid crystal phase using a Sucro-DS was maintained in 5.2~7.5. In order to increase the stability of the liquid crystal, it was when behenyl alcohol containing 3 wt%, the hardness at this time was 13 kg/mm,min. Viscosity of the same amount was 25,000mPas/min. After a test for the effects of the emulsions, the concentration of 6 wt% Sucro-DS is that was appropriate, the particle size of the liquid crystal was 4~6mm. It was observed through a microscope analysis, reliability of the liquid crystal changes for 3 months was found to get stable at each $4^{\circ}C$, $25^{\circ}C$ and $45^{\circ}C$. In clinical trial test, before applying a moisturizing effect it was $13.4{\pm}7%$. Moisturizing cream liquid crystal was not formed in $14.5{\pm}5%$. Therefore, applying than ever before could see the moisture about 8.2% was improved. On the other hand, it was the moisturizing effect of the liquid cream is $19.2{\pm}7%$. The results showed that 43.3% improvement than that previously used. Applications fields, Sucro-DS emulsifier used liquid cream, lotion, eye cream and a variety of formulations can be developed, as well as the cosmetics industry is expected to be wide fields in the application of the external preparation for skin emulsion technology in the pharmaceutical industry and pharmaceutical industry.

• Design & Manufacturing
• /
• v.2 no.2
• /
• pp.29-32
• /
• 2008

A back light unit (BLU) is a key module of a thin film transistor liquid crystal display (TFT-LCD), frequently utilized in various mobile displays. In this study, we experimentally characterize transcription and optical properties of concave and convex microlens arrays (MLAs) of light guide plate (LGP) fabricated by injection molding with polycarbonate as a LGP substrate material. Nickel mold inserts were manufactured by electroforming on the MLA which was fabricated by the thermal reflow of photoresist microstructures patterned by UV-photolithography. For the case of convex microlens, the height of replicated microlens was less than that of the mold insert while maintaining almost the same microlens diameter of the mold insert as the location of the microlens is far from the gate. In contrast, for the concave microlens, the diameter of replicated microlens was larger than that of mold insert, while showing almost the same microlens height as the mold insert. From the optical examination of replicated convex and concave MLAs, it was found that a higher luminance of the LGP was achieved by the concave MLAs compared to the convex MLAs (about 30% enhancement in this case)due to the utilization of a larger amount of light provided by the light sources.

• Bulletin of the Korean Chemical Society
• /
• v.25 no.8
• /
• pp.1171-1176
• /
• 2004

Three banana-shaped achiral compounds, 4-chloro-1,3-phenylene bis [4-{4-(undecenyloxy)phenyl imino-methyl} benzoate] derivatives, were synthesized with variation of a substituent (x=H, F, Cl); their antiferro-electric properties are described. The smectic mesophases, including a switchable chiral smectic C(Sm $C^{\ast}$) phase, were characterized by differential scanning calorimetry, polarizing optical microscopy, triangular wave method, and X-ray diffractometry. The presence of vinyl groups at the terminals of linear side wings in the banana-shaped achiral molecules induced a decrease in melting temperature and formation of the switchable Sm $C^{\ast}$ phase in the melt. The smectic phase having a lateral fluorine-substituent at 3-position of the Schiff's base moiety showed antiferroelctric switching, and the value of spontaneous polarization on reversal of an applied electric field was 250 nC/$cm^2$ .

• 한국정보디스플레이학회:학술대회논문집
• /
• 2009.10a
• /
• pp.1112-1114
• /
• 2009

In this paper, we have studied manufacturing process for liquid crystal displays (LCDs) using plastic substrates. Because the thermal and dimensional stabilities of plastic substrates are decisive issues, both the process and materials were improved to fit the manufacturing requirements of flexible twisted-nematic (TN) and color super-twisted nematic (CSTN) LCDs. Finally, to broaden the flexible display applications, we take advantage of the unique properties of flexible display to design several innovative products.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.18 no.10
• /
• pp.69-74
• /
• 2017

In this study, cholesteryl 4-n-alkoxybenzoates (Chol-n), with alkyl groups used for controlling the temperature of transition to the liquid crystal phase, were synthesized, and the effects of the length of the alkyl groups on the physical properties of the liquid crystal compounds were investigated. The chemical structures and thermal and liquid crystalline properties of the synthesized compounds were investigated by Fourier transform infrared spectroscopy (FT-IR), proton nuclear magnetic resonance spectroscopy ($^1H$-NMR), differential scanning calorimetry (DSC), and polarizing optical microscopy (POM). The synthesized compounds showed melting transition temperatures ($T_m$) in the range of $103^{\circ}C$ to $143^{\circ}C$ and all of the compounds except Chol-6 exhibited a wide liquid crystal phase temperature range of about $60^{\circ}C$ to $100^{\circ}C$. No correlation between the number of carbon atoms in the molecule and the thermal properties of the compounds was found. All of the synthesized compounds showed an enantiotropic cholesteric phase, which was accompanied by a chiral smectic phase in the compounds Chol-6, Chol-8, Chol-9, and Chol-10. All of the compounds exhibited thermochromism in the liquid crystal state, and their color changed from red to blue as the temperature was increased.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2006.08a
• /
• pp.1473-1475
• /
• 2006

The electro-optic properties of an active-matrix polymer network liquid crystal display (AM-PNLCD) with crossed polarizer films to improve its contrast ratio were evaluated. By using crossed polarizer films, it shows good contrast ratio as well as wide viewing angle and adequate response time at normal TFT-twisted nematic (TN) LCD driving voltage (2.8V).

• Fibers and Polymers
• /
• v.2 no.1
• /
• pp.123-130
• /
• 2001

Photoresponsive side chain copolymer and homopolymer containing an aminonitroazobenzene were synthesized for studying photoisomerization behavior and photo-induced anisotropy. Trans-to-cis photoisomerization was observed under the exposure of a circularly polarized visible light with UV-Vis absorption spectroscopy. Reorientation of polar azobenzene molecules induced optical anisotropy under a linearly polarized light at 532nm. Polarized absorption spectroscopy was employed to investigate the anisotropy of the polymer film during irradiationg of the excitation light. Layers of two photosensitive polymers were used for aligning liquid crystal(LC) molecules instead of one of the rubbed polyimide layers in the conventional twisted nematic cell. For producing homogeneous alignment of a nematic LC molecule, a linearly polarized light was exposed to the films of two polymers. The stability of the LC alignment upon the linearly polarized light exposure was also studied.