• KSII Transactions on Internet and Information Systems (TIIS)
• /
• 제11권11호
• /
• pp.5200-5222
• /
• 2017

The separation of control plane and data plane in Software Defined Network (SDN) makes it flexible to control the network behavior, while also causes some inconveniences to the link failure recovery due to the delay between fail point and the controller. To avoid delay and packet loss, pre-defined backup paths are used to reroute the disrupted flows when failure occurs. However, it may introduce large overhead to build and maintain these backup paths and is hard to dynamically construct backup paths according to the network status so as to avoid congestion during rerouting process. In order to realize congestion aware fast link failure recovery, this paper proposes a novel method which installs multi backup paths for every link via source routing and per-hop-tags and spread flows into different paths at fail point to avoid congestion. We carry out experiments and simulations to evaluate the performance of the method and the results demonstrate that our method can achieve congestion aware fast link failure recovery in SDN with a very low overhead.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• 제29권7A호
• /
• pp.844-851
• /
• 2004

Various types of error are caused due to many factors of various environment in air interface channel of wireless communications. In this case, the reliability of the channel is much lower than that of wired case. IEEE 802.15.3 high-rate WPAN, which operates in an ad hoc networking environment, is more susceptible to such errors. The problem has been investigated for wireless LANs, for example, as follows. If the queue size of a certain node is longer than that of other nodes, the node estimates that its channel state is bad and the resource of the node is decreased. However this method has a disadvantage that a central controller must always monitor the status. To avoid this disadvantage, in this paper, a new MAC protocol that the throughput of overall piconet is increased by LDS (Link-status Dependent Scheduling) is proposed.

• Proceedings of the Korean Information Science Society Conference
• /
• 한국정보과학회 2008년도 한국컴퓨터종합학술대회논문집 Vol.35 No.1 (D)
• /
• pp.440-443
• /
• 2008

WCDMA 시스템에서 radio link간에 data를 주고 받고 신뢰성 있는 data를 검증하는 layer가 RLC이다. RLC에서는 전송 측에서 전송한 data가 수신 측에 잘 전송이 되었는지 status report를 확인을 받고 전송이 이루어지지 않았을 경우 재전송을 한다. 재전송 메커니즘에는 poll 및 status 관련 timer가 존재하면 이러한 파라미터값을 적절히 사용하지 않으면 불필요한 data의 재전송으로 인한 radio resource 낭비 및 시스템 throughput에 영향을 준다.

• Proceedings of the IEEK Conference
• /
• 대한전자공학회 2003년도 하계종합학술대회 논문집 I
• /
• pp.210-213
• /
• 2003

This paper presents a beamforming algorithm for the uplink application of a linear array antenna for WCDMA system. A steering beamforming algorithm is designed using a block DFT algorithm and its performance is analyzed and verified using computer simulations. Various environmental parameters such as the number of antenna elements, the number of users, the mobility of the target user, and the status of fast power control are reflected in the simulation study providing themselves as useful design and implementation guides for the reverse link beamforming of WCDMA system.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 한국정보통신학회 2012년도 춘계학술대회
• /
• pp.85-87
• /
• 2012

This paper, UAVs of the secondary communication link that applies to the analysys of time-division communication system and communication method proposed algorithm has been developed. UAVs of the important characteristics of the data link latency and throughput, the frequency is availability, weight. The data needed to operate UAVs vehicle control data, status data, there is an acquisition. Control and data acquisition will require real-time communication. Based on the requirements being applied to the secondary communication link communication method were compared and analyzed. The results of analysis of ground-base TDD method is suitable.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• 제19권7호
• /
• pp.24-35
• /
• 2018

In wireless communications environments, a link adaptation technique that selects the proper rate from among several transmission rates is adopted to cope with variations in channel status. In block coded modulation, the frame time and/or the block length can be adjusted to the channel status. A smaller frame time can cause inter-frame interference (IFI), however, a larger frame time can reduce the data rate. Therefore, frame time is the design factor decided by a tradeoff between performance and the data rate. This paper presents a method to determine the frame time based on the processing gain for the channel model, CM1~CM4, recommended by IEEE 802.15a. Also, a link adaptation technique for block coded modulation is proposed for efficient communications by varying the frame time and the block length. Through simulation, link adaptation can be carried out with a step size of 2~5 nsec in a frame time range of 14~ 50 nsec for channel models CM1~CM4.

• Journal of the Korean Society for Aviation and Aeronautics
• /
• 제25권3호
• /
• pp.51-60
• /
• 2017

Estimation of the taxi-out and taxi-in times of aircraft on a airport surface is one of the essential features of Departure Manager (DMAN). Especially for an airport with multiple runways and large ramp areas, estimation of the taxi-out and taxi-in times are mainly dependent on the taxi routes on airport surface. This paper described the method of automatic extraction of the the taxi routes using the ASDE track data and the Dijkstra algorithm based on the node-link model of a airport surface movements. In addition, we analyzed the ground operation status of Incheon International Airport using the extracted taxi routes.

• The Transactions of the Korean Institute of Electrical Engineers P
• /
• 제60권2호
• /
• pp.94-98
• /
• 2011

Electrolytic power capacitors today form essential components for virtually any power electronic system such as DC/DC converter or UPS. Frequently, electrolytic capacitors for DC link voltage smoothing are the key components which determine the life cycle of the whole unit and often are responsible for converter breakdown failures. In this paper, ethernet-based remote diagnosis system for DC voltage smoothing capacitor using DSP control board is developed. To estimate the status of the capacitor, the equivalent series resistor(ESR) of the component has to be determined. The ESR detection scheme is based on the determination of the capacitor ripple power losses calculated from DC link voltage/current measurement. Experimental results show the veridity and reliability of the proposed ethernet-based remote on-line capacitor diagnosis system.

• The Transactions of the Korean Institute of Electrical Engineers B
• /
• 제52권12호
• /
• pp.649-654
• /
• 2003

The simplest method for measuring output currents of the three phase inverters is to measure them with three current sensors such as hall sensors. This method requires at least two current sensors, and these types of sensors are somewhat expensive. More economical method is measuring DC link current with a simple shunt resistor, then, reconstructing output current using the DC link current value and the switching status. However, in low speed region, the measurement becomes difficult and even impossible due to the requirement of minimum switching duration for A/D conversion. These problems can be overcome by limitation of switching duration. Limitation of switching, however, causes voltage and current distortion. Owing to compensation, distortion can be effectively suppressed. However these increase acoustic noise due to increment of current ripple. In this paper, a current measurement method is proposed, which can reduce minimum switching duration resulting in reduction of acoustic noise. The validity of proposed method is confirmed through experiment.

• The Transactions of the Korean Institute of Power Electronics
• /
• 제12권5호
• /
• pp.372-377
• /
• 2007

This paper proposes a novel fault diagnosis method of a electrolytic capacitor used for DC-link voltage smoothing in adjustable speed drives. The equivalent series resistance (ESR) of the electrolytic capacitor is directly estimated from DC-link voltage and load currents and the status of the electrolytic capacitor is determined from the estimated ESR. To compensate the variation of the ESR owing to temperature variation, diodes are located on the same PCB near the capacitor and the temperature of the capacitor is sensed indirectly from the voltage drop of diodes. Simulation and experimental studies show the effectiveness of the proposed method.