• Journal of Electrical Engineering and Technology
• /
• v.10 no.2
• /
• pp.529-538
• /
• 2015

Due to the high efficiency and compact mechanical structure, direct drive variable speed generators are used for power conversion in wind turbines. The wind energy conversion system (WECS) considered in this paper consists of a permanent magnet synchronous generator (PMSG), uncontrolled rectifier, dc-dc boost converter controlled with maximum power point tracking (MPPT) and adaptive hysteresis controlled voltage source inverter (VSI). For high utilization of the converter's power capability and stabilizing voltage and power flow, constant DC-link voltage is essential. Step and search MPPT algorithm which senses the rectified voltage ($V_{DC}$) alone and controls the same is used to effectively maximize the output power. The adaptive hysteresis band current control is characterized by fast dynamic response and constant switching frequency. With MPPT and adaptive hysteresis band current control in VSI, the DC link voltage is maintained constant under variable wind speeds and transient grid currents respectively.

• The Transactions of the Korean Institute of Electrical Engineers
• /
• v.43 no.6
• /
• pp.936-945
• /
• 1994

This paper proposes a new power converter which consists of two identical 3-phase PWM modulators and a novel resonant circuit. A new control strategy is integrated to realize the bidirectional power converter without an electrolytic link capacitor. The power flow between converters is bidirectional and the regenerative braking is inherent. The source side currents maintain sinusoidal waveforms with a unity power factor. It is observed in the experiment that by balancing the active power between the source and load side, the voltage across a small ceramic link capacitor can be maintained within a small deviation from the reference. Simulation results and experimental results are presented to verify the operational principles.

• Journal of the Korean Society of Industry Convergence
• /
• v.6 no.4
• /
• pp.339-345
• /
• 2003

The purpose of this thesis is to develop a simulation model to estimate link travel speed applicable to urban street transportation planning for interrupted traffic flow, influenced by signalized intersection. This link travel speed model is expected to be a better and more than previous studies.

• Proceedings of the IEEK Conference
• /
• 2001.06a
• /
• pp.25-28
• /
• 2001

In this paper we implement moving picture transfer system using bluetooth Development Kit (DK). To reduce the size of the image data, we use M-JPEG compression. We use bluetooth Synchronous Connection-Oriented (SCO) link to transfer voice data. Server receive image data from camera and compress the image data in M-JPEG format, and then transmit the image data to client using bluetooth Asynchronous connection-less (ACL) link. Client receive image data from bluetooth ACL link and decode the compressed image and then display the image to screen. Sever and Client can transmit and receive voice data simultaneously using bluetooth SCO link. In this paper bluetooth HCI commands and events generated by host controller to return the results of HCI commands are explained and the flow of bluetooth connection procedure is presented.

• Journal of Power Electronics
• /
• v.12 no.4
• /
• pp.664-676
• /
• 2012

A phase shift algorithm based on the closed-loop control of dc-link voltage implemented on a series active voltage quality regulator (AVQR) is proposed in this paper. To avoid pumping-up the dc-link voltage, a general phase shift compensation strategy is applied. The relationships among the operation variables are discussed in detail, which is very important for guiding the design of both the main circuit and the control system. Then on the basis of an investigation of the dc-link voltage pumping-up from viewpoint of the active power flow, a novel phase shift control method based on the closed-loop of the dc-link voltage is proposed. This method can adjust the phase of the output voltage gradually and automatically according to the dc-link voltage variation without introducing a phase jump. The effectiveness of the proposed strategy is verified through simulations of a single-phase 5kVA prototype and laboratory experiments on both a single-phase 5kVA and a three-phase 15kVA prototype.

• Proceedings of the KIPE Conference
• /
• 2003.07b
• /
• pp.560-564
• /
• 2003

This paper proposes a simple control strategy based on the discontinuous PWM(DPWM) to balance the DC-link voltage of three-level Neutral-Point-Clamped(WPC) inverters at low modulation index. New DPWM methods in multi-level inverter are also introduced. The proposed DPWM method changes the path and duration to flow the neutral point current out of or into neutral point of the DC-link and it makes the overall fluctuation of the DC-link voltage zero during a sampling time of reference voltage vector. Therefore, the voltage of the DC-link can be balanced fairly well and also the voltage ripple of the DC-link is reduced significantly. Moreover, comparing with conventional methods, the proposed strategy is very simple. The validity of the proposed DPWM method is verified by experiment

• The Transactions of the Korea Information Processing Society
• /
• v.4 no.11
• /
• pp.2822-2831
• /
• 1997

A B-ISDN network based on ATM must support several kinds of transport services with different traffic characteristics and service requirements. There is neither link-by-link flow control nor error control in the ATM layer. For different services, different flow/error controls could be performed at the AAL layer or at a higher Iayer(e.g. transport layer). In traditional data networks, the window now control mechanism combined with error control was used prevalently. But, the window flow control mechanism might be useless in ATM networks because the propagation delay is too large compared with the transmission rate. In this paper, we propose a simple flow control mechanism, called RCT(Rate Control for end-to-end Transport), for end-to-end data transport. The RCT shows acceptable performance when the average overload period is bounded by a certain time.

• The Journal of the Korea Contents Association
• /
• v.9 no.3
• /
• pp.49-57
• /
• 2009

This paper has proposed Flow Holding Time based Link State Update(LSU) Algorithm that can improve the performance of the existing LSU algorithms. As the existing LSU algorithms are based on the network traffic information, the proposed algorithm is based on flow holding time so we can minimize the LSU message overhead and has not had a strong influence on the depreciation of QoS routing performance. We apply a flow holding time in order to decrease the number of LSU message. We have evaluated the performance of the proposed model and the existing algorithms on MCI simulation network using the performance metric as the QoS routing blocking rate and the mean update rate per link, it thus appears that we have verified the performance of this algorithm.

• Journal of Communications and Networks
• /
• v.9 no.4
• /
• pp.419-427
• /
• 2007

In wavelength-division-multiplexing(WDM) networks a link failure may cause the failure of several high-bit-rate optical channels, thereby leading to large data loss. Recently, various protection and restoration mechanisms have been proposed to efficiently deal with this problem in mesh networks. Among them, dedicated path protection(DPP) is a promising candidate because of its ultra-fast restoration time and robustness. In this work we investigate the issue of planning and optimization of WDM networks with DPP. Integer linear programming(ILP), in particular, is one of the most common exact method to solve the design optimization problem for protected WDM networks. Traditional ILP formalizations to solve this problem rely on the classical flow or route formulation approaches, but both these approaches suffer from a excessively high computational burden. In this paper, we present a variable-aggregation method that has the ability of significantly reducing the complexity of the traditional flow formulation. We compare also the computational burden of flow formulation with variable aggregation both with the classical flow and route formulations. The comparison is carried out by applying the three alternative methods to the optimization of two case-study networks.

• Journal of the Korean Society of Industry Convergence
• /
• v.19 no.4
• /
• pp.216-222
• /
• 2016

Thus, this study aimed to develop a gear-type vane damper in order to replace the link-type vane damper. To achieve this goal, the torque generated in a gear-type vane damper was analyzed, and a structural analysis was conducted. In addition, the fluid flow was analyzed according to the changes in the vane's angle, and experimental tests such as a dry-heat test and cold test were conducted considering the operating conditions of the vessels. Moreover, an appropriate actuator was selected for the developed gear-type vane damper, and studies on the reduction in the backlash due to the facing-pressure adjustment length and flow rate and leakage test due to the vane's angle were conducted.