• 한국자기학회지
• /
• 제14권1호
• /
• pp.52-57
• /
• 2004

본 연구에서는 ㎓ 대역의 박막 인덕터 특성을 수치해석 하였다. 인덕터의 기본 구조는 390$\mu\textrm{m}$${\times}$390$\mu\textrm{m}$, 5.5턴(turn), 선폭 10$\mu\textrm{m}$와 선간격 10$\mu\textrm{m}$의 사각 나선형이다. 주파수 특성은 10 ㎓까지 시뮬레이션 하였다. 기판은 Si, Sapphire, 유리와 GaAs를 모델로 하였고 도체는 Cu이다. 도체의 두께는 2$\mu\textrm{m}$로 고정하였다. 입력과 출력단자의 위치가 서로 반대가 되도록 하기 위하여 턴수는 n.5로 하였다. 기본 구조 인덕터는 초기 인덕턴스 13.0 nH,최대 인덕턴스 60.0 nH 그리고 공진주파수는 4.25 ㎓이었다. 기판의 유전상수가 증가하면 초기 인덕스는 거의 변화가 없으나 공진 주파수는 감소하였다. 인덕터의 턴수를 1.5에서 9.5로 변화시키면, 초기 인덕턴스는 2.9 nH며 16.9 nH로 포화되었으며 Q factor는 소폭 증가하였다. 인덕터의 선폭과 선간격을 증가시키면 초기와 최대 인덕턴스는 감소하였다. 공진 주파수는 증가하였으며, Q factor는 선폭과 선간격을 증가시키면 각각 증가와 감소를 나타내었다.

• 한국결정성장학회지
• /
• 제27권2호
• /
• pp.75-79
• /
• 2017

고밀도 플라즈마 식각 및 lift-off 두 가지 공정으로 honeycomb 형상의 Ag-grid 투명전극층을 제작하였고 제조 공법에 따른 광학적 및 전기적 특성을 비교하였다. 플라즈마 식각 조건 선정을 위하여 Ag 박막의 $10CF_4/5Ar$ 유도결합 플라즈마 식각특성을 조사하였다. 비교적 낮은 ICP source power 또는 rf chuck power 영역에서는 power 증가에 따라 Ag 식각속도가 증가하였고, 높은 power 조건에서는 $Ar^+$ 이온 에너지 감소 또는 $Ar^+$ 이온에 의한 F radical 제거로 인해 식각속도가 감소하였다. $10CF_4/5Ar$ 플라즈마 식각 공정에 의해 제작된 Ag-grid 전극층은 lift-off 공정으로 제작된 전극층에 비해 grid 패턴 형상의 왜곡이나 단절이 없는 더 우수한 grid 패턴 전사 효율과 가시광선 영역에서 더 높은 83.3 %(pixel 크기 $30{\mu}m$/선폭 $5{\mu}m$)와 71 %(pixel 크기 $26{\mu}m$/선폭 $8{\mu}m$)의 광투과율을 각각 나타내었다. 반면에 lift-off 공정으로 제작된 Ag-grid 전극층은 플라즈마 식각 공정 시편보다 더 우수한 $2.163{\Omega}/{\square}$(pixel 크기 $26{\mu}m$/선폭 $8{\mu}m$)과 $4.932{\Omega}/{\square}$(pixel 크기 $30{\mu}m$/선폭 $5{\mu}m$)의 면저항 특성을 나타내었다.

• 한국산학기술학회논문지
• /
• 제19권10호
• /
• pp.346-351
• /
• 2018

금속 3D 프린팅 기술은 레이저 빔의 초점에 금속분말을 주입하는 방식에 따라 대표적으로 PBF(Powder Bed Fusion)방식과 DED(Direct Energy Deposition)방식으로 나뉜다. DED 방식은 금속 분말 도포와 동시에 레이저를 조사하여 3차원 구조물을 제작하는 금속 3D 프린팅 기술이고, PBF 방식은 일정 높이로 3차원 그래픽을 슬라이싱 한 후 한 층씩 금속 분말을 적층하여 레이저를 이용해 3차원 구조물을 제조하는 방식이다. DED 방식을 사용하면 레이저 클래딩, 금속 용접 등에는 강점을 가지지만 3D 형상을 제작할 경우 밀도가 낮아지는 문제점이 발생한다. DED 방식에서의 구조체 밀도 문제를 해결하기 위해 PBF 방식을 도입하면 상대적으로 밀도가 높은 3차원 구조물을 제작하는데 용이하다. 본 논문에서는 갈바노 스캐너와 광섬유로 전송되는 Nd:YAG 레이저 빔을 이용한 약 $30{\mu}m$ 크기의 스테인리스 강 분말을 이용하는 PBF 방식의 3차원 프린터를 제작하고, 이를 이용하여 얇은 금속 구조물을 제작하였다. 또한 레이저의 조사 횟수, 출력, 초점 크기, 스캐닝 속도에 따른 선폭의 최적조건을 찾았으며, 그 결과 최적 조건은 레이저 조사 횟수 2회, 출력 30 W, 초점 크기 $28.7{\mu}m$, 스캐닝 속도 200 mm/s에서 최소 선폭은 약 $85.3{\mu}m$로 측정되었다.

• 대한치과보철학회지
• /
• 제29권1호
• /
• pp.73-89
• /
• 1991

Impression ragistration is an improtant and difficult phase of prosthodontic treatment procedures and a tray of appropriate size and shape is essential to obtain the accurate impression. Particularly, in edentulous patients, the size and forms of their residual alveolar ridges are different from one another. Therefore, in this study, various measurements were taken on the edentulous models. And the measurements were analyzed and compared with one another. The results were as follows ; 1. The mean of denture bearing area was $32.86cm^2$ in the upper jaws, $24.20cm^2$ in the lower jaws and the variation of denture bearing area was greater in the upper than in the lower jaws and in males than in females. 2. The mean of A-P(anteroposterior) ridge length was 48.72mm in the upper jaws, 53.05mm in the lower jaws and that of males was longer than that of females. 3. The mean of most posterior ridge width was 47.23mm in the upper jaws, 58.03mm in the lower jaws and the difference of that between males and females was least in both jaws. 4. In the upper jaws, the mean of ridge width was 29.66mm on anterior 1/4, 42.79mm on middle, 48.95mm on posterior 1/4 line and the mean of palatal height was 4.56mm on anterior 1/4, 10.01mm on middle, 10.84mm on posterior 1/4 line. 5. In the lower jaws, the mean of ridge width was 33.24mm on anterior 1/4, 50.19mm on middle, 59.16mm on posterior 1/4 line and the mean of lingual ridge height was 5.49mm on anterior 1/4, 9.16mm on middle, 16.72mm on posterior 1/4 line. 6. The correlation coefficient(=r) between denture bearing area and A-P ridge length was 0.83 in the upper jaws and 0.75 in the lower jaws. The corelation between denture bearing area and AP ridge length was statistically significant, but, between denture bearing area and A-P ridge length and between A-P ridge length and the most posterior ridge width was not statistically significant in both jaws. 7. Alveolar ridge forms were classified into three(ovoid, "u" shape, and "v"shape) categories. In the upper jaws, ovoid was 66%, "u" shape was 24%, and "v" shape was 10%, in the lower jaws, ovoid was 66.7%, "u" shape was 20%, and "v" shape was 13.3%.

• 대한치과교정학회지
• /
• 제14권2호
• /
• pp.249-261
• /
• 1984

This study was to investigate the fitness of the dental arch line to the parabola, and to estimate correlation between the parabola and some ratios of the dental arch measurements. The sample was consisted of the 64 plaster casts showing normal occlusion which was taken from males and females of Korea, aging from 15 to 18 years. The photos of occlusal surface of the plaster casts were taken, and 38 landmarks on the film were selected. The 3 dental arch lines on each dental arch were imaged. One is the dental arch line passing the points of the most buccal surfaces of the teeth, another is that passing the buccal cusp tips of the posterior teeth and the incisal edges, and the other is that passing the midpoints of the teeth. The landmarks on the film were digitized, and measurements and statistics were performed by the IBM computer. The results were as follows; 1. The fitness of the dental arch to the parabola was very good. The fitness of thor upper dental arch was above $91\%$, and that of the lower dental arch was $93\%$. 2. The dental arch line passing the points of the most buccal surfaces of teeth was best fit to the parabola, the buccal cusp tip arch line and the midpoint arch line in order. 3. Correlation between the ratio of oblique molar dental height to molar width and the parabola was very high. 4. The ratio of oblique molar dental height to molar width was devided into 4 groups by the quartiles, and mean parabolic equations and curves were calculated and drawn.

• 한국자기학회지
• /
• 제21권6호
• /
• pp.208-213
• /
• 2011

Mori-Kawabata의 사영 연산자 방법을 $^{55}Mn$이 첨가된 $SrTiO^3$ 단 결정에 직접 적용하여, 이를 운동 방정식의 형태로 만드는 이론 체계를 사용하여 선모양 함수를 계산하였다. 외부 진동수 ${\nu}_0$ = 9.6 GHz에서 서로 다른 농도 [Mn] = 0.5 wt%와 2 wt%에 대한 온도 의존성으로 선폭을 조사하였다. 온도가 증가함에 따라 선폭은 감소하는 경향으로 확인되었고, 이는 선모양의 운동 좁아짐으로 보이며 고온영역 에서는 실험값과 비교적 일치함을 알 수 있었다. 이와 같이 계를 기술하는 스핀 해밀토니안에 연산자 방법을 이용한 선모양 함수는 실제 계의 적용에 편리한 급수전개로 하였으며, 다른 방법들에 비해 비교적 쉽게 계산할 수 있었다.

• ETRI Journal
• /
• 제37권1호
• /
• pp.128-137
• /
• 2015

In this work, a fishbone-type transmission line employing a comb-type ground plane (FTLCGP) was fabricated on polyethersulfone (PES) substrate, and its RF characteristics were thoroughly investigated. According to the results, it was found that the FTLCGP on PES showed periodic capacitance values much higher than other types of transmission lines due to a coupling capacitance between the signal line and ground, which resulted in a reduction of wavelength and line width. Using the theoretical analysis, we also extracted the bandwidth characteristic of the FTLCGP on PES. According to the result, the FTLCGP structure showed a cut-off frequency of 280 GHz.

• 천문학회지
• /
• 제48권3호
• /
• pp.203-206
• /
• 2015

The masses of supermassive black holes in active galactic nuclei (AGN) can be derived spectroscopically via virial mass estimators based on selected broad optical/ultraviolet emission lines. These estimates commonly use the line width as a proxy for the gas speed and the monochromatic continuum luminosity, λL_λ, as a proxy for the radius of the broad line region. However, if the size of the broad line region scales with the bolometric AGN luminosity rather than λL_λ, mass estimates based on different emission lines will show a systematic discrepancy which is a function of the color of the AGN continuum. This has actually been observed in mass estimates based on Hα/Hβ and C_IV lines, indicating that AGN broad line regions indeed scale with bolometric luminosity. Given that this effect seems to have been overlooked as yet, currently used single-epoch mass estimates are likely to be biased.

• 대한기계학회논문집A
• /
• 제25권11호
• /
• pp.1720-1729
• /
• 2001

Wear characteristics of Nylon and acetal pinions against steel gears for different pitch line velocities was studied with a power circulating gear test rig under unlubricated condition. Specific wear rate was measured as a function of tooth number, module, tooth width and total revolution. The worn tooth surfaces were examined with a profile projector. The Nylon pinion showed lower specific wear rate than the acetal pinion. However, the Nylon pinion was fractured at high tooth loads, whereas the acetal pinion exhibited a steady wear behavior. The wear characteristics of Nylon pinion varied significantly with the Pitch line velocity. Wear occurred most severely at the tooth tip and the region immediately below the pitch line of pinion. The dominant wear mechanisms were adhesion and abrasion.

• Journal of Welding and Joining
• /
• 제19권6호
• /
• pp.600-607
• /
• 2001

A CCD camera with a laser stripe was applied to realize the automatic weld seam tracking in GMAW. It takes relatively long time to process image on-line control using the basic Hough transformation, but it has a tendency of robustness over the noises such as spatter and arc light. For this reason. it was complemented with adaptive Hough transformation to have an on-line processing ability for scanning specific weld points. The adaptive Hough transformation was used to extract laser stripes and to obtain specific weld points. The 3-dimensional information obtained from the vision system made it possible to generate the weld torch path and to obtain the information such as width and depth of weld line. We controled the wire feeding rate using informations of weld line.