• Structural Engineering and Mechanics
• /
• 제8권4호
• /
• pp.421-438
• /
• 1999

In this paper a practical limit load estimating procedure is proposed for general pipe-elbow structures subjected to complex loading (in-plane and out-of-plane bending, internal pressure and axial force). The explicit calculating formulae are presented on the basis of theoretical analysis combined with numerical simulation. Von Mises' yield criterion is adopted in both analytical and numerical calculation. The finite element examination shows that the method provides a simple but satisfactory prediction of pipe structures in engineering plastic analysis.

• Structural Engineering and Mechanics
• /
• 제35권1호
• /
• pp.67-82
• /
• 2010

The beam string structure (BSS) has been widely applied in large span roof structures, while no analytical solutions of BSS were derived for it in the existing literature. In the first part of this paper, calculation formulas of displacement and internal forces were obtained by the Ritz-method for the most commonly used arc-shaped BSS under the vertical uniformly distributed load and the prestressing force. Then, the failure mode of BSS was proposed based on the static equilibrium. On condition the structural stability was reliable, BSS under the uniformly distributed load would fail by tensile strength failure of the string, and the beam remained in the elastic or semi-plastic range. On this basis, the limit load of BSS was given in virtue of the elastic solutions. In order to verify the linear elastic and limit state solutions proposed in this paper, three BSS modal were tested and the corresponding elastoplastic large deformation analysis was performed by the ANSYS program. The proposed failure mode of BSS was proved to be correct, and the analytical results for the linear elastic and limit state were in good agreement with the experimental and FEM results.

• 한국구조물진단유지관리공학회 논문집
• /
• 제26권6호
• /
• pp.212-221
• /
• 2022

이 연구에서는 국내 도로교량 평가에서도 설계와 일관성이 있도록 한계상태설계법에 상응하는 평가방법을 마련하고, 선진국과 같이 평가에서 목표신뢰도지수를 감소시키는 경우 신뢰도분석을 통하여 보정하여 평가 활하중계수를 제안한다. 국내 대표 교량형식을 대상으로 수집한 실교량 자료를 활용하여 각 설계기준 별 설계활하중에 대한 하중효과를 산정하여 비교한다. 현행 설계법에 의해 산정된 하중효과를 바탕으로 최소요구강도를 산정하여 이에 대한 신뢰도분석을 통해 활하중계수 보정을 수행한다. 설계수준에 비하여 낮춰진 평가수준의 활하중계수를 교량 안전성평가를 수행하고, 이전 설계법의 안전성평가 결과와 비교하여 평가결과가 증가함을 확인하였다.

• 한국자동차공학회논문집
• /
• 제22권4호
• /
• pp.121-130
• /
• 2014

This paper is the second investigation on the effects of intake flow control methods on the part load performance in a spark ignition engine. In the previous work, two control methods, port throttling and masking, were compared with respect to lean misfire limit, fuel consumption and emissions. In this work, the effects of these two methods on EGR characteristics were studied and simultaneously the differences between EGR and lean combustion as a dilution method were investigated. The results show that EGR limit is expanded up to 23% and 3 ~ 5% improvement in the fuel consumption are achieved around 8 ~ 13% rates by the flow controls comparing with 10% limit and 1.5% reduction around 3% rate of non-control case. The masking method is more effective on the limit expansion than throttling as like as lean misfire limit; however there is no substantial difference in fuel consumptions improvement regardless the control methods except high load condition. Also it is observed that there exist critical EGR rates around which the combustion performance and NOx formation change remarkably and these rates generally coincide with optimum rates for the fuel consumption. In addition, dilution with fresh air is much more advantageous than that of the exhaust gas from the view point of dilution limit and fuel consumption, while utilization of the exhaust gas is more effective on NOx reduction in spite of considerably small dilution compared with the use of fresh air. Finally, the improvement of fuel consumption by massive EGR is highly dependent on the EGR limit at which the engine runs stably, therefore the stratified combustion technique might be a best solution for this purpose.

• 한국터널지하공간학회 논문집
• /
• 제20권1호
• /
• pp.99-118
• /
• 2018

최근 토목구조물의 설계에 있어 한계상태설계법 적용이 세계적인 추세이나, 국내에서는 소수의 구조물에 국한되어 사용되고 있다. 주요 지중구조물인 터널에 대해서는 한계상태설계법의 도입이 근래에 시도되고 있으므로, 최신의 한계상태 설계법에 대한 이해가 반드시 필요하다. 본 연구는 최근 발간된 AASHTO LRFD Road Tunnel Design and Construction Guide Specification (2017)을 토대로 세그먼트 터널라이닝 설계 시 구조물 하중계수, 하중조합 등을 고찰하고 이외에 구조 검토 시 반영되어야 할 다양한 영향인자에 대해 분석하였다. 본 연구에서는 국내에 적용되고 있는 전력구, 지하철 터널 단면을 대상으로 한 세그먼트 라이닝의 구조해석을 통하여, 지반조건과 하중수정계수, 이음부 강성조건 등 다양한 영향인자들이 부재력에 미치는 영향을 분석 평가하였다.

• 대한기계학회논문집
• /
• 제17권9호
• /
• pp.2223-2233
• /
• 1993

An engineering method is suggested to calculate the applied load versus crack extension in the elastic-plastic fracture. The condition for an increment of crack extension is set by a critical increment of crack-up opening displacement(CTOD). The ratio of the CTOD increment to the incremental crack extention is a critical crack-tip opening angle(CTOA), assumed to be constant for a material of a given thickness. The Dugdale model of crack-tip deformation in an infinite plate is applied to the method, and a complete solution for crack extension and crack instability is obtained. For finite-size specimens of arbitrary geometry in general yielding, an approximate generalization of the Dugdale model is suggested so that the approximation approaches the small-scale yielding solution in a low applied load and the finite-element solution in a large applied load. Maximum load is calculated so that an applied load attains either a limit load on an unbroken ligament or a peak load during crack extension. The proposed method was applied to three-point bend specimens of a carbon steel SM45C in various sizes. Reasonable agreements are found between calculated maximum loads and experimental failure loads. Therefore, the method can be a viable alternative to the J-R curve approach in the elastic-plastic fracture analysis.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2003년도 추계학술대회 논문집 전력기술부문
• /
• pp.488-490
• /
• 2003

This paprer presents the evlauation method for transmission marginal loss factors(MLFs) considering the electrical distance. Generally, MLFs are represented as the sensitivity of transmission losses, which is computed from the change of generation by the change of the load. MLFs are classified as load-focused MLFs and generator-focused MLFs. The existing evaluation method for generator focused MLFs has the limit not reflecting the characteristic of power systems since the method has been introduced the assumption which the output of a generator is supplied to all of the load buses on the power system. Therefore, to overcome the limit of evaluation method for generator-focused MLFs, we have applied the process, which it approximately can find the load buses that supplied a generator to the method. We have applied the proposed method to the simple 5-bus system because the proposed method is not analytic but the hybrid method incorporated the Kirschen and Bialek's algorithm to the existing analytic method to find the load buses supplied by a generator.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2006년도 춘계 학술발표회 논문집
• /
• pp.1287-1294
• /
• 2006

A pile is compressed with settlements when loading and bearing capacity is altered along relative displacement of pile/soil on settlement and compression. Settlements of pile displaying limit skin friction is different from displaying tip resistance. Therefore, it is an error in traditional method that bearing capacity of pile is estimated from the sum of limit skin fraction and tip resistance. Accordingly, development of design method considering behavior of load-settlement is needed. In this study, we would like to establish the base for development of design method considering bearing capacity altering along displacement on settlement and compression. For this, we established system and substance of design method. And in order to establish relationship of load-settlement of pile on the type of soil, we analyzed and arranged existing database and pile loading test. On design method, settlement is assumed gradually on each capacity level being assumed gradually. Bearing capacity developing on the pile is obtained on each settlement level. Until the obtained bearing capacity will be equal to assumed capacity, this process is continued with increasing settlement. Load-settlement curve for soil classification is sketched in the process computing settlement on assumed capacity. This design method will be materialized by computation program.

• Structural Engineering and Mechanics
• /
• 제71권2호
• /
• pp.165-173
• /
• 2019

This paper investigates the probability of failure of reinforced concrete beams for limit state of collapse for flexure and shear. The influence of randomness of the variables on the failure probability is also examined. The Indian standard code for plain and reinforced concrete IS456:2000 is used for the design of beams. Probabilistic models are developed for flexure and shear according to IS456:2000. The loads considered acting on the beam are live load and dead load only. Random variables associated with the limit state equation such as grade of concrete, grade of steel, live load and dead load are identified. Probability of failure is evaluated based on the limit state equation using First Order Reliability Method (FORM). Importance of the random variables on the limit state equations are observed and the variables are accordingly reduced. The effect of the reduced parameters is checked on the probability of failure. The results show the role of each parameter on the design of beam. Thus, the Indian standard guidelines for plain and reinforced concrete IS456:2000 is investigated with the probabilistic and risk-based analysis and design for a simple beam. The results obtained are also compared with the literature and accordingly some suggestions are made.

• 대한전기학회논문지:전력기술부문A
• /
• 제49권2호
• /
• pp.78-84
• /
• 2000

This paper introduces a method of determining the maximum real power transfer limit of interface lines, which connect two areas of a power system, using locally parameterized continuation algorithm. This method traces the path of power flow solutions as interface flow is gradually increased under a certain load demand condition and finds the steady state voltage stability limit, the interface flow limit. Voltage stability index is used to indicate how close the maximum limit is reached. Also, this study presents a procedure to determine the security-constrained interface flow limit using the above method. Contingency ranking index is proposed to identify the severity of contingencies. The case study is performed according to the suggested procedure.