Browse > Article
http://dx.doi.org/10.7467/KSAE.2014.22.4.121

Effect of Intake Flow Control Method on Part Load Performance in SI Engine(2) - EGR Characteristics and Comparison of Dilution Method  

Kang, Min Gyun (Delphi Korea Technical Center)
Ohm, Inyong (Department of Mechanical & Automotive Engineering, Seoul National University of Science and Technology)
Publication Information
Transactions of the Korean Society of Automotive Engineers / v.22, no.4, 2014 , pp. 121-130 More about this Journal
Abstract
This paper is the second investigation on the effects of intake flow control methods on the part load performance in a spark ignition engine. In the previous work, two control methods, port throttling and masking, were compared with respect to lean misfire limit, fuel consumption and emissions. In this work, the effects of these two methods on EGR characteristics were studied and simultaneously the differences between EGR and lean combustion as a dilution method were investigated. The results show that EGR limit is expanded up to 23% and 3 ~ 5% improvement in the fuel consumption are achieved around 8 ~ 13% rates by the flow controls comparing with 10% limit and 1.5% reduction around 3% rate of non-control case. The masking method is more effective on the limit expansion than throttling as like as lean misfire limit; however there is no substantial difference in fuel consumptions improvement regardless the control methods except high load condition. Also it is observed that there exist critical EGR rates around which the combustion performance and NOx formation change remarkably and these rates generally coincide with optimum rates for the fuel consumption. In addition, dilution with fresh air is much more advantageous than that of the exhaust gas from the view point of dilution limit and fuel consumption, while utilization of the exhaust gas is more effective on NOx reduction in spite of considerably small dilution compared with the use of fresh air. Finally, the improvement of fuel consumption by massive EGR is highly dependent on the EGR limit at which the engine runs stably, therefore the stratified combustion technique might be a best solution for this purpose.
Keywords
EGR; Dilution rate; Lean misfire limit; Port throttling; Port masking; Stratification; Fuel consumption;
Citations & Related Records
Times Cited By KSCI : 8  (Citation Analysis)
연도 인용수 순위
1 J. B. Heywood, Internal Combustion Engine Fundamentals, Int. Edn., pp. 281-282, McGraw-Hill, Singapore, 1988.
2 G. T. Kalghatgi, "Spark Ignition, Early Flame Development and Cyclic Variation in IC Engines," SAE 870163, 1987.
3 A. A. Quader, "The Axially-stratified-charge Engine," SAE 820131, 1982.
4 K. Horie, K. Nishizawa, T. Ogawa, S. Akazaki and K. Miura, "The Development df a High Fuel Economy and High Performance Four Valve Lean Burn Engine," SAE 920455, 1992.
5 T. Inoue, S. Matsushita, K. Nakanishi and H. Okano, "Toyota Lean Combustion System-The Third Generation System," SAE 930873, 1993.
6 I. Y. Ohm, H. S. Ahn, W. J. Lee, W. T. Kim, S. S. Park and D. U. Lee, "Development of HMC Axially Stratified Lean Combustion Engine," SAE 1993 Transactions 103(3), pp.1298-1311, 1994.
7 C. Park, Y. Choi and C. Kim, "Study on Fuel Consumption Improvement in SI Engine with EGR for Hybrid Electric Vehicle," Transactions of KSAE, Vol.16, No.2, pp.128-135, 2008.   과학기술학회마을
8 C. Park, Y. Choi and C. Kim, "Analysis of Performance and Emissions Characteristics on Gasoline Engine for Hybrid Vehicles with Optimum EGR Rate and the Cylinder Variation of EGR Rate," Transactions of KSAE, Vol.17, No.1, pp.87-95, 2009.   과학기술학회마을
9 D. Kim, S. Kim, S. Lee and J. Lim, "A Study of Fuel Economy Improvement Potential on US Fuel Economy Test Cycles by Model Based Development of Cooled HP-EGR System on GDI Engine," KSAE Spring Conference Proceedings, pp.191-196, 2012.
10 I. Y. Ohm, K. S. Jeong and I. S. Jeung, "Effects of Injection Timing on the Lean Misfire Limit in an SI Engine," SAE 1997 Transactions 106(3), pp.42-55, 1998.
11 I. Y. Ohm, K. S. Jeong, Y. Yoon and I. S. Jeung, "Initial Flame Development under Fuel Stratified Condition," SAE 1998 Transactions 107(3), pp.1796-1807, 1999.
12 I. Y. Ohm and C. J. Park, "Experimental Study on Axial Stratification Process and Its Effects (1)," KSME International Journal, Vol.16, No.11, pp.1457-1469, 2002.   과학기술학회마을
13 I. Y. Ohm and C. J. Park, "Effect of Fuel Stratification on Initial Flame Development: Part 2-low Swirl Condition," Int. J. Automotive Technology, Vol.9, No.6, pp.671-678, 2008.   과학기술학회마을   DOI
14 I. Y. Ohm and C. J. Park, "Effect of Fuel Stratification on Initial Flame Development: Part 3-high Swirl Condition," Int. J. Automotive Technology, Vol.12, No.5, pp.653-660, 2011.   과학기술학회마을   DOI   ScienceOn
15 M. G. Kang and I. Ohm, "Effect of Intake Flow Control Method on Part Load Performance in SI Engine-Comparison of Throttling and Masking," Transactions of KSAE, Vol.22, No.2, pp.156-165, 2014.   과학기술학회마을   DOI   ScienceOn
16 S. Kim, S. Lee, D. Kim, I. Ohm and Y. Cho, "EGR Ratio Estimation Using Predictions of In-cylinder Residual Gas Fraction in SI Engines," Transactions of KSAE, Vol.12, No.1, pp.55-60, 2004.
17 I. Ohm, "Combustion Characteristics of Landfill Gas in a Constant Volume Combustion Chamber for Large Displacement Volume Engine(I)-Fundamental Characteristics," Transaction of KSME-B, Vol.37, No.8 pp.733-741, 2013.   과학기술학회마을   DOI   ScienceOn