• Journal of the Korean Vacuum Society
• /
• v.21 no.4
• /
• pp.185-192
• /
• 2012

p-n junction temperature and thermal resistance of Light Emitting Diode (LED) package are affected by the chip size due to the change of the thermal density and the external quantum efficiency considering the heat dissipation through conduction. In this study, forward voltage was measured for two different size LED chips, 24 mil and 40 mil, which consist constitute 16-chip package. p-n junction temperature and thermal resistance were determined by thermal transient analysis, which were discussed in connection with the electrical characteristics of the LED chip and the structure of the LED package.

• Journal of the Optical Society of Korea
• /
• v.18 no.4
• /
• pp.370-376
• /
• 2014

We optimized the design of the flat encapsulant of a light-emitting diode (LED) package to obtain higher light output power (LOP), both by experiment and simulation using three-dimensional ray-tracing software. In the experiment, the refractive index of the encapsulant was varied (1.41 and 1.53). In addition, double-layer structures with these refractive indices (1.41/1.53) were investigated by varying the shape of the interface between the two among flat, concave, and convex. The experiments showed that the LOP of the double-layer encapsulant with convex interface increased by 13.4% compared to the single-layer encapsulant with a refractive index 1.41, which was explained by the increase of the light extraction efficiency (LEE) in connection with the increase of the critical angle (${\theta}_c$) and the decrease of the Fresnel reflection.

• Journal of Advanced Marine Engineering and Technology
• /
• v.39 no.8
• /
• pp.801-806
• /
• 2015

The experimental analysis of a crevice-type vapor chamber heat pipe (CVCHP) is investigated. The heat source of the CVCHP is a high-power light-emitting diode (LED). The CVCHP, which exhibits a bubble pumping effect, is used for heat dissipation in a high-heat-flux system. The working fluid is R-141b, and its charging ratio was set at 60 vol.% of the vapor chamber in a heat pipe. The total thermal conductivity of the falling-liquid-film-type model, which was a modified model, was 24% larger than that of the conventional model in the LED package. Flow visualization results indicated that bubbles grew larger as they combined. These combined bubbles pushed the working fluid to the top, partially wetting the heat-transfer area. The thermal resistance between the vapor chamber and tube in the modified design decreased by approximately 32%. The overall results demonstrated the better heat dissipation upon cooling of the high-power LED package.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2007.08b
• /
• pp.1703-1705
• /
• 2007

Before the ultra-violet glue encapsulation, the research evaporated LiF thin film on device surface to be the extra packaging layer for improving the lifetime of organic light-emitting diode. The formula of UV glue was specially developed. We found 100 nm LiF is the optimum thickness. The best lifetime obtained by using LiF and special UV glue is 2.4 times longer than those by commercial UV glue.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.18 no.4
• /
• pp.175-182
• /
• 2017

In light emitting diode (LED) chip packaging, wire bonding is an important process that connects the LED chip on the lead frame pad with the Au wire and enables electrical operation for the next process. The wire bonding process is divided by two types: thermo compression bonding and ultrasonic bonding. Generally, the wire bonding process consists of three steps: 1st ball bonding that bonds the shape of the ball on the LED chip electrode, looping process that hangs the wire toward another connecting part with a loop shape, and 2nd stitch bonding that forms and bonds to another electrode. This study analyzed the factors affecting the LED die bonding processes to optimize the process capability that bonds a small Zener diode chip on the PLCC (plastic-leaded chip-carrier) LED package frame, and then applied response surface analysis. The design of experiment (DOE) was established considering the five factors, three levels, and four responses by analyzing the factors. As a result, the optimal conditions that meet all the response targets can be derived.

• Proceedings of the KIPE Conference
• /
• 2004.07a
• /
• pp.321-324
• /
• 2004

This paper presents a package IC containing some components of DC/DC converter block for mobile phone's sub OLED(Organic Light Emitting Display). Package IC contains a load switch, a control IC, a diode, a switch for on/off operation, and a switch for changing output voltage. It operates with switching frequency of 100kHz, within the range of input voltage, $3.2V\~5.5V$. Duty ratio can be changed up to $93\%$, and maximum power efficiency is $85\%$. This package IC is loaded onto three model of 1.2W mobile phone's sub-OLED.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2011.06a
• /
• pp.1163-1164
• /
• 2011

• International Journal of Aerospace System Engineering
• /
• v.1 no.1
• /
• pp.44-47
• /
• 2014

This study proposes a development for the nano silver adhesive, which is applicable to high efficiency LED(light-emitting diode) light. The important issue of LED light is heat exhaust from LED. Generally, the middle area of LED light is increased up to 380K. Therefore, the bottleneck between LED chip and heat sink are caused by high temperature. In this work, the adhesive material between LED Chip and heat sink was newly developed for improvement of bottleneck. The nano silver was adopted to solve heat problem of chip on board package for LED light. In order to evaluate the performance of the nano silver adhesive, the thermal analysis was performed. Moreover both adhesive performance and heat exhaust were verified through the prototype test. From the experimental test results, it is found that the developed nano silver adhesive has the high performance.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2005.10a
• /
• pp.882-884
• /
• 2005

A new rectangular shape microlens array having high sag for solid-state lighting is presented. Proposed microlens, which has high sag, over $375{\mu}m$ and large diameter, over 3 mm can enormously enhance output optical extraction efficiency. Rectangular shape of microlens can maximize the fill factor of light-emitting-diode (LED) package and minimize the optical loss at the same time. This wafer level microlens array is fabricated on LED package. It has many advantages in optical properties, low cost, high aligning accuracy, and mass production.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2009.06a
• /
• pp.315-316
• /
• 2009

본 논문에서는 1W 급 이상의 고출력 LED 용 패키지로서 세라믹 LTCC 적층 패키지의 방열 특성을 평가하고 열해석 결과와의 차이에 대해 고찰하였다. 특히, 세라믹 패키지의 방열 특성을 향상시키기 위해 Thermal Via와 Heat slug를 LED Chip 하단부에 위치시켰을 때 방열 특성을 평가하기 위해 Transient Thermal Test를 이용하여 각각의 경우에 대한 열저항을 평가하여 방열 특성의 항상 정도를 확인하였으며, 열해석 시뮬레이션을 통해 얻은 결과와 비교하였다. 평가 결과 Heat slug를 배치한 패키지가 열저항이 $8^{\circ}C/W$로서 가장 우수한 특성을 보여주었으며, 열해석 결과와의 차이에 대해서는 광출력으로 방출된 전력을 계산하여 보정함으로써 $1^{\circ}C$ 이하의 편차를 보여주는 결과를 얻을 수 있었다.