• Journal of Radiation Industry
• /
• v.11 no.3
• /
• pp.157-165
• /
• 2017

In this paper, we calculate the light photons collection efficiency of large-volume plastic scintillation detector mainly used for radiation portal monitor (RPM). A Monte Carlo light photon transport code, DETECT2000, were used to quantitatively evaluate light collection efficiency of plastic scintillation detector. DETECT2000 calculated the placement of light collection efficiency based on the energy spectrum. We calculated the light collection efficiency relative to the position of the energy spectrum that proportional to the placement of the source. The $850{\times}285{\times}65mm^3$ size of polyvinyl toluene (PVT) scintillator was used for measurements. Through DETECT2000 simulation, the light collection efficiency of $5{\times}5$ arrays were calculated and verification was performed by comparing with experimentally measured. And then, the corrected MCNP simulation by applying the light collection efficiency in $21{\times}13$ arrays was compared and analyzed. Comparing the Monte Carlo simulation with measured results, it shows an average difference of 10.1% in $5{\times}5$ arrays. Particularly, about twice of the difference was found in the edge of first column, which coupled with PMT. In whole $5{\times}5$ array, the overall ratio was the same except for the first column. And then comparing the energy spectra of the $21{\times}13$ array with and without the light collection efficiency, it shows a difference of 6.69% in Compton edge area. The DETECT2000 based light collection efficiency simulation showed well agreement with the point source experiment. And comparing with measured energy spectra, we could compare the differences according to whether or not the light collection efficiency was applied. As a results, it is possible to increase the accuracy and reliability of Monte Carlo simulation results by pre-calculating the light collection efficiency according to the PVT geometry by using the DETECT2000.

• KSII Transactions on Internet and Information Systems (TIIS)
• /
• v.14 no.8
• /
• pp.3501-3518
• /
• 2020

The method of DNS data collection is one of the most important parts of DNS simulation. DNS data contains a lot of information. When it comes to analyzing the DNS security issues by simulation on the cyber range with customized features, we only need some of them, such as IP address, domain name information, etc. Therefore, the data we need are supposed to be light-weighted and easy to manipulate. Many researchers have designed different schemes to obtain their datasets, such as LDplayer and Thales system. However, existing solutions consume excessive computational resources, which are not necessary for DNS security simulation. In this paper, we propose a light-weighted active data collection method to prepare the datasets for DNS simulation on cyber range. We evaluate the performance of the method and prove that it can collect DNS data in a short time and store the collected data at a lower storage cost. In addition, we give two examples to illustrate how our method can be used in a variety of applications.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.24 no.6
• /
• pp.515-520
• /
• 2012

A daylighting system includes three parts; light collector, light transformer and light distributor. A DBLP(Double blind light pipe) daylighting system consists of a double blind light collector, a mirror duct type light transformer and a prism film light pipe distributor. The double blinds for a light collection are used to track the sun's altitude and azimuth movements throughout the day. Behind both sets of blinds is the light transformer, which is based on a rectangular cone shaped light duct. The light transformer was designed to efficiently deliver the light into the light pipe within a 30 degree radial spread for the efficient light into the distributor. In this study, DBLP system efficiency was simulated, evaluated and optimized by Tracepro as a popular ray trace light design simulation program. The results indicated that DBLP system efficiency evaluated a maximum 22.4% in case of Spring/Fall season solar noon time. While the overall average system efficiency in the morning and afternoon is evaluated about 10%.

• Nuclear Engineering and Technology
• /
• v.47 no.4
• /
• pp.479-487
• /
• 2015

The thallium-doped sodium iodide [NaI(Tl)] scintillation detector is preferred as a gamma spectrometer in many fields because of its general advantages. A silicon photomultiplier (SiPM) has recently been developed and its application area has been expanded as an alternative to photomultiplier tubes (PMTs). It has merits such as a low operating voltage, compact size, cheap production cost, and magnetic resonance compatibility. In this study, an array of SiPMs is used to develop an NaI(Tl) gamma spectrometer. To maintain detection efficiency, a commercial NaI(Tl) $2^{\prime}{\times}2^{\prime}$ scintillator is used, and a light guide is used for the transport and collection of generated photons from the scintillator to the SiPMs without loss. The test light guides were fabricated with polymethyl methacrylate and reflective materials. The gamma spectrometer systems were set up and included light guides. Through a series of measurements, the characteristics of the light guides and the proposed gamma spectrometer were evaluated. Simulation of the light collection was accomplished using the DETECT 97 code (A. Levin, E. Hoskinson, and C. Moison, University of Michigan, USA) to analyze the measurement results. The system, which included SiPMs and the light guide, achieved 14.11% full width at half maximum energy resolution at 662 keV.

• Proceedings of the Korean Nuclear Society Conference
• /
• 2002.05a
• /
• pp.444.1-444
• /
• 2002

• KIEAE Journal
• /
• v.13 no.2
• /
• pp.61-66
• /
• 2013

This study is to eliminate the need for conventional high density plant factory's artificial light source such as LED to reduce the initial investment of the light source installation as well as the operation cost. Use of solar light could enhance the quality of the vegetables similar to those grown in the natural environment. Provision of solar light into the multilayer vegetable cultivation facilities and collecting maximum and sustainable sunlight without too much loss by tracing solar path and properly distributing it through careful control during daytime are crucial for realizing the investigated rooftop light shelf system for multi-layered vegetable cultivation. In this study, we developed an innovative way of effectively allocating sunlight inside even to otherwise shaded zone of a multi-layer vegetable cultivation facility. To prove the effectiveness of the system's sunlight collection and distribution capability, both simulation and experiment in Daejeon are performed and the outcome is analyzed.

• Journal of KIISE:Computer Systems and Theory
• /
• v.36 no.5
• /
• pp.422-428
• /
• 2009

NAND flash memory is widely used in embedded systems because of many attractive features, such as small size, light weight, low power consumption and fast access speed. However, it requires garbage collection, which includes erase operations. Erase operation is slower than other operations. Further, a block has a limited erase lifetime (typically 100,000) after which a block becomes unusable. The proposed garbage collection policy focuses on minimizing the total number of erase operations, the deviation value of each block and the garbage collection time. NAND flash memory consists of pages of three types, such as valid pages, invalid pages and free pages. In order to achieve above goals, we use a page ratio to decide when to do garbage collection and to select the target victimblock. Additionally, we implement allocating method and group management method. Simulation results show that the proposed policy performs better than Greedy or CAT with the maximum rate 85% of reduction in the deviation value of the erase operations and 6% reduction in garbage collection time.

• Journal of KIISE:Computing Practices and Letters
• /
• v.15 no.9
• /
• pp.617-625
• /
• 2009

NAND flash memory is widely used in embedded systems because of many attractive features, such as small size, light weight, low power consumption and fast access speed. However, it requires garbage collection, which includes erase operations. Erase operation is very slow. Besides, the number of the erase operations allowed to be carried out for each block is limited. The proposed garbage collection method focuses on minimizing the total number of erase operations, the deviation value of each block and the garbage collection time. NAND flash memory consists of pages of three types, such as valid pages, invalid pages and free pages. In order to achieve above goals, we use a page rate to decide when to do garbage collection and to select the target victim block. Additionally, We implement allocating method and group management method. Simulation results show that the proposed policy performs better than Greedy or CAT with the maximum rate at 82% of reduction in the deviation value of erase operation and 75% reduction in garbage collection time.

• Journal of the Korean Society of Radiology
• /
• v.17 no.5
• /
• pp.671-677
• /
• 2023

When a scintillator block is constructed using fine scintillator pixels, the scintillator block located at the edge of the scintillator block results in overlapping images. To solve this problem, a light guide was inserted between the scintillator block and the photosensor, and images of all scintillation pixels were separated and acquired. However, loss of light may occur through the light guide, which eventually affects the quality of the image due to a decrease in energy resolution. Therefore, in this study, a detector was designed that can separate scintilltion pixels better by using a reflector on the side of the light guide and can secre excellent energy resolution by minimizing light loss. For comparative evaluation with previous studies, flood images were obtained through DETECT2000 capable of light simulation, and the degree of separation and light collection rate were evaluated. When a reflector was used on the side of the light guide, all materials showed excellent separation regardless of the material of the light guide, which showed better separation results than previous studies. In addition, the light collection rate was more that five times better when the reflector was applied than when it wa not. If this detector is applied to a small animal positron emission tomography, it will be possilbe to secre excellent image quality through excellent spatial resolution and energy resolution.

• Proceedings of the KIEE Conference
• /
• 1994.07b
• /
• pp.1277-1279
• /
• 1994

In the structure of ZnO/nip-SiC: H/metal substrate amorphous silicon (a-Si:H) solar cells, the effects of inserting a rear textured ZnO in the p-SiC:H/metal interface and a graded bandgap buffer layer in the i/p-SiC:H have been analysed by computer simulation. The incident light was taken to have an intensity of $100mW/cm^2$(AM-1). The thickness of the a-Si:H n, ${\delta}$-doped a-SiC:H p, and buffer layers was assumed to be $200{\AA},\;66{\AA}$, and $80{\AA}$, respectively. The scattering coefficients of the front and back ZnO were taken to be 0.2 and 0.7, respectively. Inserting the rear buffer layer significantly increases the open circuit voltage($V_{oc}$) due to reduction of the i/p interface recombination rate. The use of textured ZnO markedly improves collection efficiency in the long wavelengths( above ${\sim}550nm$ ) by back scattering and light confinement effects, resulting in dramatic enhancement of the short circuit current density($J_{sc}$). By using the rear buffer and textured ZnO, the i-layer thickness of the ceil for obtaining the maximum efficiency becomes thinner(${\sim}2500{\AA}$). From these results, it is concluded that the use of textured ZnO and buffer layer at the backside of the ceil is very effective for enhancing the conversion efficiency and reducing the degradation of a-Si:H pin-type solar cells.