• Environmental Engineering Research
• /
• v.25 no.1
• /
• pp.88-95
• /
• 2020

An investigation of rare metals recovery from LiNi_xCo_yMn_zO₂ cathode material of the end-of-life lithium-ion batteries is presented. To determine the influence of reductant on the leach process, the cathode material (containing Li 7.6%, Co 20.4%, Mn 19.4%, and Ni 19.3%) was leached in H₂SO₄ solutions either with or without H₂O₂. The optimal process parameters with respect to acid concentration, addition dosage of H₂O₂, temperature, and the leaching time were found to be 2.0 M H₂SO₄, 4 vol.% H₂O₂, 70℃, and 150 min, respectively. The yield of metal values in the leach liquor was > 99%. The leach liquor was subsequently treated by precipitation techniques to recover nickel as Ni(C₄H₇N₂O₂)₂ and lithium as Li₂CO₃ with stoichiometric ratios of 2:1 and 1.2:1 of dimethylglyoxime:Ni and Na₂CO₃:Li, respectively. Cobalt was recovered by solvent extraction following a 3-stage process using Na-Cyanex 272 at pH_eq ~5.0 with an organic-to-aqueous phase ratio (O/A) of 2/3. The loaded organic phase was stripped with 2.0 M H₂SO₄ at an O/A ratio of 8/1 to yield a solution of 114 g/L CoSO₄; finally recovered CoSO₄.xH₂O by crystallization. The process economics were analyzed and found to be viable with a margin of $476 per ton of the cathode material.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2007.11a
• /
• pp.255-256
• /
• 2007

In the study, in order to develop low temperature sintering ceramics for multilayer piezoelectric actuator, PMN-PNN-PZT ceramics were fabricated using $Na_2CO_3,\;Li_2CO_3$ as sintering aids and their dielectric and piezoelectric properties were investigated according to the variations of $MnO_2$ as additives and sintering aids. At the sintering temperature of $900^{\circ}C$ and 0.1wt% $MnO_2$ as sintering aids, density, electromechanical coupling factor$(k_p)$, mechanical quality factor$(Q_m)$, piezoelectric constant$(d_{33})$, and dielectric constant $({\varepsilon}_r)$ showed the optimum value of $7.87[g/cm^3]$, 0.61, 1131, 1127 and 376, respectively, for multilayer piezoelectric actuator application.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2005.07a
• /
• pp.593-594
• /
• 2005

Lithium-ion batteries have used the layered $LiCoO_2$ materials as cathodes, but Co is relatively toxic and expensive. In this regard, the spinel $LiMn_2O_4$ has become appealing because manganese is inexpensive and environmentally benign. In general, cathodes for lithium ion batteries include carbon as a conductive agent that provides electron transfer between the active material and the current collector. In this work, we selected Acetylene Black and Super P Black as conducting agents, and then carried out comparative investigation for the performances of the cells using different conducting agents with different particle size. As a consequence, Li/$LiMn_2O_4$ cells with Super P Black show better electrochemical performances than those with Acetylene Black.

• Bulletin of the Korean Chemical Society
• /
• v.28 no.12
• /
• pp.2226-2230
• /
• 2007

As a cathode material of lithium rechargeable batteries, charged Li[Co0.1Ni0.15Li0.2Mn0.55]O2 electrodes, which were aged thermally at 25 oC and 90 oC respectively, were characterized by means of charge/discharger, impedance spectroscopy, and X-ray diffraction. The discharge capacity diminution of the electrodes aged at 25 oC and 90 oC for 1 week was 4% and 23%, respectively. The cell aged at 25 oC was recovered on cycling. However, the capacity loss after ageing at 90 oC was not recovered in a subsequent cycling test, which demonstrates that the reaction occurring during ageing at 90 oC is irreversible. A significant impedance increase of aged electrode at 90 oC is associated with irreversible capacity loss. The structural changes including phase transformation were not detected by XRD analysis, because it could be due to out of detection limit. After ageing, impedance was slightly decreased during subsequent cycling test. It could be explained the cyclic performance of aged sample is stable. The thermal stability was not deteriorated by ageing even at the high temperature of 90 oC.

• Journal of Electrochemical Science and Technology
• /
• v.12 no.4
• /
• pp.377-386
• /
• 2021

The Li-rich oxides are promising cathode materials due to their high energy density. However, characteristics such as low rate capability, unstable cyclic performance, and rapid capacity fading during cycling prevent their commercialization. These characteristics are mainly attributed to the phase instability of the host structure and undesirable side reactions at the cathode/electrolyte interface. To suppress the phase transition during cycling and interfacial side reactions with the reactive electrolyte, K (potassium) doping and Nb oxide coating were simultaneously introduced to a Li-rich oxide (Li_1.2Ni_0.13Co_0.13Mn_0.54O₂). The capacity and rate capability of the Li-rich oxide were significantly enhanced by K doping. Considering the X-ray diffraction (XRD) analysis, the interslab thickness of LiO₂ increased and cation mixing decreased due to K doping, which facilitated Li migration during cycling and resulted in enhanced capacity and rate capability. The K-doped Li-rich oxide also exhibited considerably improved cyclic performance, probably because the large K⁺ ions disturb the migration of the transition metals causing the phase transition and act as a pillar stabilizing the host structure during cycling. The Nb oxide coating also considerably enhanced the capacity and rate capability of the samples, indicating that the undesirable interfacial layer formed from the side reaction was a major resistance factor that reduced the capacity of the cathode. This result confirms that the introduction of K doping and Nb oxide coating is an effective approach to enhance the electrochemical performance of Li-rich oxides.

• 한국전기화학회:학술대회논문집
• /
• 2003.10a
• /
• pp.68-68
• /
• 2003

• Bulletin of the Korean Chemical Society
• /
• v.35 no.9
• /
• pp.2684-2688
• /
• 2014

Two two-dimensional cyanide- and phenoxo-bridged heterometallic M(II)-Mn(III) (M = Ni, Pd) coordination polymers $\{[Mn(saltmen)]_4[Ni(CN)_4]\}(ClO_4)_2{\cdot}CH_3OH{\cdot}H_2O$ (1) and $\{[Mn(saltmen)]_4[Pd(CN)_4]\}(ClO_4)_2{\cdot}CH_3CN{\cdot}H_2O$ (2) ($saltmen^{2-}$ = N,N'-(1,1,2,2-tetramethylethylene)bis(salicylideneaminato)dianion) have been obtained by using $K_2[M(CN)_4]$ as building blocks and a salen-tpye Schiff-base manganese(III) compound as assembling segment. Single X-ray analysis reveals their isostrutural cyanide-bridged $MMn_4$ pentanuclear cationic structure. The four Schiff base manganese units of the pentanuclear entity are self-complementary through the phenoxo oxygen atoms from the neighboring complex, therefore forming cyanide- and phenoxo-bridged 2D sheet-like structure. Investigation over magnetic susceptibilities reveals the overall ferromagnetic coupling between the adjacent Mn(III) ions bridged by the phenoxo oxygen atoms with J = 2.13 and $2.21cm^{-1}$ for complexes 1 and 2, respectively.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.41 no.2
• /
• pp.165-170
• /
• 2005

Al-Zn alloy/$MnO_2$, seawater cell was considered as a primary aqueous cell with an average voltage range from 1.0 to 1.1V, and the electrolyte of seawater was uptaken into the cell. Eventually, the capacity of its usage will be used for long-term. However, the more use of this cell, the higher corrosion phenomenon of the electrode occurred. Due to its corrosion phenomenon, one main default has been observed with gradual decrease during a discharge process. In this research, a common-used active material for anode was $LiNiO_2$. An active material for cathode, $Zn_{X}FeS_2$ was synthesized in high temperature by uptaken a small amount of 1.3 wt% of ZnS into $FeS_2$, one of the transition-metal dichalcogenides in high temperature. Consequently, based on their usages shown above, this secondary aqueous lithium cell could be more developed. This cell was shown as remarkable charge/discharge performance during the charge/discharge processes. This cathode with active material was given a considerable efficiency of inserting $Li^+$ ions. Moreever, in accordance with the characteristic of the crystal structure for $Zn_{x}FeS_2$, a small amount of ZnS was added which made it possible to reduce prominently velocity of corrosion during the charge/discharge cycle. By applying those merits, Al-Zn alloy/$MnO_2$ seawater cell will be used as a fundamental data in order to transform into a secondary aqueous cell.

• Journal of Electrochemical Science and Technology
• /
• v.14 no.4
• /
• pp.320-325
• /
• 2023

In Li-ion batteries, a thick electrode is advantageous for lowering the inactive current collector portion and obtaining a high energy density. One of the critical failure mechanisms of thick electrodes is inhomogeneous lithiation and delithiation owing to the axial location of the electrode. In this study, it was confirmed that the top layer of the composite electrode contributes more to the charging step owing to the high ionic transport from the electrolyte. A high-loading multilayered electrode containing LiFePO₄ (LFP) and LiNi_0.8Co_0.1Mn_0.1O₂ (NCM811) was developed to overcome the inhomogeneous electrochemical reactions in the electrode. The electrode laminated with LFP on the top and NCM811 on the bottom showed superior cyclability compared to the electrode having the reverse stacking order or thoroughly mixed. This improvement is attributed to the structural and interfacial stability of LFP on top of the thick electrode in an electrochemically harsh environment.

• Elastomers and Composites
• /
• v.57 no.4
• /
• pp.181-187
• /
• 2022

CdSe-Mn nanocomposites were synthesized using a microwave method with sodium sulfite (Na₂SO₃), selenium (Se), cadmium sulfate octahydrate (3CdSO₄·8H₂O), ammonia solution (NH₃·H₂O), and manganese (II) sulfate monohydrate (MnSO₄·H₂O). We obtained CdSe-Mn-C₆₀ nanocomposites by calcining CdSe-Mn nanocomposites and fullerene (C₆₀) in an electric furnace at 700 ℃ for 2 h. X-ray diffraction, Raman spectroscopy, and scanning electron microscopy were used to characterize the crystal structures, lattice vibrations, and surface morphologies of the products, respectively. The photocatalytic activities of the CdSe-Mn-C₆₀ nanocomposites were investigated based on the photocatalytic degradations of organic dyes such as BG, MB, MO, and RhB under ultraviolet (UV) irradiation at 254 nm. UV-visible spectrophotometry was used to confirm the degradation process.