• Journal of the Korean Wood Science and Technology
• /
• v.32 no.2
• /
• pp.50-57
• /
• 2004

This study attempted to evaluate the water repellency and drying effectiveness of linseed oil treated-solid wood at high temperature by immersion. The moisture content of green wood (Pinus densiflora) sample (above 90%) was reduced about 10% after 6 hours treatment at 150℃. When the treated samples were cut into cross section along the length, it was observed that the linseed oil penetrated into up to 20% of the sample cross section area in all locations. However, a strength loss of the specimen was not detected. The pre-drilling before linseed oil treatment was effective in reducing the defects such as checks and splits, and improved the linseed oil penetration into all samples from the surfaces. The result of water absorption test of treated-wood showed that the water repellent efficacy of treated-wood was greater than that of the control. The anti-fungal activity of treated samples using five sap stains and thee decay fungi was not detected in broad-spectrum toxic mechanism. However, decay test using white rot fungi (Tyromyces palustris) and brown rot fungi (Trametes versicolor) showed that the treated sample has a decay resistance to these two fungi.

• Korean Journal of Materials Research
• /
• v.2 no.3
• /
• pp.197-201
• /
• 1992

The temperature dependence of the magentic moment was determined for the system of high $T_{c}$ superconductor $Y_{1-X}Sm_{x}Ba_2Cu_3O_{7-y}$ with x=0, 0.2, 0.4, 0, 6, 0.8 and 1.0. Also the magnetic susceptibility and the magnetic critical current density were measured from the magnetic hysterisis loops obtained at 30 K. From the results of the magnetic susceptibility measurements, the high $T_{c}$ phase were ranged from 14.7 to 49.1%. The values of the magnetic critical current densities were in the range of $10^3~10^4A/cm^2$. The penetration depth was approximately ninety times larger than the coherence length.

• Journal of the Korean Vacuum Society
• /
• v.20 no.1
• /
• pp.63-69
• /
• 2011

In this study, we report on the novel lithographic patterning method to fabricate organic thin film field effect transistors (OTFTs) based on photo and e-beam lithography with well-known silicon technology. The method is applied to fabricate pentacene-based organic field effect transistors. Owing to their solubility, sub-micron sized patterning of P3HT and PEDOT has been well established via micromolding in capillaries and inkjet printing techniques. Since the thermally deposited pentacene cannot be dissolved in solvents, other approach was done to fabricate pentacene FETs with a very short channel length (~30 nm), or in-plane orientation of pentacene molecules by using nanometer-scale periodic groove patterns as an alignment layer for high-performance pentacene devices. Here, we introduce $Al_2O_3$ film grown via atomic layer deposition method onto pentacene as a passivation layer. $Al_2O_3$ passivation layer on OTFTs has some advantages in preventing the penetration of water and oxygen and obtaining the long-term stability of electrical properties. AZ5214 and ma N-2402 were used as a photo and e-beam resist, respectively. A few micrometer sized lithography patterns were transferred by wet and dry etching processes. Finally, we fabricated micron sized pentacene FETs and measured their electrical characteristics.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.18 no.3
• /
• pp.49-57
• /
• 2014

A deterioration of typical reinforced concrete (RC) bridge deck is due to the use of calcium chloride, cracks and water penetration inside of the deck slab with steel reinforcement. In order to eliminate the defects of RC decks in terms of material, therefore, the steel-strapped deck system is studied and developed by maximizing the arching effect while the girders are restrained using straps in lateral direction to the bridge. This parametric study was performed to analyze the structural characteristics of steel-strapped deck, and to identify the factors of the thickness, span length and lateral restraint stiffness of deck slab considering the concrete non-linearity. Finally, a design equation, which is adequate to South Korea, is suggested.

• Journal of the Korean Geotechnical Society
• /
• v.33 no.12
• /
• pp.21-33
• /
• 2017

This paper presents the analysis of plugging effect especially when the large diameter steel pipe pile was installed by considering driveability (BPM, blow per meter). The Coupled Eulerian-Lagrangian (CEL) technique was used to simulate the driving of open-ended piles into soil. To consider the driveability, the applied driving energy for each pile was obtained from the analysis results by using the wave equation. The parametric studies were performed for different pile diameters, penetration depths of pile, soil elastic modulus and BPM. It was found that the SPI is almost constant with increasing both the pile diameter and the required driving energy. It is also found that the plugging effect increases with increasing the pile length, resulting in the increase of lateral earth pressure. Based on this study the apparent magnitude and distribution of the lateral earth pressure is proposed for inside portion mobilizing soil plug.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.13 no.1 s.53
• /
• pp.78-87
• /
• 2009

When the steel slag is utilized to the concrete as the alternative fine aggregate, its use is limited as the concrete aggregate because of expansibility caused by much quantity of free CaO. So, this study is intended to examine the characteristics of the concrete which uses the rapidly cooled steel slag whose content of free CaO is sharply reduced by rapidly cooling the steel slag as the fine aggregate. Accordingly, by comparing and considering the results of the concrete slump loss test with the different substitution ratio and fine aggregate ratio of rapidly cooled steel slag, hydration by XRD and SEM analysis, compressive test by age, a length variation test and rapid chloride ion penetration test, the rapidly cooled steel slag's proper substitution ratio and the fine aggregate ratio was derived.

• Journal of Korean Tunnelling and Underground Space Association
• /
• v.4 no.2
• /
• pp.155-165
• /
• 2002

This paper presents a case study on the construction of a long tunnel named as "Solan tunnel", which connects between Mt. Dongbaek station and Dokye station in the Youngdong Railroad. The tunnel will be the longest tunnel with length of 16.4 km in Korea when completed. The tunnel site is located in a complex geological region with faults, cavities and coal measures. In construction of adit No. 2, geophysical investigation methods such as electrical resistivity method and GPR(Ground Penetration Radar) were used to detect faults, cavities and coal measures in advance with some success. The geophysical investigation results and in-situ boring data were used as feedback to improve tunnel reinforcement design. Also, the tube umbrellas of grouted steel pipes were found to have a good reinforcement and grouting effects in zones of faults, cavities. In zones of coal measures, swellex rockbolts with mortar grouting were verified as successful.

• Journal of the Korean GEO-environmental Society
• /
• v.15 no.1
• /
• pp.5-12
• /
• 2014

In this study, we developed the electric heating equipment and applied for soft ground improvement. The developed heat pipe is 4 m-length and consumes 1 kW/m, which is consisted of Ni-Cr wire. It was installed in 3.5~4.5 m below ground surface and heated for 96 hours (48 hours, 2 times). The temperature variation and vapor pressure caused by electric heating was measured by the thermometer and pressure gauge which were installed in the ground (5.0 m), and the tip resistances were measured by static electronic piezo-cone penetration test (CPT). As the results of experiments, 2-order polynomial curve was shown to adjust the variation of tip resistance and the temperature distribution with the horizontal distance from electric heater, whose R2 value is close to 1. In addition, in-situ pore-water pressure and water content was decreased.

• Journal of the Korean Magnetics Society
• /
• v.1 no.2
• /
• pp.15-21
• /
• 1991

The magnetic properties of the $Y_{1}Ba_{2}Cu_{3-x}Sn_{x}O_{7-y}$ superconductor were studied as a function of Sn concentration by utilizing both the vibrating sample magnetometer (VSM) and torque magnetometer. Unlike the cases where Fe and Co were substituted for Cu, the superconducting transition temperature was maintained above 90 K until x reached the value of 0.36. The lower critical field $H_{c1}(T)$ and upper critical field $H_{c2}(T)$ are measured as a function of temperature and external magnetic field, respectively. By aid of these results, $H_{c1}(0)$.($H_{c2}(0)$), the coherence length ${\varepsilon}_{0}$, the penetration depth ${\lambda}_{0}$, and the Ginzburg-Landau parameter k were oqtained. Flux pinning was also observed in the sample.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.12 no.5
• /
• pp.2005-2010
• /
• 2011

Since recently exhaust gas regulation for a non-road small engine as well as commercial vehicle engine has been enforced, a carburettor of a small engine should be replaced by an electronic fuel injection system. In this study, the spray characteristics of the 400cc gasoline small engine injector has been experimentally analyzed. Based on the experimental results, suitable injector for the small engine has been selected. Through the test rig measuring spray mass distribution, fuel distribution characteristics of 3 hole- and 6 hole-injector has been analyzed. Through the visualization equipment, injector spray angle, penetration length and spray width have been measured and analyzed. Considering spray characteristics and stability, 6 hole-injector is selected for the 400cc gasoline small engine.