• 대한조선학회 특별논문집
• /
• 대한조선학회 2007년도 특별논문집
• /
• pp.135-141
• /
• 2007

CSR(Common Structure Rules) enter into force on $1^{st}$ April 2006. Generally for double hull tankers of less than 150m in length, the Rules of the individual Classification Society are to be applied. Where high tensile stresses act through an intermediate plate, increased fillet welds or penetration welds are to be used longitudinal/transverse bulkhead primary support member end connections to the double bottom. If workers have begun to make used of established procedures between corrugated BHD and lower stool joint, first to welding on groove of face and then it has to gouging to blow on groove of root. So amount of man-hour increased, productivity secreased.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2002년도 추계학술대회 논문집
• /
• pp.800-803
• /
• 2002

This investigation describes and analyses the experimental results proper to the penetration of Al5052-H34 alloy plates of thickness 6, 12 and 16mm(T/D＝1, 2, 3) by 5.56mm ball projectiles over the velocity range 350-750㎧. All the high velocity impact tests were carried out at normal impact angle, i.e. zero obliquity. The experimental results presented the variation of depth of penetration, bulge height and diameter, plugged length and diameter with the velocity fur tests on each plate of a given thickness in order to determine the deformation shapes of 5.56mm ball projectiles and targets. Also the protection ballistic limit($V_50$) tests were conducted.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2004년도 추계 학술발표회 제16권2호
• /
• pp.125-128
• /
• 2004

This study concerns the new estimated strength equation of concrete by penetration test. There are not only few estimate strength equations of concrete, but also many problems to apply them because of time, cost, easiness, structural damage, reliability and so on. In this study, there performed a series of penetration test with in 730days' concrete structures and proposed equations as follows; $$Linear\;:\;f_{ck}=2.95d-80.0(r^2= 69.8\%)$$ $$Quadratic\;:\;f_{ck}=0.204d^2-12.15d+193.2(r^2=83.6\%)$$ here, fck : Estimated compressive strength of concrete by MPa d: exposed probe length by mm.

• 한국분무공학회지
• /
• 제19권4호
• /
• pp.188-196
• /
• 2014

The spray and combustion characteristics of n-dodecane fuel were investigated in a CVCC (constant volume combustion chamber). The selection of ambient conditions for the spray followed ECN (engine combustion network) guidelines, which simulates the ambient condition of diesel engines at start of fuel injection. ECN is a collaboration network whose main objective is to establish an internet library of well-documented experiments that are appropriate for model validation and the advancement of scientific understanding of combustion at conditions specific to engines. Therefore repeatability of the experiments with high accuracy was important. The ambient temperature was varied from 750 to 930 K while the density was fixed at around $23kg/m^3$. The injection pressure of the fuel was varied from 500 to 1500 bar. The spray was injected in both non-reacting ($O_2$ concentration of 0%) and reacting conditions ($O_2$ concentration of 15%) to examine the spray and the combustion characteristics. Direct imaging with Mie Scattering was used to obtain the liquid penetration length. Shadowgraph was implemented to observe vapor length and lift-off length at non-reacting and reacting conditions, respectively. Pressure data was analyzed to determine the ignition delay with respect to the spray and ambient conditions.

• 한국분무공학회지
• /
• 제28권1호
• /
• pp.32-42
• /
• 2023

In this study, spray characteristics of n-heptane and propane were investigated under different injection pressure using various imaging techniques such as Mie-scattering, DBI (diffuse back-illumination), and Schlieren imaging techniques. NI compact RIO system was used to control a test injector. Spray penetration length, length-to-width ratio and number of black pixels were calculated by using MATLAB software to compare spray characteristics of each fuel. Longer spray penetration length and higher length-to-width ratio were observed in propane spray because of flash boiling caused by high saturated vapor pressure. Spray collapse occurred in propane spray due to the high plume-to-plume interaction. Moreover, rapid evaporation occurred in propane spray, so that nozzle tip wetting could not be observed. Rapid evaporation of propane also caused fewer residual droplets compared to n-heptane spray. Therefore, propane is advantageous in reducing the generation of soot emission from large droplets that are not atomized. However, additional evaluation should be conducted considering combustion efficiency and the possibility of deposits by nozzle tip icing during fuel injection.

• 한국항공우주학회지
• /
• 제34권6호
• /
• pp.51-58
• /
• 2006

횡단 유동장내에서 일어나는 분무 현상에 대하여 분사각 변화에 대한 특성과 단일 노즐 형상에서 노즐의 크기와 길이에 대한 분무 특성을 연구하였다. 노즐은 단일 구멍으로 직경이 0.5 ㎜이고 노즐 대 노즐길이의 비(L/D)는 1.0에서 6.0이며 이미지는 고해상 줌 렌즈를 이용한 CCD 카메라를 통해 얻었으며, SMD와 액적의 속도는 PDPA와 상용 프로그램인 Image Express를 사용하였다. 액체 제트의 궤적은 웨버수와 모멘텀비, 노즐형상 변화(L/D)에 영향을 받아 액주가 후방으로 휘어지는 현상이 나타났다. 분사각이 낮을 때(${\theta}$ < $90^{\circ}$)에 노즐 형상보다는 웨버수 증가가 액체 제트의 궤적에 더 크게 영향을 미쳤으며, 분사각이 높을 때(${\theta}$ > $90^{\circ}$)에 노즐 형상 변화에 의한 분열점 변화가 액체 제트의 궤적에 더 크게 영향을 미쳤다.

• Journal of Welding and Joining
• /
• 제25권5호
• /
• pp.64-71
• /
• 2007

The aim of this paper is to investigate the effects of welding parameters on the weld shape in seal-welding of STS304L capsule for manufacturing a radioisotope source which is widely used in nondestructive testing of metal structures using gamma ray. Pulsed gas tungsten arc (Pulsed GTA) welding is performed for thin cross sectional area of the capsule. Seven welding parameters including current waveform parameters and arc length etc. are selected as main process parameters using design of experiment. The weld shape such as bead width, penetration depth, weld area, aspect ratio and area rate is investigated to assess the effects of welding parameters. As results, the combination of pulse duty/welding speed largely affects on bead width, penetration depth, area and aspect ratio. Finally, it is concluded that the key parameters are the combination of pulse duty/welding speed, base current and arc length, and their optimal conditions are 50%/1.77mm/s, 6.4A and 1 mm.

• 한국전산유체공학회:학술대회논문집
• /
• 한국전산유체공학회 2005년도 추계 학술대회논문집
• /
• pp.287-292
• /
• 2005

The flowfields generated by gaseous slot injection into a supersonic flow at a Mach number of 3.75 and a Reynolds number of $2.07{\times}10^7$ are simulated numerically. Fine-scale turbulence effects are represented by a two-equation(k-w SST model) closure model which includes $y^+$ effects on the turbulence model. Grid convergence index(GCI) is also considered to provide a measure of uncertainty of the grid convergence. Comparison is made with experimental data and other turbulence model in term of surface static pressure distributions, the length of the upstream separation region, and the penetration height. Results indicate that the k-w SST model correctly predicts mean surface pressure distribution and upstream separation length. However, it is also observed that the numerical simulation over predicts the pressure spike and penetration height compared with experimental data. All these results are taken within $1\%$ error band of grid convergence.

• 한국작물학회지
• /
• 제36권1호
• /
• pp.12-16
• /
• 1991

보리의 월동전 초형에 따른 농업형질의 차이를 비교하고저 같은 교배조합에서 선발, 고정시킨 계통 및 교배친 10개를 공시하여 분석한 결과는 다음과 같다. 1. 포복형에 비해서 직립형 계통은 출수기 및 성숙기가 빠르고, 간장은 컸으나 $m^2$당 수수, 수량성은 적었다. 또한 천입중, 정입률, 광투과율은 컸다. 2. 출수기는 성숙기, 수량과 정상관, 간장, 천입중, 정입률, 광투과율과 부상관이 있었다. 수량은 광투과율과 부상관이 인정되었다. 3. 월동전에 초형이 포복형이면서, 월동후 생육재생기가 빠르고 식간신장이 빠른 계통을 육성, 선발하는 것이 특히 내한성이 요구되는 지역에서 유리할 것으로 생각된다.

• 대한치과의사협회지
• /
• 제11권4호
• /
• pp.271-276
• /
• 1973

This study is concerned with the effect on Penetration of varing the length of time among the applications of stains, preparations of medicine and radio-active isotope of siver in 120 carious or non carious human teeth with a vital pulp. The study revealed the following conclusions : 1) The stains and preparations penetrated through the dentinal tube and it's seem to be ceased at zone of secondary dentinal area. 2) The stains and preparations did not penetrated in enamel tissues.