• Journal of Advanced Marine Engineering and Technology
• /
• v.40 no.4
• /
• pp.270-274
• /
• 2016

The effect of the rib angle-of-attack on heat transfer in the convergent channel with ${\vee}/{\wedge}$-shaped ribs was examined experimentally. Four differently angled ribs (a = $30^{\circ}$, $45^{\circ}$, $60^{\circ}$, and $90^{\circ}$) were placed to only the one sided wall. The ribbed wall was manufactured with a fixed rib height (e) of 10 mm and rib spacing (p)-to-height (e) ratio of 10. The convergent channel had a length of 1,000 mm and a cross-sectional areas of $100mm{\times}100mm$ at inlet and $50mm{\times}100mm$ at exit. The measurement was conducted for the Reynolds numbers ranging from 22,000 to 75,000. The results show that the Nusselt number is generally higher at higher Reynolds number and that an angle-of-attack of $45^{\circ}$ at the ${\wedge}$-shaped rib produces the greatest Nusselt number.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.40 no.10
• /
• pp.89-94
• /
• 2003

Passive Optical Network(PON) architecture is a very simple. However media access protocol is necessary to the PON because the ONUs should share a channel in the upsteam direction. We propose the design of dynamic bandwidth allocation algorithm for improved bandwidth utilization in the broad bandwidth access network that uses Ethernet PON. The object of our study shall be to decrease a unused remainder bandwidth of granted timeslot for a upstream traffic transmission. We propose that OLT notifies ONU of maximum transmission window during discovery and ONU request a amount under maximum transmission window after it checks a frame length. We confirm that the proposed algorithm shown improving performance from bandwidth utilization and queueing delay point of view through the simulation result.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.26 no.3B
• /
• pp.271-278
• /
• 2006

In design of groyne series, groyne spacing is a important factor and have an effect on not only the characteristics of backward and recirculation flow in groyne zone but also flow field in main channel. It is necessary study about flow pattern of recirculation zone and main channel that is a cause of bad change, local scour and bank erosion by groyne spacing. In this study, flow variation of groyne zone and main chanel for spacing of groynes were analyzed from the experiment results in order to offer a fundamental data that can be used to decide the proper groyne spacing. Experiments were conducted 12 cases for groyne spacing(L) by groyne length(l) rate and the velocity profile was measured using LSPIV and ADV. From the results, two vortex flows developed in recirculation zone for L/l=3~9 and three vortex flows developed over L/l=10. The velocity of backward flow in recirculation zone was decreased up to 20% over L/l=4. The velocity of main channel flow was increased from 1.3 to 2.0 times by groyne spacing and the rate of velocity increased by increasing groyne spacing. The maximum velocity occurred in 0.7~0.8 times of groyne spacing downstream of upper groyne.

• Journal of Advanced Navigation Technology
• /
• v.7 no.2
• /
• pp.128-134
• /
• 2003

In this paper, we investigated the degree of compensation for WDM channel signal distortion due to chromatic dispersion, self phase modulation (SPM) and cross phase modulation (XPM) as a function of transmission length using mid-span spectral inversion (MSSI) compensation method. The considered system is $3{\times}40$ Gbps intensity modulation direct detection (IM/DD) WDM transmission system. This system has highly nonlinear dispersion shifted fiber (HNL-DSF) as a nonlinear medium in optical phase conjugator (OPC). We confirmed that the transmission length is more increased by applying MSSI to distorted signal due to chromatic dispersion, SPM and XPM as dispersion coefficient of fiber becomes higher. And the compensation degree of distorted WDM channels due to chromatic dispersion, SPM and XPM becomes better stable as dispersion coefficient of fiber becomes higher.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2009.06a
• /
• pp.3-4
• /
• 2009

As device process technology advances, effective channel length, the thickness of gate oxide, and supply voltage decreases. This paper describes a novel electrostatic discharge (ESD) protection device which has current feedback for high ESD immunity. A conventional Gate-Grounded NMOS (GGNMOS) transistor has only one ESD current path, which makes, the core circuit be in the safe region, so an GGNMOS transistor has low current immunity compared with our device which has current feedback path. To simulate our device, we use conventional $0.18\;{\mu}m$ technology parameters with a gate oxide thickness of $43\;{\AA}$ and power supply voltage of 1.8 V. Our simulation results indicate that the area of our ESD protection, device can be smaller than a GGNMOS transistor, and ESD immunity is better than a GGNMOS transistor.

• 한국신재생에너지학회:학술대회논문집
• /
• 2011.05a
• /
• pp.98.2-98.2
• /
• 2011

For optimal performance of a proton exchange membrane fuel cell (PEMFC), the membrane electrode assembly (MEA) requires hydration, and the membrane's conductivity depends on water content. A humidifier is required to ensure that the reactant gas, usually hydrogen and air, is hydrated before entering the fuel cell. Dry membrane operation or improper hydration causes performance degradation. Typically, the humidification of a fuel cell is carried out by means of an internal or external humidifier. A membrane humidifier is applied to the external humidification of transportation or residential power generation fuel cell due to its convenience and high performance. In this study, The experiments were constructed with a plate-type membrane humidifier in terms of geometric parameters and operating parameters. The results show that the temperature and pressure, the channel length, the membrane thickness and gas flow rate are critical parameters affecting the performance of the humidifier.

• The Journal of The Korea Institute of Intelligent Transport Systems
• /
• v.8 no.3
• /
• pp.71-82
• /
• 2009

As a solution to spectrum under-utilization problem, Cognitive radio (CR) introduces a dynamic spectrum access technology. In the area, one of the most important problems is how secondary users (SUs) should choose between the available channels, which means how to achieve load balancing between channels. We consider spectrum load balancing problem for CR system in frequency domain and especially in time domain. Our objective is to balance the load among the channels and balance the occupied time length of slots for a fixed channel dynamically in order to obtain a user-optimal solution. In frequency domain, we refer to Dynamic Noncooperative Scheme with Communication (DNCOOPC) used in distributed system and a distributed Dynamic Spectrum Load Balancing algorithm (DSLB) is formed based on DNCOOPC. In time domain, Spectrum Load Balancing method with QoS support is proposed based on Dynamic Feed Back theory and Hash Table (SLBDH). The performance of DSLB and SLBDH are evaluated. In frequency domain, DSLB is more efficient compared with existing Compare_And_Balance (CAB) algorithm and gets more throughput compared with Spectrum Load Balancing (SLB) algorithm. Also, DSLB is a fair scheme for all devices. In time domain, SLBDH is an efficient and precise solution compared with Spectrum Load Smoothing (SLS) method.

• Korean Journal of Optics and Photonics
• /
• v.11 no.5
• /
• pp.335-339
• /
• 2000

A $1.31/1.55\mu\textrm{m}$ coarse WDM opncal dIrectional coupler that conslsls of two idenlical straight channel waveguides in BK7 glass has been fabricated. The separatIOn between two channel waveguides is $8\mu\textrm{m}$ and the wavegu.ide width is $4\mu\textrm{m}$ . Especlally, we assumed that the index profile is Gaussian function and complementary error function in the width direction and depth direction, respectrvely. This directional coupler operating at $1.31/1.55\mu\textrm{m}$ with crosstalk of 18dB is demonstrated and has the 16 mm long length with 12.6 mm coupling region.region.

• Journal of the Korean Society for Precision Engineering
• /
• v.27 no.9
• /
• pp.11-15
• /
• 2010

In this study, to fabricate a low-resistance and high optical transparency electrode film, the following steps were performed: the design and manufacture of electroforming stamp, the fabrication of a thermal roll-imprinted polycarbonate (PC) patterned films, the filled low-resistance Ag paste using doctor blade process on patterned PC films and spin coating by conductive polymers. As a result of PC films imprinted line width of $26.69{\pm}2\;{\mu}m$, channel length of $247.57{\pm}2\;{\mu}m$, and pattern depth of $7.54{\pm}0.2\;{\mu}m$. Ag paste to fill part of the patterned film with conductive polymer coating and then the following parameters were obtained: a sheet resistance of $11.1\;{\Omega}/sq$ optical transparency values at a wavelength of 550 nm was 80.31 %.

• Journal of Sensor Science and Technology
• /
• v.31 no.5
• /
• pp.324-329
• /
• 2022

This paper proposes a shift-register-based multichannel ultrasonic focusing delay control method using a complex programmable logic device (CPLD) for a high resolution of ultrasonic focusing system. The proposed method can achieve the ultrasonic focusing through the delay control of driving signals of each ultrasonic transducer of an ultrasonic array. The delay of the driving signals of all ultrasonic channels can be controlled by setting the shift register in the CPLD. The experiment verified that the frequency of the clock used for the delay control increased, the error of the focusing point decreased, and the diameter of the focusing point decreased as the length of the shift register in the proposed method. The proposed method used only one CPLD for ultrasonic focusing and did not require to use complex hardware circuits. Therefore, the resources required for the design of an ultrasonic focusing system could be reduced. The proposed method can be applied to the fields of human computer interaction (HCI), virtual reality (VR) and augmented reality (AR).