• Journal of Biosystems Engineering
• /
• v.4 no.2
• /
• pp.64-64
• /
• 1979

Low-temperature drying systems have been extensively used for drying cereal grain such as shelled corn and wheat. Since the 1973 energy crisis, many researches have been conducted to apply solar energy as supplemental heat to natural air drying systems. However, little research on rough rice drying has been done in this area, especially very little in Korea. In designing a solar drying system, quality loss, airflow requirements, temperature rise of drying air, fan power and energy requirements should be throughly studied. The factors affecting solar drying systems are airflow rate, initial moisture content, the amount of heat added to drying air, fan operation method and the weather conditions. The major objectives of this study were to analyze the effects of the performance factors and determine design parameters such as airflow requirements, optimum bed depth, optimum temperature rise of drying air, fan operation method and collector size. Three hourly observations based on the 4-year weather data in Chuncheon area were used to simulate rough rice drying. The results can be summarized as follows: 1. The results of the statistical analysis indicated that the experimental and predicted values of the temperature rise of the air passing through the collector agreed well.2. Equilibrium moisture content was affected a little by airflow rate, but affected mainly by the amount of heat added, to drying air. Equilibrium moisture content ranged from 12.2 to 13.2 percent wet basis for the continuous fan operation, from 10.4 to 11.7 percent wet basis for the intermittent fan operation respectively, in range of 1. 6 to 5. 9 degrees Centigrade average temperature rise of drying air.3. Average moisture content when top layer was dried to 15 percent wet basis ranged from 13.1 to 13.9 percent wet basis for the continuous fan operation, from 11.9 to 13.4 percent wet basis for the intermittent fan operation respectively, in the range of 1.6 to 5.9 degrees Centigrade average temperature rise of drying air and 18 to 24 percent wet basis initial moisture content. The results indicated that grain was overdried with the intermittent fan operation in any range of temperature rise of drying air. Therefore, the continuous fan operation is usually more effective than the intermittent fan operation considering the overdrying.4. For the continuous fan operation, the average temperature rise of drying air may be limited to 2.2 to 3. 3 degrees Centigrade considering safe storage moisture level of 13.5 to 14 perceut wet basis.5. Required drying time decrease ranged from 40 to 50 percent each time the airflow rate was doubled and from 3.9 to 4.3 percent approximately for each one degrees Centigrade in average temperature rise of drying air regardless of the fan operation methods. Therefore, the average temperature rise of drying air had a little effect on required drying time.6. Required drying time increase ranged from 18 to 30 percent approximately for each 2 percent increase in initial moisture content regardless of the fan operation methods, in the range of 18 to 24 percent moisture.7. The intermittent fan operation showed about 36 to 42 percent decrease in required drying time as compared with the continuous fan operation.8. Drymatter loss decrease ranged from 34 to 46 percent each time the airflow rate was doubled and from 2 to 3 percent approximately for each one degrees Centigrade in average temperature rise of drying air, regardless of the fan operation methods. Therefore, the average temperature rise of drying air had a little effect on drymatter loss. 9. Drymatter loss increase ranged from 50 to 78 percent approximately for each 2 percent increase in initial moisture content, in the range of 18 to 24 percent moisture. 10. The intermittent fan operation: showed about 40 to 50 percent increase in drymatter loss as compared with the continuous fan operation and the increasing rate was higher at high level of initial moisture and average temperature rise.11. Year-to-year weather conditions had a little effect on required drying time and drymatter loss.12. The equations for estimating time required to dry top layer to 16 and 1536 wet basis and drymatter loss were derived as functions of the performance factors. by the least square method.13. Minimum airflow rates based on 0.5 percent drymatter loss were estimated.Minimum airflow rates for the intermittent fan operation were approximately 1.5 to 1.8 times as much as compared with the continuous fan operation, but a few differences among year-to-year.14. Required fan horsepower and energy for the intermittent fan operation were3. 7 and 1. 5 times respectively as much as compared with the continuous fan operation.15. The continuous fan operation may be more effective than the intermittent fan operation considering overdrying, fan horsepower requirements, and energy use.16. A method for estimating the required collection area of flat-plate solar collector using average temperature rise and airflow rate was presented.

• Journal of Korean Society of Coastal and Ocean Engineers
• /
• v.31 no.3
• /
• pp.158-169
• /
• 2019

A probabilistic model that can predict the residual useful lifetime of structure is formulated by using the gamma process which is one of the stochastic processes. The formulated stochastic model can take into account both the sampling uncertainty associated with damages measured up to now and the temporal uncertainty of cumulative damage over time. A method estimating several parameters of stochastic model is additionally proposed by introducing of the least square method and the method of moments, so that the age of a structure, the operational environment, and the evolution of damage with time can be considered. Some features related to the residual useful lifetime are firstly investigated into through the sensitivity analysis on parameters under a simple setting of single damage data measured at the current age. The stochastic model are then applied to the rubble-mound breakwater straightforwardly. The parameters of gamma process can be estimated for several experimental data on the damage processes of armor rocks of rubble-mound breakwater. The expected damage levels over time, which are numerically simulated with the estimated parameters, are in very good agreement with those from the flume testing. It has been found from various numerical calculations that the probabilities exceeding the failure limit are converged to the constraint that the model must be satisfied after lasting for a long time from now. Meanwhile, the expected residual useful lifetimes evaluated from the failure probabilities are seen to be different with respect to the behavior of damage history. As the coefficient of variation of cumulative damage is becoming large, in particular, it has been shown that the expected residual useful lifetimes have significant discrepancies from those of the deterministic regression model. This is mainly due to the effect of sampling and temporal uncertainties associated with damage, by which the first time to failure tends to be widely distributed. Therefore, the stochastic model presented in this paper for predicting the residual useful lifetime of structure can properly implement the probabilistic assessment on current damage state of structure as well as take account of the temporal uncertainty of future cumulative damage.

• Journal of Korean Society of Coastal and Ocean Engineers
• /
• v.32 no.3
• /
• pp.147-160
• /
• 2020

A stochastic probabilistic model for harbor structures such as rubble-mound breakwater has been formulated by using the generalized Wiener process considering the nonlinearity of damage drift and its nonlinear uncertainty, by which the damage path with real-time can be tracked, the residual useful lifetime at some age can also be analyzed properly. The formulated stochastic model can easily calculate the probability of failure with the passage of time through the probability density function of cumulative damage. In particular, the probability density functions of residual useful lifetime of the existing harbor structures can be derived, which can take into account the current age, its present damage state and the future damage process to be occurred. By using the maximum likelihood method and the least square method together, the involved parameters in the stochastic model can be estimated. In the calibration of the stochastic model presented in this paper, the present results are very well similar with the results of MCS about tracking of the damage paths as well as evaluating of the density functions of the cumulative damage and the residual useful lifetime. MTTF and MRL are also evaluated exactly. Meanwhile, the stochastic probabilistic model has been applied to the rubble-mound breakwater. The related parameters can be estimated by using the experimental data of the cumulative damages of armor units measured as a function of time. The theoretical results about the probability density function of cumulative damage and the probability of failure are very well agreed with MCS results such that the density functions of the cumulative damage tend to move to rightward and the amounts of its uncertainty are increased as the elapsed time goes on. Thus, the probabilities of failure with the elapsed time are also increased sharply. Finally, the behaviors of residual useful lifetime have been investigated with the elapsed age. It is concluded for rubble-mound breakwaters that the probability density functions of residual useful lifetime tends to have a longer tail in the right side rather than the left side because of the gradual increases of cumulative damage of armor units. Therefore, its MRLs are sharply decreased after some age. In this paper, the special attentions are paid to the relationship of MTTF and MRL and the elapsed age of the existing structure. In spite of that the sum of the elapsed age and MRL must be equal to MTTF deterministically, the large difference has been shown as the elapsed age is increased which is due to the uncertainty of cumulative damage to be occurred in the future.

• The Korean Journal of Nuclear Medicine
• /
• v.32 no.5
• /
• pp.414-424
• /
• 1998

Purpose: Cross-modality coregistration of positron emission tomography (PET) and magnetic resonance imaging (MR) could enhance the clinical information. In this study we propose a refined technique to improve the robustness of registration, and to implement more realistic visualization of the coregistered images. Materials and Methods: Using the sinogram of PET emission scan, we extracted the robust head boundary and used boundary-enhanced PET to coregister PET with MR. The pixels having 10% of maximum pixel value were considered as the boundary of sinogram. Boundary pixel values were exchanged with maximum value of sinogram. One hundred eighty boundary points were extracted at intervals of about 2 degree using simple threshold method from each slice of MR images. Best affined transformation between the two point sets was performed using least square fitting which should minimize the sum of Euclidean distance between the point sets. We reduced calculation time using pre-defined distance map. Finally we developed an automatic coregistration program using this boundary detection and surface matching technique. We designed a new weighted normalization technique to display the coregistered PET and MR images simultaneously. Results: Using our newly developed method, robust extraction of head boundary was possible and spatial registration was successfully performed. Mean displacement error was less than 2.0 mm. In visualization of coregistered images using weighted normalization method, structures shown in MR image could be realistically represented. Conclusion: Our refined technique could practically enhance the performance of automated three dimensional coregistration.

• Analytical Science and Technology
• /
• v.25 no.2
• /
• pp.121-126
• /
• 2012

It is essential to evaluate the quality of Hanji record paper without damaging the record paper by previous destructive methods. The samples were Hanji record paper produced in the 1900s. Near-infrared (NIR) spectrometer was used as a non destructive method for evaluating the quality of record papers. Fourier transform (FT) spectrometer was used with 12,500 to 4,000 $cm^{-1}$ wavenumber range for quantitative analysis and it has high accuracy and good signal-to-noise ratio. The acidity and moisture content of Hanji record paper were measured by integrating sphere as diffuse reflectance type. The acidity (pH) of chemical factors as a quality evaluated factor of Hanji was correlated to NIR spectrum. The NIR spectrum was pretreated to obtain the coefficients of optimum correlation. Multiplicative scatter correction (MSC) and First derivative of Savitzky-Golay were used as pretreated methods. The coefficients of optimum correlation were calculated by PLSR (partial least square regression). The correlation coefficients ($R^2$) of acidity had 0.92 on NIR spectra without pretreatment. Also the standard error of prediction (SEP) of pH was 0.24. And then the NIR spectra with pretreatment would have better correlation coefficient ($R^2$ = 0.98) and 0.19 as SEP on pH. For moisture contents, the linearity correlation without pretreatment was higher than the case with pretreatment (MSC, $1^{st}$ derivative). As the best result, the $R^2$ was 0.99 and SEP was 0.45. This indicates that it is highly proper to evaluate the quality of Hanji record papers speedily with integrated sphere and FT NIR analyzer as a non-destructive method.

• The Journal of the Korean Society for Microbiology
• /
• v.15 no.1
• /
• pp.19-32
• /
• 1980

Besides the benefits of antimicrobial agents in the control of various infectious diseases, widespread and prolonged use of particular antimicrobial agents has brought about the increase of drug-resistant strains in a community and the profound changes in the pattern of infectious diseases. In Korea, there are some remote villages where no clinics and drug stores are available and the residents in those areas are assumed to have fewer chances to contact with antimicrobial agents. In the present study, the differences in susceptibilities to 14 antimicrobial agents between the isolates from rural areas(R) and Seoul National University Hospital(SNUH, H) were studied. The isolates and their numbers were Staphylococcus aureus, R;55, H;68), Enterococci(R;28, H;30), Escherichia coli(R;40, H;40), Enterobacter aerogenes(R;25, H;21) and Klebsiella pneunoniae(R;58, H;67). Minimal inhibitory concentrations(MIC's) of penicillin, ampicillin, carbenicillin, cephalexin, tetracycline, oxytetracyline, doxycycline, minocycline, gentamicin, kanamycin, streptomycin, erythromycin, troleandomycin and co-trimoxazole were determined by agar dilution method. I. Comparison of MIC's and resistant strain proportions between isolates from SNUH and rural areas. MIC's and/or resistant strain proportions of the isolates from SNUH were significantly higher than those of the isolates from rural areas in the cases of 1. S. aureus to doxycycline, streptomycin and kanamycin. 2. E. coli to penicillin, ampicillin, carbenicillin, tetracycline, oxytetracycline, doxycycline, minocycline, streptomycin, kanamycin, erythromycin and co-trimoxazole. 3. E. aerogences to carbenicillin, tetracycline, oxytetracycline, doxycycline, minocycline, streptomycin, kanamycin, genaamicin and co-trimoxazole. 4. K pneunoniae to penicillin, ampicillin, tetracycline, oxytetracycline, doxycycline, monocycline, streptomycin, kanamycine, gentamicin and co-trimoxazole. However, the mean MIC and resistant strain proportion of S. aureus to tetracycline were higher in isolates from rural areas than in those from SNUH and Enterococci showed no differences in susceptibilities to the antimicrobial agents between isolates from rural areas and from SNUH. Therefore, in general, differenes in susceptibility to these antimicrobial agents between the isolates from rural areas and SNUH were remarkably greater and broader in gram negative enteric bacteria. II. Multiple drug resistance pattern. Patterns and incidences of multiple drug resistance were studied with penicillin, ampicillin, tetracycline, cephalexin, gentamicin, streptomcin, kanamycin and co-trimoxazole in Enterococci, E. coli, E. aeroges and K. pneumoniae. There appeared significant differences in the incidence of multiply drug-resistant strains and multiple drug resistance patterns between the isolates from SNUH and rural areas in Enterococci, E. coli, E. aerogenes and K. pneumoniae. However, there was no difference in the incidence of multiply drug-resistant strains between isolates of S. aureus from SNUH and rural areas but the pattern of multiple resistance of the SNUH strains of S. aureus was diverse, while that of the rural strains was predominantly confined to penicillin-tetracycline combination. The incidence of multigly drug-resistant strains and diversity of their patterns were the highest in E. coli strains isolated from SNUH and there were no multiply drug resistant strrains in Enterococci and K. pneumoniae strains isolated from rural areas. The number of drug-resistance determinants was also different between the isolates from rural areas and SNUH. Most of the multiply drug-resistant strains of E. coli, E. aerogenes and K. pneumoniae isolated from SNUH were resistant to more than 3 kinds of antimicrobial agents, most frequently to ampicillin, tetracycline and streptomycin, while multiply drug-resistant strains from rural areas were resistant to 2 kinds of antimicrobial agents among ampicillin, tetracycline and streptomycin. With drug-resistant E. coli strains, resistance to tetracycline which was used most widely since 1951 was most frequently involved as a part of mutliple drug-resistance, followed by resistance to ampicillin and streptomycin. This strongly suggests that emergence of drug-restant strains in a community is directly dependent on the selective pressure exerted by the antimicrobial agent used. III. Cross resistance. Cross resistance of bacteria was studied among tetracycline penicillin, aminoglycoside and macrolide derivatives by analyzing correlation coefficients of sucseptibilities using the least square method. In this study, there were high correlations among the susceptibilities to related derivatives. It appears that the relatively low correlations in susceptibilities present in some cases are due to intrinsic resistance of E. aerogenes to penicillin, Enterococci to aminoglycoside and E. coli E. aerogenes and K. pneumoniae to macrolide derivatives.

• Journal of Animal Science and Technology
• /
• v.50 no.1
• /
• pp.33-44
• /
• 2008

The purpose of this study was to estimate the genetic parameters and trend of Landrace and Yorkshire pigs, which were raised on private farms from 1999 to 2005 and tested for their reproductive performance by the Korea Animal Improvement Association. Prior to analysis, records without pedigree or having value with larger than±3×standard deviation for the Total number of born were excluded. The effects of breed and environmental factors were estimated with least square method(Harvey, 1979), and estimation of breeding values and genetic parameters were performed on the data of 1’st litter only with GIBBSF90(Misztal, 2001) which was programmed according to Gibbs Sampling method based on Bayesian Inference by Gianola and Fernando(1986), Jensen(1994) and others. Gibbs sampling was performed 50,000 times for each parameter, and the first 5000 samples were regarded as those in burn-in period and thus, excluded for post hoc analysis. Total number of born and total number of accident were statistically significant(p<0.01) for the breed, farrowing year, farrowing season and parity effects, and the number born alive at birth was statistically significantp<(0.01) for the breed, farrowing year, farrowing season and parity effects. No particular trend was observed in the genetic and phenotypic improvement of the total number of born and number born alive at birth before 2001, when the piglet registration system started, but the tendencies of increasing for the total number of born and number born alive and decreasing for the total number of accident were observed since 2001. Somewhat higher heritability estimates of our study seems to be attributed to the situations that first parity records with poor farrowing performances were used in the analyses and it was impossible to obtain accurate reproductive performance due to the absence of criteria for record keeping at the level of individual farms.

• Food Science and Preservation
• /
• v.19 no.1
• /
• pp.95-103
• /
• 2012

The objective of this study was to develop models for the predict of the milk properties (fat, protein, SNF, lactose, MUN) of unhomogenized milk using the visible and near-infrared (NIR) spectroscopic technique. A total of 180 milk samples were collected from dairy farms. To determine optimal measurement temperature, the temperatures of the milk samples were kept at three levels ($5^{\circ}C$, $20^{\circ}C$, and $40^{\circ}C$). A spectrophotometer was used to measure the reflectance spectra of the milk samples. Multilinear-regression (MLR) models with stepwise method were developed for the selection of the optimal wavelength. The preprocessing methods were used to minimize the spectroscopic noise, and the partial-least-square (PLS) models were developed to prediction of the milk properties of the unhomogenized milk. The PLS results showed that there was a good correlation between the predicted and measured milk properties of the samples at $40^{\circ}C$ and at 400~2,500 nm. The optimal-wavelength range of fat and protein were 1,600~1,800 nm, and normalization improved the prediction performance. The SNF and lactose were optimized at 1,600~1,900 nm, and the MUN at 600~800 nm. The best preprocessing method for SNF, lactose, and MUN turned out to be smoothing, MSC, and second derivative. The Correlation coefficients between the predicted and measured fat, protein, SNF, lactose, and MUN were 0.98, 0.90, 0.82, 0.75, and 0.61, respectively. The study results indicate that the models can be used to assess milk quality.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2000.11a
• /
• pp.3-4
• /
• 2000

Many researchers are interested in the synthesis and characterization of carbon nitride and diamond-like carbon (DLq because they show excellent mechanical properties such as low friction and high wear resistance and excellent electrical properties such as controllable electical resistivity and good field electron emission. We have deposited amorphous carbon nitride (a-C:N) thin films and DLC thin films by shielded arc ion plating (SAIP) and evaluated the structural and tribological properties. The application of appropriate negative bias on substrates is effective to increase the film hardness and wear resistance. This paper reports on the deposition and tribological OLC films in relation to the substrate bias voltage (Vs). films are compared with those of the OLC films. A high purity sintered graphite target was mounted on a cathode as a carbon source. Nitrogen or argon was introduced into a deposition chamber through each mass flow controller. After the initiation of an arc plasma at 60 A and 1 Pa, the target surface was heated and evaporated by the plasma. Carbon atoms and clusters evaporated from the target were ionized partially and reacted with activated nitrogen species, and a carbon nitride film was deposited onto a Si (100) substrate when we used nitrogen as a reactant gas. The surface of the growing film also reacted with activated nitrogen species. Carbon macropartic1es (0.1 -100 maicro-m) evaporated from the target at the same time were not ionized and did not react fully with nitrogen species. These macroparticles interfered with the formation of the carbon nitride film. Therefore we set a shielding plate made of stainless steel between the target and the substrate to trap the macropartic1es. This shielding method is very effective to prepare smooth a-CN films. We, therefore, call this method "shielded arc ion plating (SAIP)". For the deposition of DLC films we used argon instead of nitrogen. Films of about 150 nm in thickness were deposited onto Si substrates. Their structures, chemical compositions and chemical bonding states were analyzed by using X-ray diffraction, Raman spectroscopy, X-ray photoelectron spectroscopy and infrared spectroscopy. Hardness of the films was measured with a nanointender interfaced with an atomic force microscope (AFM). A Berkovich-type diamond tip whose radius was less than 100 nm was used for the measurement. A force-displacement curve of each film was measured at a peak load force of 250 maicro-N. Load, hold and unload times for each indentation were 2.5, 0 and 2.5 s, respectively. Hardness of each film was determined from five force-displacement curves. Wear resistance of the films was analyzed as follows. First, each film surface was scanned with the diamond tip at a constant load force of 20 maicro-N. The tip scanning was repeated 30 times in a 1 urn-square region with 512 lines at a scanning rate of 2 um/ s. After this tip-scanning, the film surface was observed in the AFM mode at a constant force of 5 maicro-N with the same Berkovich-type tip. The hardness of a-CN films was less dependent on Vs. The hardness of the film deposited at Vs=O V in a nitrogen plasma was about 10 GPa and almost similar to that of Si. It slightly increased to 12 - 15 GPa when a bias voltage of -100 - -500 V was applied to the substrate with showing its maximum at Vs=-300 V. The film deposited at Vs=O V was least wear resistant which was consistent with its lowest hardness. The biased films became more wear resistant. Particularly the film deposited at Vs=-300 V showed remarkable wear resistance. Its wear depth was too shallow to be measured with AFM. On the other hand, the DLC film, deposited at Vs=-l00 V in an argon plasma, whose hardness was 35 GPa was obviously worn under the same wear test conditions. The a-C:N films show higher wear resistance than DLC films and are useful for wear resistant coatings on various mechanical and electronic parts.nic parts.

• KOREAN JOURNAL OF CROP SCIENCE
• /
• v.41 no.4
• /
• pp.420-428
• /
• 1996

This study was conducted to investigate the response of growth and yield of rice under five different cultural methods, machine transplanting(MTNT), puddled drill seeding (PDSNT), drill seeding on soil surface (DSNT) , broadcasting on soil surface (BSNT) under no-tillage paddy condition and conventional machine transplanting(MTT) in Jeonbuk series(siltyloam soil) from 1993 to 1995. Soil hardness was higher in no-tillage soil and increased with highly difference between tillaged and no-tillage soil with deeper soil depth. Bulk density was heavier in no-tillage soil and porosity was higher in tilled soil than that of the control. The rate of effective tiller was higher in MTT, following MTNT, PDSNT, DSNT and BSNT. Weed occurrence was more serious in no-tillage soil, than that of tillaged soil. The rate of lower internode length was lower in DSNT and BSNT and was similar with MTT in PDSNT and MTNT. Height of center gravity in terms of lodging tolerance was lower in direct seeding than in machine transplanting. Depth of buried culm was shorter in no-tillage soil, especially in DSNT and BSNT. Total amount of root was higher in MTT, following MTNT, PDSNT, BSNT and BSNT and the distribution rate of root in shallower soil layer was higher in no-tillage soil, especially in BSNT and DSNT. Field lodging occured highly in BSNT, following DSNA, PDSNT and MTNT with high lodging scale in DSNT and BSNT. Panicle number per unit land square meter was the highest in MTT and the least in BSNT. Ripened grain ratio was low in BSNT and DSNT due to heavy lodging. Yield of milled rice was 93% in PDSNT, 87% in DSNT, 81% in BSNT and 96% in MTNT, compared with 534kg /10a in MTT.