• Journal of Korean Society of Disaster and Security
• /
• v.11 no.2
• /
• pp.53-60
• /
• 2018

To diagnosis the local damages of the steel plates, magnetic flux leakage (MFL) method that is known as a adaptable non-destructive evaluation (NDE) method for continuum ferromagnetic members was applied in this study. To analysis the sensitivity according to thickness of steel plate in MFL method based damage diagnosis, several steel plate specimens that have different thickness were prepared and three depths of artificial damage were formed to the each specimens. To measured the MFL signals, a MFL sensor head that have a constant magnetization intensity were fabricated using a hall sensor and a magnetization yoke using permanent magnets. The magnetic flux signals obtained by using MFL sensor head were improved through a series of signal processing methods. The capability of local damage detection was verified from the measured MFL signals from each damage points. And, the peak to peak values (P-P value) extracted from the detected MFL signals from each thickness specimen were compared each other to analysis the MFL based local damage detection sensitivity according to the thickness of steel plate.

• Journal of the Korean Institute of Gas
• /
• v.15 no.6
• /
• pp.28-33
• /
• 2011

The purpose of this paper analyzes and studies to improve the failure cases on the computer that one of electronic control elements for engine in liquified petroleum gas vehicle. The first case, it certified the non-starting phenomenon of engine that it's electronic control unit didn't control the fuel for idle speed actuator because of no given action signal in slow-cut solenoid valve. The second case, it knew the bad condition phenomenon of engine and back-fire by the wire melting of ignition coil and firing of transistor being inside ECU. The third case, it certified the action stoping phenomenon of engine and malfunctioning signal for engine ECU because of leakage of current and an excess current by moisture inflowing inside ECU curcuit plate. Therefore, it is thought that will elevate the durability and reliability of engine computer throughout procure of quality.

• The Journal of The Korea Institute of Intelligent Transport Systems
• /
• v.9 no.2
• /
• pp.51-59
• /
• 2010

In this paper, we propose an inverted type asymmetric Doherty amplifier with optimized efficiency characteristic in wanted output power back-off (OPBO) range according to peak to average power ratio of input signal In order to obtain optimized efficiency of the asymmetric Doherty amplifier in wanted OPBO, peak power ratio between main amplifier and peaking amplifier was determined and then impedance of 90 degrees impedance transformer was obtained by peak power ratio. The offset line length and peak dividing ratio of the asymmetric Doherty amplifier were also calculated. From the measurement results, the proposed amplifier has achieved 40 % drain efficiency and -35 dBc adjacent channel leakage ratio at the average output power of 48.7 dBm for CDMA 2000 1x 3-FA test signal.

• Korean Journal of Optics and Photonics
• /
• v.8 no.4
• /
• pp.340-344
• /
• 1997

We proposed and demonstrated a tunable wavelength optical add/drop multiplexer(OADM) employing piezoactuated fiber grating pairs and polarization beam splitters. We used piezostack act as a fiber stretcher, using the fact that the resonant wavelength of the grating can be controlled by the axial strain along the fiber grating. The polarization controlled configuration showed high stability because the reflected signals from the two identical gratings are dropped or added not by interference but by polarizations of the beams. We could add and drop not noly 1549.3nm signal channel(original gratings), but also 1550.1nm(tuned gratings) with PZT actuators and in both cases, we found that the rejection of adjacent channels was more than -26dB, and signal leakage at the gratings was less than -34dB.

• Journal of the Korean Recycled Construction Resources Institute
• /
• v.5 no.2
• /
• pp.177-184
• /
• 2017

Many ground subsidence accidents have happened in Korea. The accident was caused by the subsidence and leakage of the deteriorated sewage pipe. This study aims to establish the empirical data of the ground penetration radar(GPR) detection for ground subsidence. A test bed was also manufactured for the same purpose. The GPR detection variables are embedment depth and horizontal distance of embedded cast iron pipe and expanded polystyrene(EPS). From the detection results, the EPS embedded by a depth of 1.5m was difficult for detection. The EPS closely embedded to the cast iron pipe within a 0.5m distance had a very strong cast iron pipe signal. Therefore, the detection was impossible. This study developed an image processing program, called the GPR image processing program(GPRiPP), to process the GPR detection results. Its major function is the gain function, which amplifies the wiggle wave signal. Compared to the existing programs, the GPRiPP is capable of showing a similar image processing performance.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.16 no.2 s.93
• /
• pp.134-138
• /
• 2005

In this paper, we have developed a new type of the microwave phase conjugator for the active retrodirective antenna array. The circuit topology is consisted of a 2-port structure to avoid the complexity of LO and RF signal combination and matching, using the cascade connection of two single-ended mixers. The operating frequencies are 4.0 GHz, 2.01 GHz and 1.99 GHz for LO, RF, and IF, respectively. Conversion loss is measured to be -7 dB and 1-dB compression point 15 dBm with the LO power of 9 dBm. For the most important parameter, the isolation between RE leakage and IF signal is as high as 25 dB.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.21 no.5
• /
• pp.556-560
• /
• 2001

Remote field eddy current testing (RFECT) with through-wall transmission characteristic is being applied to pipes ranging from small tubes of heat exchanger to natural gas supply pipelines. Cast iron pipes with nominal diameter of 100mm are used primarily as the waterline pipes. The leakage of water occurs due to defects in the pipes caused by vibration of automobiles and corrosion. But, the use of direct inspection methods such as insertion of inspection equipment inside the pipelines has been limited due to its lack of economical efficiency. Economical development of inspection equipments is possible since RFECT method can be easily employed for system integration and quantitative evaluation of both inside and outside defects. In this study, the development of underground pipeline inspection system was tarried out by using RFECT method in consideration of the characteristics of waterline network. This paper specifically describes the design and production of RFECT pipeline inspection pig using centralizer mechanism, development of remote field eddy current signal acquisition and processing software, and review of RFECT system operation procedures.

• Journal of Advanced Navigation Technology
• /
• v.18 no.4
• /
• pp.341-346
• /
• 2014

This paper has presented the design and fabrication of phase correlator for wideband digital frequency discriminator (DFD) operating over the 6.0 to 18.0 GHz frequency range. Fabricated DFD phase correlator has been measured I or Q output signal, and analyzed frequency discrimination error. The operation of the proposed mixer type correlator has been analyzed by deriving some analytic equations. To design the phase correlator, this paper has modeled and simulated IQ mixer and 8-way power divider by using RF simulation tool. Designed phase correlator has fabricated and measured. The phase error and frequency discrimination error have been presented using by measured I and Q output signal. Over the 6.0~18.0 GHz range, the root mean square(RMS) phase error is $4.81^{\circ}$, RMS and frequency discrimination error is 1.49 MHz, RMS.

• Journal of the Korean Society for Railway
• /
• v.15 no.2
• /
• pp.122-128
• /
• 2012

Considering structure of depot, it is impossible to install the track circuit systems due to iron-beam. Because rails and earth are connected by the iron-beam, there is much leakage current. So, it is hard to apply the track circuit systems. Thus, when trains go to the depot, sign which indicates existence of trains is used manually. In case of wrong sign, accidents occur such as train crash, derailment etc. Currently, location of trains has been found by using optical sensor in the depot to prevent the accidents. However, it costs a great deal to install and maintain the optical sensor. Therefore, this method is hardly used in train operation institutes. In this paper, virtual track circuit systems are introduced by using software program in the depot. Also, algorithm of the virtual track circuit systems is proposed. In case that signal is handled to the depot which is occupied by the train, safety is ensured by indicating sign which means existence of trains and stop signal. Also, proper fault tolerance techniques are proposed to the software by analyzing reliability and availability.

• Journal of electromagnetic engineering and science
• /
• v.14 no.4
• /
• pp.393-398
• /
• 2014

A highly efficient dual-mode linear CMOS stacked-FET power amplifier (PA) is implemented for 3G UMTS and 4G LTE handset applications. High efficiency is achieved at a backed-off output power ($P_{out}$) below 12 dBm by employing an active-bypass amplifier, which consumes very low quiescent current and has high load-impedance. The output paths between high- and low-power modes of the PA are effectively isolated by using a bypass switch, thus no RF performance degradation occurs at high-power mode operation. The fabricated 900 MHz CMOS PA using a silicon-on-insulator (SOI) CMOS process operates with an idle current of 5.5 mA and shows power-added efficiency (PAE) of 20.5%/43.5% at $P_{out}$ = 12.4 / 28.2 dBm while maintaining an adjacent channel leakage ratio (ACLR) better than -39 dBc, using the 3GPP uplink W-CDMA signal. The PA also exhibits PAE of 35.1% and $ACLR_{E-UTRA}$ of -33 dBc at $P_{out}$ = 26.5 dBm, using the 20 MHz bandwidth 16-QAM LTE signal.