• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2003년도 추계학술대회
• /
• pp.845-850
• /
• 2003

Unsteady nature of a tip leakage vortex in an axial flow fan operating at a design and off-design operating conditions has been investigated by measuring the velocity fluctuation in a blade passage with a rotating hotwire probe sensor. Two hot-wire probe sensors rotating with the fan rotor were also introduced to obtain the cross-correlation coefficient between the two sensors located in the vortical flow as well as the fluctuating velocity. The results show that the vortical flow structure near the rotor tip can be clearly observed at the quasi-orthogonal planes to a tip leakage vortex. The leakage vortex is enlarged as the flow rate is decreased, thus resulting in the high blockage to main flow. The spectral peaks due to the fluctuating velocity near the rotor tip are mainly observed in the reverse flow region at higher flow rates than the peak pressure operating condition. However, no peak frequency presents near the rotor tip for near stall condition.

• 한국유체기계학회 논문집
• /
• 제7권1호
• /
• pp.36-44
• /
• 2004

Three-dimensional vortical flow and separated flow topology near the casing wall in an axial flow fan having two different tip clearances have been investigated by a Reynolds-averaged Navier-Stokes (RANS) flow simulation. The simulation shows that the tip leakage vortex formed close to the leading edge of the blade tip on suction side grows in the streamwise direction. On the casing wall, a separation line is formed upstream of the leakage vortex center due to the interference between the leakage vortex and main flow. The reverse flow is observed between the separation line and the attachment line generated downstream of the trailing edge, and increased with enlarging tip clearance. The patterns of a leakage velocity vector including a leakage flow rate are also analyzed according to two tip clearances. It is noted that the understanding of the distribution of a limiting streamline on the casing wall is very important to grasp the characteristics of the vortical flow in the axial flow fan.

• Tribology and Lubricants
• /
• 제24권6호
• /
• pp.349-354
• /
• 2008

An inter-propellant seal (IPS) for high thrust turbopump is designed. With given operating conditions and requirements, the inter-propellant seal is designed to satisfy the leakage characteristics which is less than 0.1% of normal flow rate of pumps. A numerical analysis is developed to predict the leakage flow rate. The results show that the maximum leakage of LOX and kerosene are less than 0.1% of normal flow rate of pumps, respectively. Based on the numerical analysis results, the detail of IPS is performed. Finally a prototype of IPS is manufactured to perform sets of performance tests in the near future.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2004년도 추계학술대회
• /
• pp.1383-1388
• /
• 2004

The flow characteristics in the blade passage of a low speed axial flow fan have been investigated by experimental analysis using a rotating hot-wire sensor for design and off-design operating conditions. The results show that the tip leakage vortex is moved upstream when flow rate is decreased, thus disturbing the formation of wake flow near the rotor tip. The tip leakage vortex interfaces with blade pressure surface, and results in high velocity fluctuation near the pressure surface. From the relative velocity distributions near the rotor tip, large axial velocity decay is observed at near stall condition, which results in large blockage compared to that at the design condition. Througout the flow measurements using a quasi-orthogonal measuring points to the tip leakage vortex, it is noted that the radial position of the tip leakage vortex is distributed between 94 and 96 percent span for all flow conditions. High spectrum density due to the large fluctuation of the tip leakage vortex is observed near the blade suction surface below the frequency of 1000 Hz at near stall condition.

• 한국수소및신에너지학회논문집
• /
• 제23권4호
• /
• pp.316-322
• /
• 2012

A fuel cell vehicle has the hydrogen detection sensors for checking the hydrogen leakage because it use hydrogen for its fuel and can't use a odorant to protect the fuel cell stack. To verify the hydrogen safety of leakage we select the high possible leak points of fittings in hydrogen storage system and test the leaking behavior at them. The hydrogen leakage flow rate is 10, 40, 118 NL/min and the criterion for maximum hydrogen leakage is based on allowing an equivalent release of combustion energy as permitted by gasoline vehicles in FMVSS301. There are total 18EA hydrogen leakage detection sensors installed in test system. we acquire the hydrogen leakage detection time and determine the ranking. Hydrogen leakage detection time decrease when hydrogen leakage flow rate increase. The minimum hydrogen leakage detection time is about 3 seconds when the flow rate is 118NL/min. In this study, we optimize hydrogen sensor position in fuel cell vehicle and verify the hydrogen leakage safety because there is no inflow inside the vehicle.

• 대한기계학회논문집B
• /
• 제36권1호
• /
• pp.37-45
• /
• 2012

제습로터에서 발생하는 공기누설은 로터와 브러쉬 형태의 누설방지모 틈새의 양단 사이 차압에 의해 발생하는 압력누설이 지배적이며, 실험을 통해 압력누설특성을 파악하였다. 그 결과로, 압력누설량을 로터와 누설방지모의 틈새면적과 차압의 함수로 나타내었다. 위의 상관식을 바탕으로 제습로터의 공기누설모델을 개발하였으며, 실험을 통해 측정된 값과 위 모델을 바탕으로 계산된 값을 비교함으로써 공기누설모델을 검증하였다. 그리고 풍량에 따른 제습로터의 성능실험을 수행하였으며, 공기누설모델을 적용한 성능 분석을 통하여 실질적인 제습량과 공기누설량을 확인 하였다. 또한 동일한 제습로터가 적용된 제습냉방시스템을 고려하여 차압변화에 따른 공기누설의 영향을 공기누설모델을 이용하여 고찰하였다.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 1988년도 춘계학술대회 논문집
• /
• pp.70-73
• /
• 1988

Influence of Velocity and Temperature on Streaming Electrification of Insulating Oil is investigated by injection method. Leakage current is increased slightly with increasing temperature in the temperature range 20 to $80^{\circ}C$ at low flow rate, however, it show a peak in the temperature 40 to $60^{\circ}C$ at high flow rate. Leakage current is also increased linearly with increasing flow rate in the flow rate range 1 - 31/min but thereafter, it is increased abruptly with increasing flow rate.

• 대한기계학회논문집B
• /
• 제21권10호
• /
• pp.1339-1349
• /
• 1997

A numerical method of calculating the performance of a scroll compressor for refrigerant R-22 and R-134a is presented in this paper. A series of involute curves are employed for the scroll wrap design and the compression volume is investigated geometrically. The radial leakage flow rate through tip clearance is calculated by the two-dimensional compressible flow. On the basis of the results, quasi one-dimensional leakage modeling can be applied to the performance analysis of a scroll compressor, more effectively. Furthermore, the heat transfer effect between scroll wrap and working fluid in compression chamber is considered for the performance analysis. As the results of this study, the effects of the radial and tangential leakage flow rate and heat transfer on the scroll compressor performance are derived precisely. These results may provide the guideline for the design and development of a real scroll compressor.

• 대한기계학회논문집
• /
• 제16권4호
• /
• pp.795-802
• /
• 1992

본 연구에서는 일정한 각도의 분사를 갖는 평씨일(plain seal)에 대하여 각 인자들이 누수성능에 미치는 영향을 수치적으로 조사하였다. 인자들로는 축방향 레 이놀즈수, 축회전속도, 분사의 유입속도, 간극비, 분사의 위치 및 유입각 등이 고려되 었다.

• 한국항공우주학회지
• /
• 제43권12호
• /
• pp.1108-1115
• /
• 2015

본 연구에서는 마우스피스 방법을 이용하여 산소의 질량유량 측정과 헬륨의 체적유량 측정에 대한 관계식을 정리하였다. 마우스피스 방법은 상사된 실험식을 이용함으로써 시험비용을 절감할 수 있다. 마우스피스 방법에서는 기체헬륨을 측정하여 용이하게 액체산소의 누설량을 측정할 수 있다. 시제품의 누설량 측정에서 상온과 극저온 상태의 헬륨과 산소간의 누설량 관계를 이해하기 위해 실험을 수행하여 비교하였다. 헬륨의 누설 체적유량[$A.m{\ell}/s$]은 액체상태의 산소 누설의 질량유량[g/s]에 대비하여 174배였다. 실험식과 비교된 계산식은 미국 국립기술표준원의 자료를 이용하여 증명하였다.