• 대한전자공학회논문지
• /
• 제23권4호
• /
• pp.550-556
• /
• 1986

This paper proposes a two-layer channel routing algorithm using the division of signal nets in LSI/VLSI layout design. To solve the vertical constraint problem, the doglegging method is used. Although signal net division and the dogleg are used, the routing is accomplished within local channel density and the increase in vias is repressed by assining the vertical segments to the metal layer and the horizontal segments to the poly layer. The algorithm was implemented on a VAX 11/780 computer. The effectiveness of the proposed algorithm is proved by appling this algorithm to Deutch's difficult example.

• International Journal of Fuzzy Logic and Intelligent Systems
• /
• 제5권1호
• /
• pp.13-20
• /
• 2005

This paper addresses a new blind channel equalization method using fourth-order cumulants of channel inputs and a three-layer neural network equalizer. The proposed algorithm is robust with respect to the existence of heavy Gaussian noise in a channel and does not require the minimum-phase characteristic of the channel. The transmitted signals at the receiver are over-sampled to ensure the channel described by a full-column rank matrix. It changes a single-input/single-output (SISO) finite-impulse response (FIR) channel to a single-input/multi-output (SIMO) channel. Based on the properties of the fourth-order cumulants of the over-sampled channel inputs, the iterative algorithm is derived to estimate the deconvolution matrix which makes the overall transfer matrix transparent, i.e., it can be reduced to the identity matrix by simple recordering and scaling. By using this estimated deconvolution matrix, which is the inverse of the over-sampled unknown channel, a three-layer neural network equalizer is implemented at the receiver. In simulation studies, the stochastic version of the proposed algorithm is tested with three-ray multi-path channels for on-line operation, and its performance is compared with a method based on conventional second-order statistics. Relatively good results, withe fast convergence speed, are achieved, even when the transmitted symbols are significantly corrupted with Gaussian noise.

• 신재생에너지
• /
• 제2권4호
• /
• pp.78-85
• /
• 2006

Selection of flow channel in the separation plate of PEMFC is very important parameter to improve its performance and reduce parasite loss. Flow patterns in the channel have great influence on the transport of hydrogen and air and removal of water generated from electrochemical reaction in diffusion layer. In this study. fluid flow in flow channel with parallel and interdigitated patterns are simulated three dimensionally on full flow domain including anode and cathode channel together. The numerical results show that the fuel cell with interdigitated flow channel represents better performance than that with parallel flow channel due to its strong convective transport across the gas diffusion layer. But the pressure drop in parallel flow channel is much more than that in interdigitated flow channel. And effects of temperature and stoichiometric number on performance can be calculated and analyzed as well. Nomenclature.

• 대한전자공학회:학술대회논문집
• /
• 대한전자공학회 2000년도 추계종합학술대회 논문집(2)
• /
• pp.317-320
• /
• 2000

We have calculated the optimum refractive index and thickness for a single layer antireflection coating as a function of active layer width and thickness in buried channel waveguides. The results using the variational method to obtain the field profiles are compared to those using the effective index method.

• 한국신재생에너지학회:학술대회논문집
• /
• 한국신재생에너지학회 2006년도 추계학술대회
• /
• pp.407-410
• /
• 2006

Selection of flow channel in the separation plate of PEMFC is very important parameter to improve its performance and reduce parasite loss. Flow patterns in the channel have great influence on the transport of hydrogen and all and water generated from electrochemical reaction in diffusion layer In this study, fluid flow in flow channel with parallel and interdigitated patterns are simulated three dimensionally on full flow domain including anode and cathode electrode together. The numerical results show that the fuel cell with interdigitated flow channel represents better performance than that with parallel flow channel due to its strong convective transport across the gas diffusion layer. But the pressure drop in parallel flow channel is much more than that in nterdigitated flow channel. The effect of temperature and stoichiometric number on performance can be calculated and analyzed as well.

• 한국정보과학회논문지:정보통신
• /
• 제27권2호
• /
• pp.206-218
• /
• 2000

에러율이 높은 무선채널 상에서 낮은 CLR(cell loss ratio)을 보장하는 ATM(asynchronous transfer mode) ABR(available bit rate) 서비스를 지원하기 위해서는 재전송이 요구된다. 무선 ATM에서는 ATM계층 하에 DLC(data link control)계층을 두어 DLC계층이 무선채널 상의 에러로 인해 요구되는 재전송과 재배열을 수행하도록 하여 높은 에러율을 갖는 무선채널의 특성이 낮은 에러율을 가정하여 설계된 ATM계층으로 전파되는 것을 막는다. 본 논문에서는 무선채널 상에서의 높은 에러율에 의한 전송률 감소를 반영하는 ABR 전송률 제어 방안을 제안함으로써 근원지의 전송률을 무선채널 상에서의 전송률에 보다 가깝게 맞추어 AP(access point)에서 발생할 수 있는 버퍼 오버플로우에 의한 셀손실을 줄였다. 채널의 상태를 ATM계층에 알리는 DLC계층을 가정한 모의실험을 통하여 제안하는 방안이 무선채널 상에서 기존의 방법보다 작은 크기의 ABR 큐를 사용하여 낮은 CLR을 보장함을 보였다. 또한 채널의 상태에 따라 전송률을 조정하는 DLC계층을 사용함으로써 무선 ATM에서 귀중한 자원인 무선링크를 보다 효율적으로 사용할 수 있음을 보였다.

• 대한전자공학회:학술대회논문집
• /
• 대한전자공학회 2001년도 하계종합학술대회 논문집(1)
• /
• pp.57-60
• /
• 2001

This paper has studied the WAP packet transmission time, using WTP SAR algorithm. One method that is improved transfer ability, SAR fragmented WTP total message down from upper layer and then packet is transmitted to RLP frame time slot. In this paper, we analysis the transmission time of WAP packet with variable HLP layer size on the CDMA wireless channel for next generation systems as well as PCS, DCS. From the results, we can obtain the WAP packet transmission time and optimal WTP packet size.

• 대한전기학회논문지:시스템및제어부문D
• /
• 제51권9호
• /
• pp.423-430
• /
• 2002

The fabrication and experimentation of multi-channel electrodes which enable detecting and recording of multi-site neuronal signals have been investigated. A multi-channel electrode array was fabricated by depositing 2000${\AA}$ thick Au layer on the 1000${\AA}$ thick Ti adhesion layer on a glass wafer. The metal paths were patterned by wet etching and passivated by depositing a PECVD silicon nitride insulation layer to prevent signals from intermixing or cross-talking. After placing a thin slice of rat cerebellar granule cell in the culture ring located in central portion of the multi-channel electrode plate, a neuronal signal from an electrode which is in contact with the cerebellar granule cell has been detected. It was found that the electrode impedance ranges 200㏀∼1㏁ and the impedance is not changed by cleaning with nitric acid. Also, the impedance is inversely proportion to the exposed electrode area and the cross-talk is negligible when the electrode spacing is bigger than 600$\mu\textrm{m}$. The amplitude and frequency of the measured action potential were 38㎷ and 2㎑, which are typical values. From the experimental results, the fabricated multi-channel electrode array proved to be suitable for multi-site neuronal signal detection for the analysis of a complicated cell network.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2010년도 하계학술대회 논문집
• /
• pp.350-350
• /
• 2010

Silicon carbide (SiC), one of the well known wide band gap semiconductors, shows high thermal conductivities, chemical inertness and breakdown energies. The design of normally-off 4H-SiC VJFETs [1] has been reported and 4H-SiC VJFETs with different lateral JFET channel opening dimensions have been studied [2]. In this work, 4H-SiC based VJFETs has been designed using the device simulator (ATLAS, Silvaco Data System, Inc). We varied the n-epi layer thickness (from $6\;{\mu}m$ to $10\;{\mu}m$) and the channel width (from $0.9\;{\mu}m$ to $1.2\;{\mu}m$), and investigated the static characteristics as blocking voltages, threshold voltages, on-resistances. We have shown that silicon carbide JFET structures of highly intensified blocking voltages with optimized figures of merit can thus be achieved by adjusting the epi layer thickness and channel width.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1993년도 하계학술대회 논문집 B
• /
• pp.1289-1291
• /
• 1993

The hydrogenation effects on characteristics of polycrystalline silicon thin film transistors(poly-Si TFT's) of which the channel length varies from $2.5{\mu}m\;to\;20{\mu}m$ and poly-Si layer thickness is 50, 100, and 150 nm was investigated. After 1 hr hydrogenation annealing by PECVD, the threshold voltage shift decreased dependent on the channel length, but channel width may not alter the threshold voltage shift. In addition to channel length, the active poly-Si layer thickness may be an important parameter on hydrogenation effects, while gate poly-Si thickness may do not influence on the characteristics of TFT's. Considering our experimental results, we propose that channel length and active poly-Si layer thickness may be a key parameters of hydrogenation of poly-Si TFT's.