• Structural Engineering and Mechanics
• /
• v.23 no.6
• /
• pp.651-674
• /
• 2006

The fatigue cracks initiate and propagate in the Armored Vehicle Launch Bridge (AVLB) components, especially like the splice doubler angle, splice plate, and bottom chord, due to the cyclic loading by repeated AVLB-launchings and tank-crossings. In this study, laboratory fatigue tests were conducted on six aluminum 2014-T6, four aluminum 7050-T76511, and four ASTM A36 steel compact-tension specimens to evaluate the crack growth behavior of the materials used for the components. The experimental results provide the relationship (Paris Law) between crack growth rate, da/dn, and stress intensity range, ${\Delta}K$, whose material dependent constants C and m can later be used in the life estimation of the components. Finite Element Method (FEM) was used to obtain the stress intensity factor, K, of the components with cracks. Because of the complexity of loading conditions and component geometry, several assumptions and simplifications are made in the FEM modeling. The FEM results, along with the results obtained from laboratory fatigue tests, are then utilized to estimate critical crack length and remaining life of the components.

• Current Industrial and Technological Trends in Aerospace
• /
• v.8 no.1
• /
• pp.86-95
• /
• 2010

Flight termination system(FTS) is used to terminate safely the launch vehicle's flight when it faces an emergency situation by transmitting termination command from ground FTS. RCC standard IRIG tone method has been used widely for FTS commands method in foreign ranges and Naro Space Center, but this method has a weakness for security of command signal. Therefore RCC had studied more secured EFTS standard and chose CPFSK digital modulation method. This paper describes basic concept and types of FTS and FTS types which foreign ranges had applied and describes standardization of EFTS in the U.S. based on RCC EFTS study reports.

• Current Industrial and Technological Trends in Aerospace
• /
• v.8 no.1
• /
• pp.96-103
• /
• 2010

The propulsion systems such as upper stages of launch vehicles, orbiters, spacecrafts have to operate in the zero gravity environment. Because the flight condition where the vehicle undergoes is different from the normal gravity state, many studies have been being in progress. Fluid behavior in the zero gravity condition is differently shown in the normal gravity state because the importance of the intermolecular force, such as adhesion, cohesion, and surface tension is enlarged. In this paper, we investigate the characteristic of fluid behavior and describe effects and problems on the liquid propulsion system due to these fluid behavior. We also check which studies are in progress in order to solve these problems.

• Current Industrial and Technological Trends in Aerospace
• /
• v.8 no.1
• /
• pp.45-54
• /
• 2010

The goal of the paper is to discuss the recent trend of the configuration of high resolution LEO(Low Earth Orbit) EO(Earth Observation) satellites. The satellite configuration is decided by considering several factors such as mission, payloads, launch vehicle, propulsion and attitude control module. The advent of commercial companies selling satellite's images in 2000's requires additional changes of the satellite system to be capable of obtaining many high resolution images quickly. In order to meet customer's needs, the overall configuration of satellites is designed to be compact and stable without the loss of structural integrity and reliability. Among design changes, the configuration change of satellites is treated intensively in the paper.

• Journal of computational fluids engineering
• /
• v.7 no.4
• /
• pp.35-41
• /
• 2002

The projectile afterbodies for zero-lift drag reduction has been analyzed using the Navier-Stokes equations with the κ-εturbidence model. The numerical method of a second order upwind scheme has been used on an unstructured adaptive grid system. Base drag reduction methods that have been found effective on axisymmetric bodies are boattailing, base bleed, base combustion, locked vortex afterbodies and multistep afterbodies. In this paper, turbulence flow and pressure charateristics have been studied for geometries of multistep afterbodies. The important geometrical and flow parameters relevant to the design of such afterbodies have been identified by step number, length and height. The flow over multistep aftoerbodies or base have many kinds of compressible flow characteristics including expansion waves at the trailing edge, recompression waves, separation and recirculating flow in the base region, shear flow and wake flow. The numerical results have been compared and analyzed with the experimental data. The flow characteristics have been clearly shown.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.16 no.3
• /
• pp.88-93
• /
• 2017

In the present study, the ignition characteristics of liquid fuel were experimentally investigated. To quantify its ignitability as ignition characteristics, the minimum ignition energy (MIE) of liquid fuel was defined and measured under at the elevated oxygen concentrations and reduced atmospheric pressures which that are the most probable conditions likely to be encountered during operation of the space launch vehicle's operating process. The experimental results demonstrate that the measured MIE decreased with the increasing the oxygen concentration at given atmospheric pressures. When the atmospheric pressure was reduced from 1 atm to 0.2 atm at a fixed oxygen concentration, the measured MIE was found to vary with $P^{-2}$ but the lowest MIE was observed at 0.8 atm.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2001.05a
• /
• pp.546-551
• /
• 2001

Space Test Department at KARI(Korea Aerospace Research Institute) plans to carry out the GVT(Ground Vibration Test) for the KSR(Korea Sounding Rocket)-III FM(Flight Model) which is being developed by Space Technology R＆D Division. KSR-III will be an intermediate to the launch vehicle capable of carrying satellites to their orbits. GVT offers very important information to predict the behavior of KSR in its operation, and to develop the flight control and aerodynamic analysis. For development of test facilities, testing and analysis methods which can be used for the future test, Space Test Department has performed the GVT with KSR-II PFM(Proto-Flight Model) at Satellite Integration ＆ Test Center of KARl This paper discusses the procedures, techniques and the results of it. In this test, to simulate free-free condition, test object hung in the air by 4 bungee cords specially devised. The GVT was carried out using pure random excitation technique with MIMO(Multi-Input-Multi-Output) method with three electromagnetic shakers, and poly-reference parameter estimation was used to identify the modal parameters. As the result of the test, 11 mode shapes and modal parameters below 200㎐ were identified and compared with analytical results.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.15 no.1
• /
• pp.69-75
• /
• 2011

Firing tests have been carried out for a technology demonstration model of 75-tonf-class combustor which is to be used on the liquid rocket engine of a Korean space launch vehicle. Firing tests were done at 50% of the nominal flow rate because of incapability of the test facility and limit of the test bed strength. Through the low pressure firing tests of 75-tonf-class channel cooling thrust chamber, operability and stability at the ignition and combustion phases were confirmed. Additionally it was foreseen that the 75-tonf-class thrust chamber would satisfy the performance requirements.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.15 no.1
• /
• pp.76-82
• /
• 2011

The thrust axis alignment of the launch vehicle is very important because the misalignment causes the unstable attitude control and results in mission failure. Generally, optical methods such as digital theodolite and laser tracker and mechanical method such as turn table method are used to align the thrust axis. This article deals with the simple method using inclinometer based on the gravitational direction. The inclinometer indicates zero degree when that is located on the perpendicular plate to gravitational direction. This method needs two inclinometer, such as standard and alignment ones and uses the angle difference as the reference data to adjust the TVC actuator offset.

• Journal of ILASS-Korea
• /
• v.19 no.4
• /
• pp.174-181
• /
• 2014

This study investigates the effects of nanoparticle size and temperature on the thermal conductivity enhancement of water-based alumina ($Al_2O_3$) nanofluids, using the centrifuging method and relative centrifugal forces of differing magnitude to produce nanofluids of three different particles without involving any dispersants or surfactants. We determined the coupling dependency in thermal conductivity enhancement relative to nanoparticle size and temperature of the alumina nanofluids and also experimentally showed that the effect of temperature on thermal conductivity is strongly dependent on nanoparticle size. Also, our experimental data presented that the effective medium theory models such as the Maxwell model and Hasselman and Johnson model are not sufficient to explain the thermal conductivity of nanofluids since they cannot account for the temperature- and size-dependent nature of water-based alumina nanofluids.