• Geomechanics and Engineering
• /
• v.14 no.5
• /
• pp.459-466
• /
• 2018

By conducting uniaxial loading cycle tests on the coal rock with outburst proneness, the dilatation characteristics at different loading rates were investigated. Under uniaxial loading and unloading, the lateral deformation of coal rock increased obviously before failure, leading to coal dilatation. Moreover, the post-unloading recovery of the lateral deformation was rather small, suggesting the onset of an accelerated failure. As the loading rate increased further, the ratio of the stress at the dilatation critical point to peak-intensity increased gradually, and the pre-peak volumetric deformation decreased with more severe post-peak damage. Based on the laboratory test results, the lateral deformation of the coals at different depths in the #1302 isolated coal pillars, Yangcheng Coal Mine, was monitored using wall rock displacement meter. The field monitoring result indicates that the coal lateral displacement went through various distinct stages: the lateral displacement of the coals at the depth of 2-6 m went through an "initial increase-stabilize-step up-plateau" series. When the coal wall of the working face was 24-18 m away from the measuring point, the coals in this region entered the accelerated failure stage; as the working face continued advancing, the lateral displacement of the coals at the depth over 6 m increased steadily, i.e., the coals in this region were in the stable failure stage.

• Journal of Mechanical Science and Technology
• /
• v.15 no.7
• /
• pp.1013-1021
• /
• 2001

A series of rabbit common extensor tendon specimens of the humeral epicondyle were subjected to tensile tests under two displacement rates (100mm/min and 10mm/min) and different elbow flexion positions 45°, 90°and 135°. Biomechanical properties of ultimate tensile strength, failure strain, energy absorption and stiffness of the bone-tendon specimen were determined. Statistically significant differences were found in ultimate tensile strength, failure strain, energy absorption and stiffness of bone-tendon specimens as a consequence of different elbow flexion angles and displacement rates. The results indicated that the bone-tendon specimens at the 45°elbow flexion had the lowest ultimate tensile strength; this flexion angle also had the highest failure strain and the lowest stiffness compared to other elbow flexion positions. In comparing the data from two displacement rates, bone-tendon specimens had lower ultimate tensile strength at all flexion angles when tested at the 10mm/min displacement rate. These results indicate that creep damage occurred during the slow displacement rate. The major failure mode of bone-tendon specimens during tensile testing changed from 100% of midsubstance failure at the 90°and 135°elbow flexion to 40% of bone-tendon origin failure at 45°. We conclude that failure mechanics of the bone-tendon unit of the lateral epicondyle are substantially affected by loading direction and displacement rate.

• Journal of the Society of Disaster Information
• /
• v.14 no.3
• /
• pp.367-378
• /
• 2018

Purpose: The objective of this study is to present a reasonable safety management of the anchored in-situ wall systems constructed in the ground conditions consisting of multi-layered soils underlain by bedrocks in the urban area of Korea. Method: Field measurements collected from collapse case histories with deep excavations were analyzed for the safety management of the wall systems supported by the earth anchors in terms of lateral displacement rates. Results: The average maximum lateral displacement rate in a collapsed zone of the in-situ wall significantly increased upon the completion of the excavation. Particularly, the collapse of the in-situ wall system due to the sliding occurring along the discontinuities of the rock produced a considerably large lateral displacement rate over a relatively short period. Conclusion: For predicting and preventing the collapse of the wall system during or after the excavation work, the utilization of the safety management criteria of the in-situ wall system by the lateral displacement rate was found to be much more reasonable in judging the safety of earthworks than the application of the quantitative management criteria which have been commonly used in the excavation sites.

• Journal of Korean Neurosurgical Society
• /
• v.38 no.4
• /
• pp.265-268
• /
• 2005

Objective : With the increasing popularity of pedicle screw fixation devices for several indications, the safety and reliability of screw insertion in the small pedicle has become a major issue. Many studies have investigated the accuracy of screw placement after pedicle screw fixation using various method. The reported displacement rates have been very different. The purpose of the study is to investigate the proper placement of pedicle screw insertion in the lumbar spine on 26 consecutive patients. Methods : Between September and December 2003, 26 consecutive patients [16women and 10men] were analyzed after transpedicular screw fixation of the lumbar and lumbosacral spine. After pedicle screw fixation in this study, 2-mm slices of CT scan were performed in all patients to detect caudal and cranial deviation of screw and medial and lateral deviation. Pedcile screw placement related complication was evaluated clinically. Results : A total of 144 inserted pedicle were analyzed in 26patients, and 58pedicle screws [40.3%] were detected to be improper placement. There were 14level [9.0%] of caudal or cranial deviation and 44level [30.6%] of medial or lateral deviation to the pedicle. Extra-pedicle placement was found on 4levels [2.7%] with only lease of neurologic injury. Conclusion : Proper screw placement, though complication rate is low, is important not only for clinical symptom but also for biomechanics. Further study for screw placement related biomechanical changes is needed.

• Magazine of the Korean Society of Agricultural Engineers
• /
• v.28 no.4
• /
• pp.49-56
• /
• 1986

This study was carried out to investigate mechanical characteristics of the uniformly loaded skew-plate at 4 kinds of boundary condition : i) all edges are clamped (BC-1) , ii) all edges are simply supported (BC- 2), iii) two opposite edges are clamped and the other two edges are free (BC-3), and iv )two opposite edges are simply supported and the other two edges are free (BC-4). Various skew angles, 0$^{\circ}$, 10$^{\circ}$, 15$^{\circ}$, 30$^{\circ}$, 40: 45: and 60, of the plate were tested for the above boundary conditions. Resutts obtained from the study are summarized as follows ; 1.The lateral displacement at the center of a skew- plate was decreased as the skewangle increased at all of the boundary conditions. The decrements of the conditions of BC-3 and BC-4 were considerable. And, difference of the displacement between the boundary conditions was decreased as the skew-angle was increased. 2. X-moments (to the Y-axis) at the center of a skew- plate and the minimum principal moments were shown as a similar pattern of change with respect to the skew-angle variation between BC-i and BC-2 and between BC-3 and BC-4, and the pattern of change at the conditions of BC-3 and BC-4 were shown higher rates than those for the conditions of BC-i and BC-2 3.Y-moments (to the X- axis) at the center of a skew-plate and the maximum principal moment were decreased as the skew-angle increased in a similar pattern at all of the boundary conditions. 4.X-moments at the obtuse angle side of a skew-plate were shown as a parabolic pattern of change (frist increased after then decreased) as the skew-angle increased, and a skew-angle resulting the maximum absolute moment was depended on the boundary conditions. 5.Y-moments at the obtuse angle side of a skew-plate were affected by the skewangle much more at the boundary condtions of BC-2 and BC-4 than at the conditions of BC-i and BC-3. 6.Maximum principal moments at the obtuse angle side of a skew-plate at the skew angle of 40$^{\circ}$- 45$^{\circ}$ were resulted almost the same value at all of the boundary conditions .

• Journal of Animal Reproduction and Biotechnology
• /
• v.36 no.4
• /
• pp.239-246
• /
• 2021

The immunological sperm separation method is economical compared to the existing sorting method, and it is promising for the development of new technologies by reducing sperm damage. Wholemom (WM) is a sex-regulating protein that comprises on immunoglobulin G coupled with magnetic nanoparticles (MNPs) that responds to surface proteins derived from the Y chromosome in cattle. Y sperms are restricted in motility as the WM aggregates them, and the magnet could separate the non-aggregated cells. This study was conducted to investigate the effect of WM treatment on the characteristics of bull sperm. After treating sperm with WM and incubation for 6 h, the motility parameters including total motility, progressive motility, velocity average path, velocity straight line, amplitude of lateral head displacement, and linearity were significantly higher in the WM treatment group than in the control group (p < 0.05). Sperm viability and acrosome reaction rates were similar in both groups during each incubation period (p > 0.05). In conclusion, the immunological sperm sexing procedure using a monoclonal antibody conjugated with MNPs did not affect the characteristics of bull sperm. This study suggests that compared to other techniques, the immunological method for sperm sexing could classify sperm quickly and efficiently without the use of expensive equipment.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.18 no.1
• /
• pp.174-182
• /
• 2014

To monitor the wind-induced responses of buildings, conventional real-time kinematic (RTK) methods based on two global positioning system (GPS) receivers (e.g., a reference and a rover) are widely applied. However, these methods can encounter problems such as difficulty in securing and maintaining a space for a reference station. With the recently developed virtual reference station (VRS)-RTK approach, the position of a structure can be measured using only a rover receiver. In this study, to evaluate the applicability of VRS-RTK methods in monitoring the lateral structural responses of frame structures, we performed free vibration tests on a one-story frame model (the first natural frequency of 1 Hz) and a three-story frame model (the first natural frequency of 0.85 Hz). To assess the reliability of the displacement and acceleration responses measured by the GPS, we performed a concurrent measurement using laser displacement sensors and an accelerometer. The accelerometer results were consistent with the GPS measurements in terms of the time history and frequency content. Furthermore, to derive an appropriate sampling rate for the continuous monitoring of buildings, the errors in the displacement responses were evaluated at different GPS sampling rates (5, 10, 20 Hz). The results indicate that as the sampling rate increased, the errors in the displacement responses decreased. In addition, in the three-story model, all modal components (first, second, and third modes) could be recorded at a sampling rate of 20 Hz.

• Clinical and Experimental Pediatrics
• /
• v.48 no.8
• /
• pp.846-856
• /
• 2005

Purpose : To measure the peak myocardial tissue velocities and patterns of longitudinal motion of atrioventricular(AV) annuli and assess body weight and heart rates-related changes in normal children. Methods : Using pulsed wave Tissue Doppler Imaging(TDI), we measured peak systolic, early and late diastolic myocardial velocities in 72 normal children at six different sites in apical-4 chamber (A4C) view and at four different sites in apical-2 chamber(A2C) view and compared those values with each other, also observing effects with body weights and heart rates. Longitudinal motions of the AV annuli were measured at three different sites in A4C. Results : There were no significant differences of the TDI parameters between gender, ECHO-machines and among the three Doctors performing TDI. Peak myocardial velocities were significantly higher at the base of the heart than in the mid-ventricular region and in the right lateral ventricular wall than in the left lateral ventricular wall or IVS. The TDI parameters showed no significant correlation with fractional shortening(%). Peak systolic and early diastolic myocardial velocities had no correlation with heart rates, but peak late diastolic velocities and A/E ratio correlated positively with heart rates. Correlations between the TDI parameters and body weight were inconsistent. Absolute longitudinal displacement and % displacement were not differ between gender and not correlated with the TDI parameters. Conclusion : We measured the peak myocardial velocities with TDI and the longitudinal motion of the AV annuli using M-mode echocardiography in normal children. With more large scale evaluation, we may establish reference values in normal children and broaden clinical applicabilities in congenital and acquired heart diseases.

• Steel and Composite Structures
• /
• v.48 no.1
• /
• pp.43-57
• /
• 2023

The impacts of waste tire rubber (WTR) on the bending conduct of reinforced concrete beams (RCBs) are investigated in visualization of experimental tests and 3D finite element model (FEM) using both ANSYS and SAP2000. Several WTR rates are used in total 4 various full scale RCBs to observe the impact of WTR rate on the rupture and bending conduct of RCBs. For this purpose, the volumetric ratios (Vf) of WTR were chosen to change to 0%, 2.5%, 5% and 7.5% in the whole concrete. In relation to experimental test consequences, bending and rupture behaviors of the RCBs are observed. The best performance among the beams was observed in the beams with 2.5% WTR. Furthermore, as stated by test consequences, it is noticed that while WTR rate in the RCBs is improved, max. bending in the RCBs rises. For test consequences, it is clearly recognized as WTR rate in the RCB mixture is improved from 0% to 2.5%, deformation value in the RCB remarkably rises from 3.89 cm to 7.69 cm. This consequence is markedly recognized that WTR rates have a favorable result on deformation values in the RCBs. Furthermore, experimental tests are compared to 3D FEM consequences via using ANSYS software. In the ANSYS, special element types are formed and nonlinear multilinear misses plasticity material model and bilinear misses plasticity material model are chosen for concrete and compression and tension elements. As a consequence, it is noticed that each WTR rates in the RCBs mixture have dissimilar bending and rupture impacts on the RCBs. Then, to observe the impacts of WTR rate on the constructions under near-fault ground motions, a reinforced-concrete building was modelled via using SAP2000 software using 3-D model of the construction to complete nonlinear static analysis. Beam, column, steel haunch elements are modeled as nonlinear frame elements. Consequently, the seismic impacts of WTR rate on the lateral motions of each floor are obviously investigated particularly. Considering reduction in weight of structure and capacity of the members with using waste tire rubber, 2.5% of WTR resulted in the best performance while the construction is subjected to near fault earthquakes. Moreover, it is noticeably recognized that WTR rate has opposing influences on the seismic displacement behavior of the RC constructions.

• Korean Journal of Agricultural Science
• /
• v.46 no.1
• /
• pp.195-204
• /
• 2019

In this study, we examined the effect of a liposome-based extender (Optixcell) and a tris-citric egg-yolk extender (Triladyl) on the frozen-thawed spermatozoa characteristics and the calving rate. The percentages for the total motility of the frozen-thawed spermatozoa were similar in the Optixcell and Triladyl groups. However, among the motile spermatozoa with a straight line velocity (VSL) ${\geq}25{\mu}m/sec$, the curvilinear velocity (VCL, ${\mu}m/sec$), VSL (${\mu}m/sec$), average path velocity (VAP, ${\mu}m/sec$), amplitude of lateral head displacement (ALH, ${\mu}m$), beat cross frequency (BCF, Hz), and plasma membrane integrity of the frozen-thawed spermatozoa for the Optixcell group were significantly higher than those for the Triladyl group. Furthermore, the calving rate in the Optixcell group (79.0%) was higher than that of the Triladyl group (62.8%). However, the acrosomal membrane integrity of the frozen-thawed spermatozoa in the Optixcell and Triladyl groups was not significantly different. These results indicate that semen freezing with Optixcell improved the motility and plasma membrane integrity of frozen-thawed spermatozoa and the calving rate of Hanwoo cows (native Korean cattle). In conclusion, our results suggest that semen freezing with the liposome-based extender Optixcell is more efficient than with the tris-citric egg-yolk extender Triladyl for improved offspring production.