• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.29 no.1 s.232
• /
• pp.14-21
• /
• 2005

Laser chemical vapor deposition can be an effective technique for a rapid prototyping with ceramic materials, in particular. The objective of the study is to fabricate several 3-dimensional objects by stacking multi-layers as well as to find out some basic aspects of a rapid prototyping with laser chemical vapor deposition such as deposition characteristics with traversing speed of the laser, possible problems in stacking multi-layers etc. The limit speed of the laser that can grow a tilted SiC rod was found in this study, and laser directing writing that occurs over the limit speed was also investigated. Finally, a zigzag-shaped rod, a spiral-shaped rod, a wall and a square duct were successfully fabricated with laser chemical vapor deposition of tetramethylsilane

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.28 no.4
• /
• pp.481-488
• /
• 2004

Laser chemical vapor deposition can be used as a new approach for a rapid prototyping technique. The purpose of the study is to fabricate several 3-dimensional objects that are relatively simple as well as to find the characteristics of SiC rod growth that is the first step in developing a new rapid prototyping technique with laser chemical vapor deposition. In the study, SiC rods were generated with varying precursor pressure for 5 minutes. Deposition rates with varying precursor pressure, shapes of rods, surface roughness and component organization were investigated, in particular. Finally, several simple objects like a branch or a propeller were successfully fabricated using laser chemical vapor deposition.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.26 no.9
• /
• pp.1226-1233
• /
• 2002

The purpose of the present study was to examine some basic aspects of laser chemical vapor deposition that will be ultimately utilized for solid freeform fabrication of three dimensional objects. Specifically, deposition of silicon carbide (SiC) using tetramethylsilane (TMS) as precursor was studied for a rod grown by $CO_2$laser-assisted chemical vapor deposition. First, temperature distribution for substrate was analyzed to select proper substrate where temperature was high enough for SiC to be deposited. Then, calculations of chemical equilibrium and heat and mass flow with chemical reactions were performed to predict deposition rates, deposit profiles, and deposit components. Finally, several rods were experimentally grown with varying chamber pressure and compared with the theoretical results.

• Journal of the Korean Ceramic Society
• /
• v.53 no.6
• /
• pp.647-651
• /
• 2016

SiC films were prepared on glassy carbon substrates by laser chemical vapor deposition under a high pressure of $10^4Pa$ using a diode laser (wavelength = 808 nm) and a polysilaethylene precursor. (111)-oriented SiC films were formed at a deposition temperature ($T_{dep}$) range of 1150 - 1422 K. At $T_{dep}=1262K$, the SiC film with a high Lotgering factor of above 0.96 showed an exhibited pyramid-like surface morphology and flower-like grains. The highest deposition rate ($R_{dep}$) was $220{\mu}m\;h^{-1}$ at $T_{dep}=1262K$.

• Proceedings of the KSME Conference
• /
• 2003.04a
• /
• pp.1615-1620
• /
• 2003

The purpose of the study is not only to establish experimental system for laser chemical vapor deposition but also to find the characteristics of SiC rod growth that is the beginning step in developing technology of 3 dimensional prototyping with laser chemical vapor deposition. In this study, SiC rod was generated with varying TMS pressure for 5 minutes. Deposition rates with varying TMS pressure, shapes of rods, surface roughness and component organization were investigated, in particular.

• Proceedings of the Korean Society of Laser Processing Conference
• /
• 2004.10a
• /
• pp.18-21
• /
• 2004

• Laser Solutions
• /
• v.5 no.2
• /
• pp.17-22
• /
• 2002

Characteristics of micro carbon structures fabricated with laser-induced chemical vapor deposition (LCVD) are investigated. An argon ion laser (λ＝514.5nm) and ethylene gas were utilized as the energy source and precursor, respectively. The laser beam was focused onto a graphite substrate to produce carbon deposit through thermal decomposition of the precursor. Average growth rate of a carbon rod increased for increasing laser power and pressure. Micro carbon rods with good surface quality were obtained at near the threshold condition. Micro carbon rods with aspect ratio of about 100 and micro tubular structures were fabricated to demonstrate the possible application of this method to the fabrication of three-dimensional microstructures. Laser Raman spectroscopic analysis of the micro carbon structures revealed that the carbon rods are consisting of amorphous carbon.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2016.02a
• /
• pp.147.1-147.1
• /
• 2016

Hydrophobic thin films are variously applicable for encapsulation of organic devices and water repulsive glass, etc. In this work, the stability of hydrophobic characteristics of plasma polymerized tetrakis (trimethylsilyloxy) silane (ppTTMSS) thin films were investigated. The films were deposited with plasma enhanced chemical vapor deposition (PECVD) on the glass. The deposition plasma power and deposition pressure was 70 W and 600 mTorr, respectively. Thereafter, deposited films were treated by 248nm KrF excimer laser. Stability of hydrophobic properties of plasma polymerized tetrakis(trimethylsilyloxy)silane film surface was tested by excimer laser irradiation, which is thought to simulate severe outdoor conditions. Excimer laser irradiation cycles changed from 10 to 200 cycles. The chemical structure and hydrophobicity of ppTTMSS films were analyzed by using Fourier transform infrared (FTIR) spectroscopy and water contact angle (WCA) measurement, respectively. Absorption spectra peaks and WCA of excimer laser treated ppTTMSS films did not change notably. These results show that our ppTTMSS films possess stable hydrophobic properties.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2002.05a
• /
• pp.914-917
• /
• 2002

Fabrication of micro carbon structures and patterns using laser-assisted chemical vapor deposition is studied. Argon ion laser and ethylene were used to grow micro carbon rod through pyrolytic decomposition of the reaction gas. The influence of reaction gas pressure and incident laser power on the diameter and growth rate of the micro carbon rod was experimentally investigated. The diameter of micro carbon rods increases linearly with respect to the laser power but is almost independent of the reaction gas pressure. Growth rate of the rod changes little with gas pressure when the laser power remains below 1W. When the carbon rod was grown at near threshold laser power, a very smooth surface is obtained on the rod. By continuously moving the focusing lens in the direction of growth, a micro carbon rod with a diameter of 28 ${\mu}{\textrm}{m}$ and aspect ratio of 100 was fabricated.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2005.06a
• /
• pp.657-662
• /
• 2005

In this study, the deposition of micrometer-scale metallic interconnects on LCD glass for the repair of open-circuit type defects is investigated. Although there had been a few studies Since 1980 s for the deposition of metallic interconnects by laser-induced chemical vapor deposition, those studies mostly used continuous wave lasers. In this work, a third harmonic Nd:YLF laser (351nm) of high repetition rates, up to 10 KHz, was used as the illumination source and $W(CO)_6$ was selected as the precursor. General characteristics of the metal deposit (tungsten) such as height, width, morphology as well as electrical properties were examined for various process conditions. Height of the deposited tungsten lines ranged from 35 to 500 nm depending on laser power and scan speed while the width was controlled between $3\~50{\mu}$ using a slit placed in the beam path. The resistivity of the deposited tungsten lines was measured to be below 1 $O\cdot{\mu}m$, which is an acceptable value according to the manufacturing standard. The tungsten lines produced at high scan speed had good surface morphology with little particles around the patterns. Experimental results demonstrated that it is likely that the deposit forms through a hybrid process, namely through the combination of photolytic and pyrolytic mechanisms.