• 대한전자공학회:학술대회논문집
• /
• 대한전자공학회 2002년도 하계종합학술대회 논문집(2)
• /
• pp.29-32
• /
• 2002

This paper describes a novel structure of NMOSFET with elevated SiGe source/drain region and ultra-shallow source/drain extension(SDE)region. A new ultra-shallow junction formation technology. Which is based on damage-free process for rcplacing of low energy ion implantation, is realized using ultra-high vacuum chemical vapor deposition(UHVCVD) and excimer laser annealing(ELA).

• 한국광학회:학술대회논문집
• /
• 한국광학회 2008년도 하계학술발표회 논문집
• /
• pp.371-372
• /
• 2008

• 한국전기전자재료학회논문지
• /
• 제19권8호
• /
• pp.769-774
• /
• 2006

In this paper the ZnO thin films, which has used spotlight of next generation short wavelength LEDs and semiconductor laser were deposited based on RF magnetron sputtering is described. The temperature at substrate and work pressure, which has implemented in sputtering process of ZnO thin films were settle down at $100^{\circ}C$ and 15 mTorr respectively. The ZnO 5N has used target. The thickness of ZnO thin films was about $1.6{\mu}m$ which was measured by SEM analysis after the sputtering process. Structural properties of ZnO thin films by in-situ and atmosphere annealing were analyzed by XRD. Transformation of grain size and surface roughness were observed by AFM. XPS spectra showed that ZnO thin film had a peak positions corresponding to the $Zn_{2p}$ and the $O_{1s}$. As form above XPS, we confirmed that post-annealing condition changed the atom ratio of Zn/O and microstructure in ZnO thin films.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2008년도 추계학술대회 논문집 Vol.21
• /
• pp.430-430
• /
• 2008

Using multi plasma enhanced chemical vapor deposition system (Multi-PECVD), p-a-Si:H deposition layer as a $p^+$ region which was annealed by laser (Q-switched fiber laser, $\lambda$ = 1064 nm) on an n-type single crystalline Si (100) plane circle wafer was prepared as new doping method for single crystalline interdigitated back contact (IBC) solar cells. As lots of earlier studies implemented, most cases dealt with the excimer (excited dimer) laserannealing or crystallization of boron with the ultraviolet wavelength range and $10^{-9}$ sec pulse duration. In this study, the Q-switched fiber laser which has higher power, longer wavelength of infrared range ($\lambda$ = 1064 nm) and longer pulse duration of $10^{-8}$ sec than excimer laser was introduced for uniformly deposited p-a-Si:H layer to be annealed and to make sheet resistance expectable as an important process for IBC solar cell $p^+$ layer on a polished n-type Si circle wafer. A $525{\mu}m$ thick n-type Si semiconductor circle wafer of (100) plane which was dipped in a buffered hydrofluoric acid solution for 30 seconds was mounted on the Multi-PECVD system for p-a-Si:H deposition layer with the ratio of $SiH_4:H_2:B_2H_6$ = 30:120:30, at $200^{\circ}C$, 50 W power, 0.2 Torr pressure for 20 minutes. 15 mm $\times$ 15 mm size laser cut samples were annealed by fiber laser with different sets of power levels and frequencies. By comparing the results of lifetime measurement and sheet resistance relation, the laser condition set of 50 mm/s of mark speed, 160 kHz of period, 21 % of power level with continuous wave mode of scanner lens showed the features of small difference of lifetime and lowering sheet resistance than before the fiber laser treatment with not much surface damages. Diode level device was made to confirm these experimental results by measuring C-V, I-V characteristics. Uniform and expectable boron doped layer can play an important role to predict the efficiency during the fabricating process of IBC solar cells.

• Journal of Korean Vacuum Science & Technology
• /
• 제6권2호
• /
• pp.101-104
• /
• 2002

Er doped SiOx films have been synthesized by ion beam assisted deposition (IBAD). The morphology and microstructure of films and their annealing behaviors have been examined by using scanning electron microscopy and x-ray diffraction. The composition and properties of films have been systematically investigated.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1996년도 하계학술대회 논문집 C
• /
• pp.1440-1442
• /
• 1996

The laser annealing effects on the TEOS (Tetra-Ethyl-Ortho-Silicate) oxide of MOS (Al/TEOS/n+ Silicon) structures was investigated with different initial oxide conditions, such as breakdown field. The breakdown field increased up to the 170 $mJ/cm^2$ with increasing laser energy density and decreased at 220 $mJ/cm^2$. It is considered that the increase of breakdown field is originated from the restore of strains which exist mainly at the metal/oxide interface.

• Bulletin of the Korean Chemical Society
• /
• 제29권2호
• /
• pp.427-430
• /
• 2008

BaTiO3 and SrTiO3 thin films were fabricated on Pt/Ti/SiO2/Si substrate by the pulsed laser deposition process. The dependence of the deposited film quality upon the partial oxygen pressure during the deposition process was importantly examined. Regardless of the oxygen pressure, the as-deposited films were not fully crystallized. However, the film deposited at low oxygen pressure became well crystallized after the annealing process. It was concluded, therefore, that the partial oxygen pressure is reduced as low as possible during the deposition process and then anneal the as-deposited samples at ambient pressure to fabricate the well crystallized SrTiO3 and BaTiO3 films by laser ablation.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2006년도 하계학술대회 논문집 Vol.7
• /
• pp.430-431
• /
• 2006

This letter reports the fabrication of polycrystalline silicon thin-film transistors (poly-Si TFT) on flexible plastic substrates using amorphous silicon (a-Si) precursor films by sputter deposition. The a-Si films were deposited with mixture gas of argon and helium to minimize the argon incorporation into the film. The precursor films were then laser crystallized using XeCl excimer laser irradiation and a four-mask-processed poly-Si TFTs were fabricated with fully self-aligned top gate structure.

• 한국전기전자재료학회논문지
• /
• 제13권11호
• /
• pp.969-975
• /
• 2000

Laser direct writing of micro-patterned copper lines has been achieved by pyrolytic decomposition of copper formate films (Cu(HCOO)$_2$.4$H_2O$), as a metallo-organic precursor, using a focused CW Ar$^{+}$ laser beam (λ=514nm) on PCB boards and glass substrates. The linewidth and thickness of the lines wee investigated as a functin of laser power and scan speed. The profiles of the lines were measured by scanning electron microscope (SEM), surface profiler ($\alpha$-step) and atomic force measured by scanning electron microscope (SEM), surface profiler ($\alpha$-step) and atomic force microscopy (AFM). The electrical resistivities of the patterned lines were also investigated as a function of laser parameters using probe station and semiconductor analyzer. We compared resistivities of the patterned copper lines with these of the Cu bulk. Resistivities decreased due to changes in morphology and porosity of the deposit, which were about 3.8 $\mu$$\Omega$cm and 12$\mu$$\Omega$cm on PCB and glass substrates after annealing at 30$0^{\circ}C$ for 5 minutes.s.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 1999년도 제17회 학술발표회 논문개요집
• /
• pp.102-102
• /
• 1999

Visible photoluminescence(PL) in si-implanted SiO2 films on crystaline silicon were observed. Thermal oxide films of 1 ${\mu}{\textrm}{m}$ thickness on P-type crystal silicon were made and si+ ions were implanted with 200keV acceleration voltage on ti. Argon laser (wavelength 488nm) and PM tube were used for PL measurements. As annealing time increased at low temperature, the visible PL intensity are increased and the peak positions are changed. On the other hand, with increasing annealing time at high temperature, the visible PL intensity are disappeared. From the PL peaks and intensity changes, XRD results, and TEM observations, we will discuss the origin of PL in Si+-implanted SiO2 films with oxygen righ defects and silicon rich defects.