• 한국정보디스플레이학회:학술대회논문집
• /
• 2000.01a
• /
• pp.37-38
• /
• 2000

The ZnS:Tb thin-film electroluminescent devices were grown by atomic layer deposition with utilizing single-layer aluminum oxide and/or multilayered tantalum aluminum oxide, $Ta_xAl_yO$, as upper and lower insulating layers. These devices were investigated in terms of the luminescent and electrical characteristics. From this analysis, the devices using the $Ta_xAl_yO$ instead of $Al_2O_3$ were observed to have a lower threshold voltage for emission due to the higher relative dielectric constant of $Ta_xAl_yO$ insulators than that of the $Al_2O_3$ device. And there was a large amount of dynamic space charge generation in the phosphor of the device with the $Ta_xAl_yO$ insulators seemingly due to electron multiplication such as trap ionization.

• Journal of Information Display
• /
• v.10 no.2
• /
• pp.72-75
• /
• 2009

The Brillouin spectrum of 4'-n-pentyl-4-cyano-biphenyl (5CB) liquid crystals homogeneously confined in a planar liquid crystal (LC) cell was measured using a 6-pass tandem Fabry-Perot interferometer. By adopting a special right-angle scattering geometry, the sound velocity of 5CB was estimated from the Brillouin shift without knowing the refractive index. The sound velocity of the longitudinal wave propagating along the direction of the directors aligned parallel to the glass plates of the LC cell was 1784${\pm}$7 m/s at 300 K. The attenuation coefficient $\alpha$ was estimated to be approximately $1.9{\times}10^6m^{-1}$, which is about twice as large as that of the longitudinal sound wave propagating along the direction perpendicular to the directors. The present method may be very useful in the evaluation of the elastic properties of the materials used in display devices, whose refractive indices are not known.

• Journal of the Semiconductor & Display Technology
• /
• v.21 no.4
• /
• pp.1-5
• /
• 2022

We presented a micro hemi-sphere structure flexible film to improve the external quantum efficiency (EQE) in OLEDs. The micro hemi-sphere flexible film was fabricated with breath figure (BF) method and replica process. At 45 mg/mL of concentration, the size of the hemi-spheres was approximately 6.2 ㎛ were obtained which are the most circular shape. So, it was possible to yield the best performance with an improvement of 33 % in the EQE and the widest viewing angle ranging from 0° to 70°. As a result, the hemi-sphere film's size and distribution seem to play important roles in enhancing the EQE in OLEDs. Furthermore, the flexible hemi-sphere film based on polymeric materials could offer an effective, large-scale, mass-produced product and a simple process and approach to achieve high efficiency in flexible OLEDs.

• Proceedings of the Korea Information Processing Society Conference
• /
• 2014.11a
• /
• pp.1183-1186
• /
• 2014

Our research is different form traditional to have some large LED screen grouping together to constitute multi-vision technique. In this paper, we purpose a method of using k-path diffusion method to build connect between the devices and find an optimal data transmission path. In second half of this paper, through practical application, we using this technique transmitting data successfully and achieving a simple Multi-vision effect. This technique possess smart devices and Wifi P2P's features, these features improve system's dynamic and decentralized processing ability make our technique has high scalability.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2011.05a
• /
• pp.2.2-2.2
• /
• 2011

In this talk, the general concept of roll-to-roll printing technologies will be introduced with basic fundamentals of ink formulations for printing electronic devices as the first part of the talk. As the second part, based on the R2R printing process, key factors for printing TFTs, IC, PV and display would be presented using the information from the case study of R2R gravure and offset.

• Journal of the Semiconductor & Display Technology
• /
• v.22 no.4
• /
• pp.26-31
• /
• 2023

We investigated the impact of NF₃ / H₂O remote plasma dry cleaning conditions on the SiO₂ etching rate at different preparation states during the fabrication of ultra-large-scale integration (ULSI) devices. This included consideration of factors like Si crystal orientation prior to oxidation and three-dimensional structures. The dry cleaning process were carried out varying the parameters of pressure, NF₃ flow rate, and H₂O flow rate. We found that the pressure had an effective role in controlling anisotropic etching when a thin SiO₂ layer was situated between Si₃N₄ and Si layers in a multilayer trench structure. Based on these observations, we would like to provide further guidelines for implementing the dry cleaning process in the fabrication of semiconductor devices having 3D structures.

• KSII Transactions on Internet and Information Systems (TIIS)
• /
• v.14 no.2
• /
• pp.871-888
• /
• 2020

With the development of display engineering and technology, the screen and sound quality of information devices such as TVs are improving. The screen used LEDs via LCD and PDP and a large flat panel in the early CRT to create super-high resolution. The sound is improved by directly vibrating a thin and simple panel, such as an OLED. In our previous study, the exciter speaker was attached to the rear of the OLED panel to be used as the diaphragm of the speaker, and the sound quality was as good as that of the TV using the existing dynamic speaker. This method supplied the viewer with the direct sound coming from the panel, delivering clear sound, and the sound and image came from the same location, thus giving the viewer high immersion and maximizing the effect of information transfer. OLED exciter speakers, however, have a special directivity, which tends to slightly attenuate the tone at the very center of the screen. This study improves the sound quality by improving the structure of the exciter speaker and the radiated sound of the flat panel display. A 2-in-1 Exciter is made into a single core to improve the speaker's radiation pattern.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2003.06a
• /
• pp.292-295
• /
• 2003

Moire topography method is a well-known non-contacting 3-D measurement method. the automatic 3-D measurement by moire topography has been required since the method was frequently applied to the engineering and medical fields. 3-D measurement using digital projection moire topography is very attractive because of its high measuring speed and high sensitivity. In this study, digital two-wavelength phase shilling moire is applied to the entertainment fields. recently. as promoting the growth of the VR-Game, display devices which attract public attention such as HMD or Projector are being appeared in order to deliver effectively the absorption sense. this study realized the Auto-calibrating system for arbitrary display surface using digital moire method which satisfied the shape measurement of display surface and the request of FOV(Field of View) output. also when large screen wasn't prepared, this auto-calibrating system was applied to enjoy games or movies at home with a projector and walls

• Journal of the Korean Society of Industry Convergence
• /
• v.25 no.6_2
• /
• pp.1029-1036
• /
• 2022

The traditional outdoor advertising market has been stagnant recently, but the digital advertising market has been steadily increasing, and the digital signage market has been expanding despite the recent corona pandemic. However, in terms of hardware, new displays are required due to excessive power consumption, lack of visibility in sunlight, and continuous operating expenses. Since the e-paper display does not require a light emitting device therein, it is advantageous to solve above problems. In addition, it has the advantage of consuming power only when converting an image due to bistability, so it is suitable as hardware that implements images rather than moving pictures. Currently, one of the most successful examples of commercializing e-paper displays is ESL devices. According to a recent market study, the market for large-sized panels larger than 10 inches has grown at an annual rate of 21.6%, and the market is expected to exceed 30% by 2026. It is judged that it will be relatively easy to apply the roll-to-roll technology, which is currently developing the technology applied to OLED, to the e-paper display. Therefore, mass production technology and market expansion for ESL panel enlargement are expected, and a new market is also expected to be formed at the same time. New markets will be traffic signs, public displays, billboards, façades, kiosks, digital signage, and so on.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2006.08a
• /
• pp.305-308
• /
• 2006

Advanced mobile communication devices require a bright, high information content display in a small, light-weight, low power consumption package. For portable applications flexible (or conformable) and rugged displays will be the future. In this paper we outline our progress towards developing such a low power consumption active-matrix flexible OLED $(FOLED^{TM})$ display. We demonstrate full color 100 ppi QVGA active matrix OLED displays on flexible stainless steel substrates. Our work in this area is focused on integrating three critical enabling technologies. The first technology component is based on UDC's high efficiency long-lived phosphorescent OLED $(PHOLED^{TM})$ device technology, which has now been commercially demonstrated as meeting the low power consumption performance requirements for mobile display applications. Secondly, is the development of flexible active-matrix backplanes, and for this our team are employing PARC's Excimer Laser Annealed (ELA) poly-Si TFTs formed on metal foil substrates as this approach represents an attractive alternative to fabricating poly-Si TFTs on plastic for the realization of first generation flexible active matrix OLED displays. Unlike most plastics, metal foil substrates can withstand a large thermal load and do not require a moisture and oxygen permeation barrier. Thirdly, the key to reliable operation is to ensure that the organic materials are fully encapsulated in a package designed for repetitive flexing, and in this device we employ a multilayer thin film Barix encapsulation technology in collaboration with Vitex systems. Drive electronics and mechanical packaging are provided by L3 Displays.