• Journal of the Korean Wood Science and Technology
• /
• v.25 no.2
• /
• pp.67-74
• /
• 1997

A relationship between drying resistance and moisture content was found for 24, 27 and 30mm thick boards, and 45, 51 and 57mm thick dimensions of Japanese larch. Dahurian larch and radiata pine in order to modify the kiln schedule by using time schedules. The amount of drying resistance for Dahurian larch lumber was the highest, and radiata pine lumber was the lowest, on the basis of the same moisture content range. Drying resistance increased curvilinearly as moisture content decreased, and was higher for thicker lumber than for thinner lumber, at a given moisture content. Combined drying resistance for the three board thicknesses and the three dimension thicknesses showed a comparatively strong for radiata pine and a Japanese larch, while a weak correlation for Dahurian larch as a function of two independent variables, thickness and moisture content of lumber, respectively.

• Journal of the Korean Wood Science and Technology
• /
• v.43 no.2
• /
• pp.186-195
• /
• 2015

This study aims at modeling the rotary drying of wood chips in co-current mode and estimating the drying time of larch (Larix kaemferi) wood chip. Drying data were obtained in a lab. scale fixed bed dryer operating with an air velocity of 1 m/sec. and at hot air inlet temperatures of $100^{\circ}C$, $200^{\circ}C$, and $300^{\circ}C$. The lab. scale fixed-bed drying rates for small, medium and large size larch wood chips that had been dried from 40% wet-based moisture content (MC) to 10% MC at $200^{\circ}C$ drying temperature were 17.3 %/min., 10.2 %/min. and 5.5 %/min., respectively. It was predicted that larch large size wood chips could be dried from 40% MC to 10% MC in about 23.0, 34.6, and 44.7 minutes at $300^{\circ}C$, $200^{\circ}C$ and $150^{\circ}C$, respectively. Expected drying times for medium size chips were about 8.6, 11.2 and 13.2 minutes and those for small size chips were 4.3, 5.5 and 6.4 minutes, respectively.

• Journal of the Korean Wood Science and Technology
• /
• v.50 no.4
• /
• pp.237-245
• /
• 2022

This study examined the structural performance of experimental parallel strand lumber (PSL) from a Larch veneer strand. The prototype of PSL from a Larch veneer strand was manufactured in the experimental laboratory and tested. The bending and dowel bearing strength were determined from the modulus of elasticity (MOE), modulus of rupture (MOR), and dowel bearing strength based on a 5% offset yield load. The test results indicated that the average MOR of PSL was higher than that of 2 × 4 dimension lumber, and the average MOE of PSL was lower than that of 2 × 4 dimension lumber. A linear relationship was observed between the MOR and MOE. The allowable bending stress of PSL was derived as specified in ASTM D2915 and compared with other research. The dowel bearing strength of PSL in parallel to the grain was approximately double that perpendicular to the grain of PSL. A comparison of several theoretical calculations based on each national code for the dowel bearing strength was conducted, and some theoretical equations produced results closer to the experimental results when it was parallel to the grain, but the difference was higher in the case perpendicular to the grain. The test results showed that PSL made with Japanese larch veneer strands appeared to be suitable for a raw material of structural composite lumber (SCL) appeared to be used as a raw material for SCL.

• Journal of Forest and Environmental Science
• /
• v.40 no.1
• /
• pp.35-42
• /
• 2024

The Japanese larch (Larix kaempferi [Lamb.] Carriere) is a major timber species in Korea. However, studies on bucking rates and merchantable logs of this species are insufficient in South Korea. To bridge these gaps, in this study, the bucking rate of Japanese larch (Larix kaempferi [Lamb.] Carriere) was computed and the number of long logs and merchantable log volumes were analyzed. Sample trees were bucked according to the log grade for trading, and collected from a forest field in Gangwon Province. The bucking rate of all Japanese larch logs was >89%. The highly profitable 2-4 logs of 3.6 m length from trees with ≤30 cm diameter at breast height (DBH) and 5-6 logs with ≥34 cm DBH were produced. The bucking rate of long logs was >84%; thus, Japanese larch was found to be suitable for the supply of high-grade timber. Additionally, to follow reasonable wood supply plans, merchantable volume tables were offered based on 3.6 m-long number of logs and small-end diameter classes. Understanding the proportion of merchantable log volumes, bucking rates, and the number of long and short logs has large-scale applications in practical forestry.

• The Korean Journal of Ecology
• /
• v.8 no.1
• /
• pp.15-19
• /
• 1985

A number of field surveys have been performed in larch (Larix leptolepsis) forest floor in which any seeding of this species never find ther. In laboratory work, aqueous extracts from leaves, roots and stems of larch were provided and used to bioassay. Among them, germination and seedling growth of selected species were the most inhibitory in leaves extracts. Though germiation percentage of a species showed high compared with control, its dry weight after a given period grown were clearly low. The results due to be considered by allelopathic effect. And syringic acid and p-hydroxybenzoic acid were identified by HPLC from larch leaves. It is assumed that these phenolic acids affect on other species as allelochemicals of larch.

• Journal of the Korea Furniture Society
• /
• v.27 no.4
• /
• pp.302-308
• /
• 2016

It has been known that acetylation improves the dimensional stability of wood. Liquid phase acetylation is more popular than gas-phase acetylation for the effectiveness of weight gain of wood. In this study the specimens of domestic red and Korean pines are acetylated in liquid phase and their physical properties, such as density, bending strength, anti-hygroscopicity etc., are analyzed. Acetylation increases the average weights and volume of larch specimens by 11.4% and 3.4%, respectively, and their average oven-dry densities are increased by $0.03g/cm^3$. Acetylation does not influence on Modulus of Rupture (MOR) and Modulus of Elasticity (MOE). The average Percentage Reduction in Hygroscopicity (PRH) and average Percentage Reduction in Water soaking (PRW) of larch specimens are respectively 20.2% and 20.8%. Thus it can be concluded that acetylation improves the dimensional stability of larch specimens.

• Journal of the Korean Wood Science and Technology
• /
• v.8 no.2
• /
• pp.6-8
• /
• 1980

Japanese larch veneer, Cryptomeria veneer and japanese cypress veneer were peeled with condition of nose bar pressure at 5%, 10%, 15%, to find the optimum nose bar pressure. 1. Optimum nose bar pressure was 15% in 2mm thickness veneer of japanese larch. 2. Optimum nose bar pressure was 5% in 2mm thickness veneer of Cryptomeria. 3. Optimum nose bar pressure was 15% in 2mm thickness veneer of japanese cypress.

• Journal of Korean Society of Forest Science
• /
• v.6 no.1
• /
• pp.1-5
• /
• 1967

We studied on the bark Percentage of red pine (Pinus denssiflora S & Z) and tarch (Larix Kaemdferi sargent) and obtained the results as follows: (1) For diameter classes from 8 to 38 cm in red pine. the linear equation adopts the relation of the bark percentage to the diameter more accurately than the logarithmic equation. (2) The difference between the regression equation of the bark percentage between red pine and Larch is significant and the correlation cofficient in red Pine is high so that standard error of red Pine is lower than its value of Larch. We established, therefore the tables of bark percentage for each species by applying the following regression equations. red Pine Y=10.08205-0.08794x Larch Y=10.3527-0.17071x.

• Journal of Korean Society of Forest Science
• /
• v.83 no.4
• /
• pp.512-520
• /
• 1994

To enhance the utilization of Larch(Larix leptolepis Gorden) wood, the sawdusts were tested as cultivating media for Lentinus edodes(Mori 290) by varying the composition of the media. The economic efficiency for producing mushrooms from larch sawdusts was evaluated. The results are as follows. 1. Larch sawdust was as much efficient as oak sawdust in the growth of the mycelia and production of good quality of oak mushrooms. 2. The mushrooms were able to be harvested starting six months after beginning the cultivation. No differences were found among the qualities of the mushrooms produced by various treatments. 3. The contents of lignin(28.6-28.7%) in the fresh sawdust of larchwood are higher than those in the residues of the used media(18.2%). But lignin content of 1% NaOH extracts(30.4-34.4%) in fresh sawdust of larch was lower than those in the residues(68.0%). 4. The production of mushroom was relatively high to be 29.7-31.5%(760-780g.)/2.5kg pack) of mushroom weight. The net profit estimated was 1,475Won per pack.

• Journal of the Korean Wood Science and Technology
• /
• v.43 no.1
• /
• pp.122-134
• /
• 2015

This study was conducted to investigate the potential of torrefied larch wood as a raw material of pellets. First of all, larch chip was torrefied at the temperatures of 230, 250 and $270^{\circ}C$ for 30, 50 and 70 min. Secondly, moisture content, moisture absorption, higher heating value and ash content of the torrefied chip were measured to examine the effects of torrefaction conditions on the fuel characteristics of larch. Thirdly, surfaces of the torrefied chip were observed by light microscope (LM), field emission scanning microscope (FE-SEM) and SEM-energy dispersive spectroscopy (EDXS). With the increases of torrefied temperature and time, contents of lignin increased and those of hemicellulose reduced. Moisture content of torrefied larch chip was greatly lower than that of non-torrefied chip. Moisture absorption of the torrefied chip decreased as torrefaction temperature increased. As torrefaction temperature increased, higher heating value and ash content of larch chip increased. However, durability of torrefied-larch pellets was remarkably lower comparing to non-torrefied-larch pellets. When surface of larch chip was observed by LM and FE-SEM, surface color and cell wall of the chip was getting darker and more collapsed with the increases of torrefaction conditions. Through the analysis of SEM-EDXS, distribution and quantity of lignin existing on the surface of larch chip increased with the increases of torrefied conditions. In conclusion, $270^{\circ}C$/50 min might be an optimal condition for the torrefaction of larch with the aspect of fuel characteristics, but torrefaction condition of $230^{\circ}C$/30 min should be considered according to the durability of torrefied-larch pellets.