• Journal of Advanced Navigation Technology
• /
• v.23 no.5
• /
• pp.437-443
• /
• 2019

In this paper, a new algorithm for the calculation of the range between an LTE base station (BS) and a user equipment (UE) using time-of-arrival (TOA) measurements of LTE signals is proposed. First, the cell identity (cell ID) of the received signal is acquired using the primary synchronization signal (PSS) and secondary synchronization signal (SSS) to identify the BS transmitted the signal. The proposed algorithm exploits the cell-specific reference signal (CRS), the reference sequence inserted in commercial LTE signals, to estimate the time delay using 2D cross-correlation. The obtained TOA estimations can be used to calculate the range employed from the known BS location. The performance of the proposed algorithm is evaluated with the experiment performed using real LTE signals transmitted from the commercial BS.

• International Journal of Highway Engineering
• /
• v.10 no.2
• /
• pp.145-157
• /
• 2008

Load transfer efficiency (LTE) reflects the structural performance of doweled and undoweled joints of Jointed Concrete Pavement (JCP). A 3-dimensional (3-D) model of JCP was built using ABAQUS software in this study. Three concrete slabs were placed on bonded sublayers composed of a base and subgrade. Spring elements were used to connect the adjacent slabs at joints. Different spring constants were input to the model to simulate different joint stiffness of the concrete pavement. The LTE of the joint increased with an increase of the spring constant. The effects of material properties and geometric shape on the behavior of JCP were analyzed using different elastic modulus and thickness of the slab and base in the modeling. The results showed the elastic modulus of the subgrade affected the behavior of the slab and LTE more than that of the base and the thickness of the slab and base. The effects of a negative temperature gradient on the behavior of the slab and LTE were more than that of positive and zero temperature gradients. Joints with low stiffness were more sensitive to the temperature gradient of the slab.

• The Journal of Korea Institute of Information, Electronics, and Communication Technology
• /
• v.7 no.4
• /
• pp.188-194
• /
• 2014

In this paper, an antenna which has quad band in LTE (0.746 ~ 0.798 GHz), GSM(0.824 ~ 0.960 GHz), DCS(1.71 ~ 1.88 GHz), WCDMA(1.91 ~ 2.17 GHz) is proposed. An antenna size is $122mm{\times}50mm{\times}0.8mm$ on FR4(${\epsilon}_r=4.4$) ground substrate. In the proposed antenna, branch line is applied to the conventional PIFA architecture to achieve multi-bandwidth. Coupling power supply is applied for a wide bandwidth. Result of the measurement is as follows. When the low frequency, the antenna presents gain of 0.93 ~ 1.92dBi, and radiation efficiency of 49.60 ~ 76.35 %, and When the high frequency, gain is 2.19 ~ 4.66dBi, and radiation efficiency is 60.40 ~ 80.01 %, and with a VSWR < 2 (${\leq}-10dB$)measurement results for standard satisfies all band. Judging from the result, proposed multiband antenna is expected to be applied. B4G mobile terminals since the antenna shows an outstanding performance.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.35 no.7A
• /
• pp.623-631
• /
• 2010

In this paper, various of pilot-assisted channel estimation techniques for 3GPP LTE downlink are tested under multipath Rayleigh fading channel. At first, the conventional channel estimation techniques are applied with linear zero-forcing (ZF) equalizer, such as one dimensional least square (1-D LS) linear interpolation, two dimensional (2-D) wiener filter, the time and frequency dimension separate wiener filter and maximum likelihood estimator (MLE). Considering the practical implementation, we proposed two channel estimation techniques by combining time-dimension wiener filter and MLE in two manners, which showed a good tradeoff between system performance and complexity when comparing with conventional techniques. The nonlinear decision feedback equalizer (DFE) which can show a better performance than linear ZF equalizer is also implemented for mitigating inter-carrier interference (ICI) in our system. The complexity of these algorithms are calculated in terms of the number of complex multiplications (CMs) and the performances are evaluated by showing the bit error rate (BER).

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.16 no.6
• /
• pp.825-831
• /
• 2016

In this paper, a transimpedance amplifier based on a new DC offset cancellation (DCOC) method is proposed for WCDMA/LTE applications. The proposed method applies a sample and hold mechanism to the conventional DCOC method with a DC feedback loop. It prevents the removal of information around the DC, so it avoids signal-to-noise ratio degradation. It also reduces area and power consumption. It was designed in a $0.13{\mu}m$ deep n-well CMOS technology and drew a maximum current of 1.58 mA from a 1.2 V supply voltage. It showed a transimpedance gain of $80dB{\Omega}$, an input-referred noise current lower than 0.9 pA/${\surd}$Hz, an out-of-band input-referred 3rd-order intercept point more than 9.5 dBm, and an output DC offset lower than 10 mV. Its area is $0.46mm{\times}0.48mm$.

• Journal of electromagnetic engineering and science
• /
• v.14 no.1
• /
• pp.1-8
• /
• 2014

A differential-cascode CMOS power amplifier (PA) with a supply modulator for envelope tracking (ET) has been implemented by 0.18 ${\mu}m$ RF CMOS technology. The loss at the output is minimized by implementing the output transformer on a FR-4 printed circuit board (PCB). The CMOS PA utilizes the $2^{nd}$ harmonic short at the input to enhance the linearity. The measurement was done by the 10MHz bandwidth 16QAM 6.88 dB peak-to-average power ratio long-term evolution (LTE) signal at 1.85 GHz. The ET operation of the CMOS PA with the supply modulator enhances the power-added efficiency (PAE) by 2.5, to 10% over the stand-alone CMOS PA for the LTE signal. The ET PA achieves a PAE of 36.5% and an $ACLR_{E-UTRA}$ of -32.7 dBc at an average output power of 27 dBm.

• KSII Transactions on Internet and Information Systems (TIIS)
• /
• v.8 no.9
• /
• pp.2967-2981
• /
• 2014

Device-to-Device (D2D) communication is a technology component for long-term evolution-advanced (LTE-A). In D2D communication, users in close proximity to each other can communicate directly without going through a base station; such direct communication can improve spectral efficiency. Although D2D communication brings improvement in spectral efficiency, it also causes interference to the cellular network as a result of spectrum sharing. In particularly, D2D communication can generate interference for each D2D pair when the common wireless medium in a co-located limited area is accessed. Even though the interference management for between the D2D pair and cellular networks has been proposed, the interference reducing methods have still not been fully studied for the D2D pairs. In this paper, we investigate the problem of D2D pair coexistence in which interference is considered between D2D pairs. Using a signal to interference model for a target D2D pair, we provide an analysis of the aggregated throughput of a dense D2D network. For a target D2D pair, we assume that the desired signal and interference signals obey multipath fading and shadow fading. Through analysis, we demonstrate the effect of cluster size such as the number of D2D pairs and the size of the considered area on the network performance. The analytical results are compared with computer simulations. Our work can be used for a rough guideline for controlling the system throughput in a dense D2D network environment.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.26 no.11
• /
• pp.1672-1678
• /
• 2022

In this paper, the relay antenna was designed in consideration of the performance of the 28GHz band 5G mobile communication relay horn antenna, such as radiation pattern and return loss. A horn array for 5G mobile communication repeater was designed by arranging the antenna elements in phase, and the performance was analyzed. Unlike conventional WCDMA (3G) and LTE (4G), in millimeter wave band communication, high path loss occurs between transmission and reception. In the design of a 5G millimeter wave horn antenna, antenna performance such as isolation and gain between antenna elements as well as gain and bandwidth of the antenna must be additionally considered. The antenna gain of the single horn antenna (1×1) and the array horn antenna (2×4) in the 28GHz band is about 10.44d Bi and 19.58dBi, respectively, and the return loss is designed to be less than -18dB. It has proven its validity and has been shown to be suitable for application to 5G mobile communication relay system.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.40 no.8
• /
• pp.1532-1541
• /
• 2015

D2D(Device-to-Device) communication is a promising technology to improve the system capacity and spectral efficiency. By sharing the same radio resources with cellular user equipments, D2D communications can significantly enhance the overall spectral efficiency. However, it may cause interference between D2D link and cellular link. So, careful resource allocation and interference coordination between them are very important and need to be properly handled. This paper proposes a radio resource allocation scheme that decreases interference through the use of area grouping and D2D pair grouping. Simulations results are provided to verify the performance improvement of the proposed scheme in terms of the number of assigned resource blocks and computational complexity.

• Smart Media Journal
• /
• v.9 no.2
• /
• pp.16-21
• /
• 2020

Recently, mobile traffic is increasing exponentially as major traffic is transferred to IoT and visual media data in the dissemination of mobile communication terminals and contents use. In order to overcome the limitations of the existing LTE system, 5G mobile communication technology (5G) is a technology that meets 1000 times data traffic capacity, 4G LTE system acceptance, low latency, high energy efficiency, and high cost compared to 4G LTE system. The path loss due to the use of the frequency domain is very high, so it may be difficult to provide a service compared to the existing 4G LTE system. To overcome these shortcomings, various techniques are under study. In this paper, small cell technology is introduced to improve the system performance of 5G mobile communication systems. The performance is analyzed by comparing the results of small cell technology application, macro communication and small cell communication, and the results of the proposed algorithm application for power control. The analysis results show that the use of small cell technology in the 5th generation mobile communication system can significantly reduce the shadow area and reduce the millimeter wave path loss problem.