• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.21 no.2
• /
• pp.144-150
• /
• 2008

Recently, there has been growing interest in low loss and low dielectric constant material for LTCC application, as the frequency range for electronic devices increases. This study was designed to evaluate the effect of cordierite filler for low dielectric constant LTCC material. From the previous experiments, two glass compositions of B-Si-Al-Zn-Ba-Ca-O and B-Si-Al-Sr-Ca-O system, were chosen. Each powder of two glass compositions was sintered respectively with commercial cordierite powder in temperature range from $800^{\circ}C\;to\;900^{\circ}C$. Crystalline cordierite and glass peaks were affected only with two factors of composition and sintering temperature among various factors. With the optimized condition of two cordierite/glass compositions, obtained dielectric constant was below 5.5 and quality factor was above 1,000. Closed pore of sintered body was controled by sintering temperature and sintering time. When cordierite/glass composite with ratio of 5.5:4.5 was sintered at $900^{\circ}C$, densification was sufficient with good dielectric characteristics of ${\epsilon}_r<5.1,\;Q{\ge}1,000$. Residual fine closed pores could be reduced with control of sintering temperature and time. 3 point bending strength and chemical durability were evaluated to obtain feasibility for substrate material.

• Journal of the Korean institute of surface engineering
• /
• v.45 no.5
• /
• pp.188-192
• /
• 2012

The hetero junction on dielectrics and ferrite for LTCC was prepared by using NiCuZn ferrite. The shrinkage behaviour of ferrite tapes in combination with a dielectric tape was investigated. The characteristics of NiCuZn ferrite were investigated using XRD (X-ray diffractometer), Dilatometer, FE-SEM (Field emission scanning electron microscope), EDS (Energy dispersive spectrometer). NiCuZn ferrite calcined at $700^{\circ}C$ had a good apparent density and initial permeability of magnetic properties. The shrinkage rate of the NCZF700 ferrite and dielectric material was similar. The multilayer revealed dense, uniform morphologies with excellent interface quality. Diffusion of hetero junction such as dielectric and ferrite was not occuring at $900^{\circ}C$.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.36 no.2
• /
• pp.151-157
• /
• 2023

Integrating dielectric materials into LTCC is a convenient method to increase the integration density in electronic circuits. To enable co-firing of the high-k and low-k dielectric LTCC materials in a multi-material hetero-laminate, the shrinkage characteristics of both materials should be similar. Moreover, thermal expansion mismatch between materials during co-firing should be minimized. The alternating stacking of an LTCC with silica filler and that with calcium-zirconate filler was observed to examine the use of the same glass in different LTCCs to minimize the difference in shrinkage and thermal expansion coefficient. For the LTCC of silica filler with a low dielectric constant and that of calcium zirconate filler with a high dielectric constant, the amount of shrinkage was examined through a thermomechanical analysis, and the predicted appropriate fraction of each filler was applied to green sheets by tape casting. The green sheets of different fillers were alternatingly laminated to the thickness of 500 ㎛. As a result of examining the junction, it was observed through SEM that a complete bonding was achieved by constrained sintering in the structure of 'calcium zirconate 50 vol%-silica 30 vol%-calcium zirconate 50 vol%'.

• Proceedings of the International Microelectronics And Packaging Society Conference
• /
• 2000.11a
• /
• pp.57-57
• /
• 2000

Brazing characteristics of the LTCC(Low Temperature Co-fired Ceramics)/ Kovar(Fe-Ni-Co alloy) was investigated. Kovar is one of the typical material for the lid of MCM and packages. In case of alumina package, Brazing process is done by higher temperature profile than 800 $^{\circ}C$ and Ag-Cu alloy. But, LTCC has sintering temperature near 850 $^{\circ}C$. So, it is difficult to use the same process as alumina brazing. The adhesion strength of the brazed part is affected by brazing alloy and metallization properties between conductor pattern and LTCC material. We investigated brazing characteristics of the LTCC/Kovar using various brazing alloys(Ag-Cu, Au-Sn) and process conditions. And, we examined the influence of the glass contents in conductor on the brazing characteristics of the LTCC/Kovar.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2010.06a
• /
• pp.205-205
• /
• 2010

Recently, low temperature co-fired ceramic (LTCC) technology is widely used in sensors, actuators and microsystem fields because of its very good electrical and mechanical properties, high stability as well as possibility of making 3D micro structures. In this study, we investigated the effects of on $O_2$ annealing treatment on the electrical properties of Pb(ZrTi)$O_3$ (PZT) thin films deposited on LTCC substrate. The LTCC substrates with thickness of $400\;{\mu}m$ were fabricated by laminating 4 green tapes which consist of alumina and glass particle in an organic binder. The PZT thin films were deposited on Au / LTCC substrates by RF magnetron sputtering method. The change of the crystallization of the films were investigated under various atmosphere. The structural variation of the films were analyzed by using X-Ray diffraction (XRD) and field emission scanning electron microscopy (FESEM) and secondary ion mass spectrometry (SIMS).

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2001.07a
• /
• pp.676-679
• /
• 2001

A low-temperature cofired-ceramic (LTCC) multi-layer ceramic (MLC) band-pass filter (BPF) is presented, which has the benefits of low cost and small size. The BPF is designed for a IMT-2000 handset. The computer-aided design technology is also presented. The BPF with an attenuation pole at below the passband has been discussed and realized. The equivalent circuit of the BPF was established by transmission lines and lumped capacitors. The frequency characteristics of the LTCC-MLC BPF is well acceptable for IMT-2000 application.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2006.11a
• /
• pp.41-42
• /
• 2006

LTCC 공정의 안정화를 위한 기본적인 공정인 분산의 최적화를 위하여 상용 LTCC 분말인 MLS-22(NEG, Japan)를 이용하여 다양한 평가 방법으로 분산성을 평가하였다. 분산제의 종류와 함량을 조절하여 슬러리의 점도, 표면 거칠기, 코팅된 슬러리의 표면 미세구조를 측정하였다. SN-dispersant 9228 분산제를 사용한 경우 0.4wt%첨가되었을 때 최적의 분산 특성을 얻을 수 있었으며 각 평가 방법은 잘 일치하는 분산의 평가 경향을 나타내었다.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2010.03b
• /
• pp.14-14
• /
• 2010

Recently, low temperature co-fired ceramic (LTCC) technology has gained a remarkable application potential in sensors, actuators and micro systems fields because of its very good electrical and mechanical properties, high reliability and stability as well as possibility of making 3D micro structures. In this study, we investigated the effects of annealing treatment on the electrical properties of $Pb(ZrTi)O_3$ (PZT) thin films deposited on LTCC substrate. PZT thin films were deposited on Au / LTCC substrates by RF magnetron sputtering method. Then, the change of the crystallization of the films were investigated under various annealing temperatures and times. The results showed that the crystallization of the films were enhanced as increasing annealing temperatures. The film, annealed at $700^{\circ}C$, 3min, was well crystallized in the perovskite structure.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2005.11a
• /
• pp.244-245
• /
• 2005

This paper presents the performance of BALUN embedded in the LTCC substrate of ZigBee system which is one of the kind of wireless communication. The BALUN is used to make two signal which have 180$^{\circ}$ phase difference and 3dB power from one input signal. Therefore, this is 3-port network circuit. At the center frequency(915MHz), insertion losses were 3.1dB and 3.4dB, respectively. Also, the phase difference was 182$^{\circ}$. Its size is 2.1$\times$3.6mm. The Used materials were dupont9599 LTCC ceramic and daejuo086 Ag.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2002.05c
• /
• pp.23-26
• /
• 2002

In ceramic systems using LTCC, many components including embedded passives and TRL's are used for composition of 3-dimensional circuit. So the exact analysis on this components must be performed. As for the TRL's, material properties including electrical conductivity of metal, loss factor and effective dielectric constant of dielectric material and geometrical factors like roughness of surface, vias, dimension of TRL structure have a large effect on the characteristics of transmission lines. Such properties of materials have different values in each system with ideal ones presented in text book. In this research, the effective material properties in each system are examined and the effect of material properties and geometrical factors on the characteristics of TRL's are analyzed and quantified by simulation and measurement.