• 한국기계가공학회지
• /
• 제2권4호
• /
• pp.40-45
• /
• 2003

In this paper, to choose the optimum CBN wheel for Internal Grinding at LM Guide, among 7 types of CBN-wheels, the 2 types of CBN-wheels, which were the macrofracture CBN wheel and the microfracture CBN wheel, have been used, and the SCM420H have been used as the workpiece. The working conditions in the grinding experiments were depth-of-cut, table speed, and spindle speed for 4 types of the CBN grinding wheels, 2 types of the lubrications. By the experiments, the loading effect of the microfracture types of the CBN-wheel needed a short dressing interval and resulted in grinding wheel wear and bad surface roughness. However, a macrofracture type of CBN-wheel with the concentration of 100, CB120Q100V showed the best surface roughness quality at a low table speed for internal grinding at LM-guide.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2013년도 춘계학술대회 논문집
• /
• pp.217-218
• /
• 2013

• 대한기계학회논문집A
• /
• 제29권7호
• /
• pp.955-963
• /
• 2005

This research investigates dynamic characteristics of a linear motion (LM) guide through a experimental result and theoretical analysis. The stiffness in the LM guide is determined by the preloading due to the minus clearance between the ball bearing and the contact surface and it can be derived by Hertzian contact theory and the nonlinear motion of equation. The vibration analysis is performed using Lagrange equations and its result agrees with the experiment result. Using the sensitivity analysis on design parameters such as the contact angles of ball bearings and the eccentricity of mass center, the variation of the natural frequencies can be predicted.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2013년도 춘계학술대회 논문집
• /
• pp.121-122
• /
• 2013

• 소성∙가공
• /
• 제24권5호
• /
• pp.340-347
• /
• 2015

Multi-pass shape drawing is used to manufacture long products of arbitrary cross-sectional shapes. This process allows smooth surface finishes and closely controlled dimensions of the cross-sectional shape. Tube shape drawing for hollow type products provides material savings and weight reduction. The intermediate die shapes are very important in multi-pass tube shape drawing. In the current paper, the design method for the intermediate dies in a tube shape drawing process is developed using a die offset for corner filling (DOCF) method. Underfill defects are related to the radial velocity distribution of each divided section in the deformation zone. The developed intermediate die shape design was applied to the two-pass tube shape drawing with fixed mandrel for manufacturing a hollow linear motion (LM) guide rail. The proposed design method led to uniform and steady metal flow at each divided section. FE-simulations and experiments were conducted to validate the effectiveness of the proposed method in multi-pass tube shape drawing process.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2000년도 춘계학술대회 논문집
• /
• pp.692-695
• /
• 2000

This paper is concerned with Accuracy Design of LM Guide System in Machine Tools. Elastic deformation of bearing is calculated by Hertz contact theory and motion error of LM block is analyzed. A new algorithm using block stiffness is proposed fur the analysis of motion accuracy of the table. The best advantage of this algorithm is fast analysis speed because it isn't necessary iteration processes for satisfying equilibrium equation of the table. Motion errors of the table analyzed under artificial form error of rail theoretically and experimentally. Only one of two rails is bent by putting a thickness gauge into horizontal direction. This form error of rail is measured by gap sensor against the other rail. Then, motion errors of the table are predicted by proposed new algorithm theoretically and measured by laser interferometer. Measurements are carried out by changing the preload and thickness. The results show that the table motion errors are reduced from 1/2 to 1/60 times than form error of rail according to its height and width. And the effect of preloading is almost negligible.

• 한국정밀공학회지
• /
• 제29권4호
• /
• pp.409-416
• /
• 2012

Recently, surface modification technology is of importance to improve the wear resistance and the corrosive resistance for high accurate mechanical parts such as LM guide, Ball Screw and Roller Bearing etc., Those has generally featured on rolling contact mechanism to improve not only the wear and the friction, but also the accuracy and the corrosion performances. For surface modifications of high accurate mechanical parts, normally thermal spray, PVD, CVD and E.P. processes have been used with many materials such as DLC, raydent, W, Ni, Ti etc. Diamondlike carbon (DLC) films possess a combination of attractive properties and have been largely employed to modify the tribological behaviors such as friction, wear, corrosion, fretting fatigue, biocompatibility, etc. However, for rolling contact mechanism mechanical parts DLC films are needed to study for commercial benefit. Rolling contact mechanism has features on effects of cyclic motions and stresses, and also not simply sliding motions. The papers focused on the performance test of wear and corrosive resistance according to Me-DLC film thickness. And also, its thickness effect of wear analysis was carried out through the simulation of the maximum shear stress under the rolling contact surface. As the results, Me-DLC films have more potential to improve the wear resistance for high precision mechanical parts than raydent films.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2010년도 춘계학술대회 논문집
• /
• pp.463-464
• /
• 2010

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2010년도 추계학술대회 논문집
• /
• pp.527-528
• /
• 2010

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2011년도 춘계학술대회 논문집
• /
• pp.545-546
• /
• 2011