• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.31 no.10
• /
• pp.21-26
• /
• 2003

In this research, the change of coefficient of thermal expansion (CTE) of graphite/epoxy composite laminate under space environment was measured using fiber optic sensors. Two fiber Bragg grating (FBG) sensors have been adopted for the simultaneous measurement of thermal strain and temperature. Low Earth Orbit (LEO) conditions with high vacuum, ultraviolet and thermal cycling environments were simulated in a thermal vacuum chamber. As a pre-test, a FBG temperature sensor was calibrated and a FBG strain sensor was verified through the comparison with the electric strain gauge (ESG) attached on an aluminun specimen at high and low temperature respectively. The change of the CTE in a composite laminate exposed to space environment was measured for intervals of aging cycles in real time. As a whole, there was no abrupt change of the CTE after 1000 aging cycles. After aging, however, the CTE decreased a Little all over the test temperature range. These changes are caused by outgassing, moisture desorption, matrix cracking etc.

• Aerospace Engineering and Technology
• /
• v.11 no.2
• /
• pp.87-95
• /
• 2012

This technical paper describes the analysis results of telemetry data for the initial activation of star trackers for an agile high accuracy low earth orbit satellite. The satellite was recently launched and is in the Launch and Early Operation Phases. It uses two SED36 star trackers manufactured by SODERN. The star tracker is separated by three parts, an optical head, an electronics box, and a baffle with maintaining optical head base plate temperature 20 degC in order to achieve the better performance in low frequency error. This paper presents the initial activation status, requirements and performance, anomaly occurrence, and noise equivalent angle performance analysis during the mission mode by processing the telemetry data.

• The Bulletin of The Korean Astronomical Society
• /
• v.37 no.2
• /
• pp.163.1-163.1
• /
• 2012

이 연구는 우주물체에 대한 광학감시 및 추적을 수행하기 위한 선행연구로, 궤도전파 시뮬레이터를 개발하여 궤도상 위성의 광학관측가능성을 분석하고 광학관측 여부를 판단하는 것을 목표로 한다. 연구의 주 내용은 주어진 궤도정보를 바탕으로 하는 태양동기궤도(Sun-Synchronous Orbit; SSO) 위성, Dawn-dusk 위성, 저궤도(Low Earth Orbit; LEO) 위성, 정지궤도(Geostationary Orbit; GEO) 위성 등 궤도상 위성의 추정궤도 전파와 자국위성의 광학관측가능성 분석으로 구성된다. 각각의 궤도전파 정밀도 및 광학관측가능성 분석성능을 확인하기 위해 AGI(Analytical Graphics Incorporated)사의 STK(Satellite Tool Kit) 시뮬레이션 프로그램을 사용하여 개발된 궤도전파 시뮬레이터와 비교하였다. 시뮬레이션 과정에서 광학관측의 제한조건을, 지구반영(penumbra)과 태양직사광(direct sun)에서만 관측하며, 고도(elevation angle)의 최소값은 20도, 태양고도(Sun elevation angle)의 최대값은 -10도로 설정하였다. 광학관측이 이루어지는 가상의 관측소는 임의로 선정하였으며, 기본적인 관측시간은 1년으로 잡고, 계절의 변화에 따른 광학관측가능성 궤적의 변화를 보기위해 춘하추동에 대해서 각각 3일이내의 기간 동안 시뮬레이션을 수행하였다. 결과적으로, 우주물체 광학감시 및 추적을 수행하기 위한 광학관측가능성 분석성능은 궤도전파 시뮬레이터 및 초기궤도요소 정밀도, 좌표변환과정 오차 등의 영향을 받으며, 설정된 제한조건에 따라 광학관측 지속시간의 차이가 발생한다. 연구결과를 통해 궤도상 위성의 궤도를 추정하기 위한 위성의 궤도전파 시뮬레이터를 개발하고, 자국위성의 관측가능성 분석을 통해 광학감시 및 추적시스템의 운영이 원활히 이루어질 수 있도록 한다.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.41 no.3
• /
• pp.200-209
• /
• 2013

In this paper, the types of B-dot controller and the review results of B-dot controller stability are summarized. Also, it is confirmed that B-dot controller is very useful and essential tool when a dawn-dusk low earth orbit(LEO) large satellite has especially to capture the Sun for a required power supply in a reliable way after anomaly and that its algorithm is very simple for on-board implementation. New physical interpretation of B-dot controller is presented as a result of extensive theoretical investigation introducing the concept of transient control torque and steady state control torque. Also, the failure effect analysis results of magnetic torquers as well as a simulation verification are included. And the design recommendation for optimal design is provided to cope with the failure of magnetic torquer. Nonlinear simulation results are included to justify its capability as well as its performance for an application to a dawn-dusk LEO large satellite.

• Journal of Environmental Science International
• /
• v.26 no.5
• /
• pp.573-584
• /
• 2017

In order to simulate a typhoon precisely, the satellite observation data has been assimilated using WRF (Weather Research and Forecasting model) three-Dimensional Variational (3DVAR) data assimilation system. The observation data used in 3DVAR was GPS Radio Occultation (GPS-RO) data which is loaded on Low-Earth Orbit (LEO) satellite. The refractivity of Earth is deduced by temperature, pressure, and water vapor. GPS-RO data can be obtained with this refractivity when the satellite passes the limb position with respect to its original orbit. In this paper, two typhoon cases were simulated to examine the characteristics of data assimilation. One had been occurred in the Western Pacific from 16 to 25 October, 2015, and the other had affected Korean Peninsula from 22 to 29 August, 2012. In the simulation results, the typhoon track between background (BGR) and assimilation (3DV) run were significantly different when the track appeared to be rapidly change. The surface wind speed showed large difference for the long forecasting time because the GPS-RO data contained much information in the upper level, and it took a time to impact on the surface wind. Along with the modified typhoon track, the differences in the horizontal distribution of accumulated rain rate was remarkable with the range of -600~500 mm. During 7 days, we estimated the characteristics between daily assimilated simulation (3DV) and initial time assimilation (3DV_7). Because 3DV_7 demonstrated the accurate track of typhoon and its meteorological variables, the differences in two experiments have found to be insignificant. Using observed rain rate data at 79 surface observatories, the statistical analysis has been carried on for the evaluation of quantitative improvement. Although all experiments showed underestimated rain amount because of low model resolution (27 km), the reduced Mean Bias and Root-Mean-Square Error were found to be 2.92 mm and 4.53 mm, respectively.

• Journal of Aerospace System Engineering
• /
• v.17 no.1
• /
• pp.88-96
• /
• 2023

KOMPSAT (Korean Multi-Purpose Satellite) is a Low-Earth-Orbit (LEO) satellite under development in Korea. Its performance has been steadily improving. At this time, power demand of the payload increased according to performance improvement of the payload. Accordingly, design of the satellite, such as design of the internal power supply device and the configuration of the solar array, was changed. Thus, many considerations are required according to an increase in power when designing power EGSE (Electric Ground Support Equipment) for supplying power to satellites and conduct satellite integration tests. This paper deals with matters to be considered when designing power EGSE according to changes in satellite power requirements according to payloads and increase in power requirements.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.44 no.8
• /
• pp.702-709
• /
• 2016

By means of the our satellite development for the past 20 years, it ensure us to obtain domestic independent development capabilities. In the case of practical-class Low-Earth Orbit(LEO) remote sensing satellites, we become a world-class developer. Furthermore, we acquire the technology to develop domestic-leading geostationary satellites, depending on the mission. Currently, we proceed with the next-generation mid-size satellite development program featuring standard bus for the expansion of the world market and has embarked on the development of lunar orbiter from this year.

• Journal of the Institute of Electronics Engineers of Korea SC
• /
• v.47 no.3
• /
• pp.19-27
• /
• 2010

KSLV(Korea Space Launch Vehicle)-I is designed as a launch vehicle to enter a 100 kg-class satellite to the LEO(Low-Earth Orbit). Attitude angles of the upper-stage, including roll, pitch and yaw are controlled by cold gas thruster system using nitrogen gas. The thruster for the KSLV-I is the main pneumatic valve in the RCS(Reaction Control System). In this paper, the design, function tests, and environment tests of the thruster for KSLV-I are described. The developed thrusters are experimentally evaluated and successfully passed the required qualification and acceptance tests.

• Aerospace Engineering and Technology
• /
• v.8 no.2
• /
• pp.122-126
• /
• 2009

KSLV(Korea Space Launch Vehicle)-I is designed as a launch vehicle to enter a 100 kg-class satellite to the LEO(Low-Earth Orbit). Attitude angles of the upper-stage, including roll, pitch and yaw are controlled by cold gas thruster system using nitrogen gas. To verify the flow rate of the gas charging system and to prepare a nitrogen gas charging scenario, the development of a gas charging simulator for RCS(Reaction Control System) is required. This paper describes the orifice design, development, and test of the gas charging simulator for RCS of KSLV-I.

• Aerospace Engineering and Technology
• /
• v.6 no.2
• /
• pp.45-51
• /
• 2007

The various levels of test are performed to verify the correctness, completeness, and quality of the developed flight software. The three main test levels are unit test, integration test and verification test. The flight software unit test is performed on the individual PC environment using target simulator. And integration and verification test is mainly performed on STB(S/W Test Bed) which provides test and debugging environments for flight software on the target board This document is to present the test environment for the next generation low earth orbit satellite flight software development.