• 한국전기전자재료학회논문지
• /
• 제26권8호
• /
• pp.629-634
• /
• 2013

The rectified voltage supplied to LED lamp is used in load and then the surplus voltage can be produced in LED lighting. In this case, LED lighting is proposed that can recyclable the excess voltage to supply power to the controller.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2015년도 제49회 하계 정기학술대회 초록집
• /
• pp.88.1-88.1
• /
• 2015

In recent printed electronics technology, Photo-Sintering, a technique for sintering materials using a light source, has attracted attention as an alternative to time-consuming high-temperature thermal processes. The key principle of this technique is the selective heating of a strongly absorbent thin film, while preventing the heating of the transparent substrate by the light source. Many recent studies have used a flash lamp as the light source, and investigated the material-dependent effect of the width or intensity of the pulsed light. However, the flash lamp for sintering is not suitable for industry yet, because of needing too high power to sinter for a large scale. In energy-saving and large-scale sintering, LED technologies would be very useful in the near future. In this work, we investigated a sintering process for silver nanoparticles using UV-LED array. Silver nanoparticles in ink were inkjet-printed on a $1{\times}1cm$ area of a PET film and photo-sintered by 365 nm UV-LED module. A sheet resistance value as low as $72.6m{\Omega}/sq$ (2.3 - 4.5 times that of bulk silver) was obtained from the UV-LED sintering at 300 mW/cm2 for 50 min.

• 대한전기학회논문지:전기물성ㆍ응용부문C
• /
• 제52권2호
• /
• pp.98-104
• /
• 2003

This paper proposes the design of a multi-color lamp using high brightness RGB LEDs for color variation. Appropriate number of RGB LEDs is so chosen according to the color mixing theory that the overall LEDs represent a color temperature of 6500K. Also, the chosen RGB LEDs are suitably arranged by using an optical design program. The lamp has an internal controller circuit, so it can be directly connected to the existing incandescent lamp socket. It's main body is comprised of two PCB layers. The upper layer contains 44 LEDs and the lower one has a simple microcontroller-based PWM control circuit. The lamp has functions of both ON/OFF control and PWM control, and enables color variation of over 100,000 colors and of more than 10 patterns.

• 한국산학기술학회:학술대회논문집
• /
• 한국산학기술학회 2008년도 추계학술발표논문집
• /
• pp.160-163
• /
• 2008

This study developed selecting equipment for damage of street lamp circuit used by current transform and diode. To develop this system, current check used current transform and indication system used LED device. As faulted, current of street lamp circuit change with fault decivce. This chage of current detected and indicated by selecting equipment

• 한국해양환경ㆍ에너지학회지
• /
• 제10권2호
• /
• pp.93-101
• /
• 2007

오염된 연안 저서환경의 생물학적 정화를 목적으로 발광 다이오드(LED)를 이용하여 저서미세조류 Nitzschia sp.(일본 Hakozaki만에서 분리)의 성장에 미치는 광량과 파장의 영향을 조사하였다. Nitzschia sp.는 청색 LED(450 nm), 황색 LED(590 nm), 적색 LED(650 nm) 및 형광램프(복수파장)에서 배양하였다. 온도 $25^{\circ}C$ 그리고 염분 30 psu에서 배양한 Nitzschia sp.는 청색파장에서 $20\;{\mu}mol\;m^{-2}\;s^{-1}$ 그리고 형광램프는 $40\;{\mu}mol\;m^{-2}\;s^{-1}$에서 최대 상대성장속도를 보였으나, 이보다 높은 광량에서는 광 저해현상이 나타났다. 하지만, 황색 파장과 적색 파장의 최대광량에서 ($350\;{\mu}mol\;m^{-2}\;s^{-1}$) 광 저해현상은 관찰되지 않았다. 광량-성장곡선에서 청색 LED는 ${\mu}=-0.46{\exp}(1-I/6.32)+0.46-0.00043I,\;(r^2=0.98)$, 황색 LED는 ${\mu}=0.42(I+7.87)/(I+58.9),\;(r^2=0.99)$, 적색 LED는 ${\mu}=0.39(I+3.39)/(I+21.6),\;(r^2=0.94)$ 그리고 형광램프는 ${\mu}=-0.38{\exp}(1-I/7.23)+0.38-0.00016I,\;(r^2=0.96)$로 나타났다. 청색 LED, 황색 LED, 적색 LED와 형광램프의 최대성장률은 각각 $0.44\;day^{-1},\;0.42\;day^{-1},\;0.39\;day^{-1}$ 그리고 $0.37\;day^{-1}$이었다. Nitzschia sp.의 최대흡수계수는 472 nm($0.0224\;m^2\;mg\;chi.\;{\alpha}^{-1}$)와 663 nm($0.0179\;m^2\;mg\;chi.\;{\alpha}^{-1}$)에서 보였지만, 모든 파장에서(400 nm-700 nm) 거의 유사한 흡수계수를 보였다. 따라서 가을과 겨울동안에는 청색파장을 조사하여 미세조류 성장을 촉진시키고, 봄과 여름동안에는 황색파장을 조사하여 유해조류의 성장억제와 함께 저서미세조류의 성장시켜 오염된 연안 저서환경 개선에 도움을 줄 수 있을 것으로 생각된다.

• Design & Manufacturing
• /
• 제15권4호
• /
• pp.32-36
• /
• 2021

In this study, the cause of the decrease in transmittance of the outer lens among the causes of the decrease in the amount of light in the automobile headlamp was identified, and the improvement method was selected to determine the effect. The causes of defects that lower the transmittance of the outer lens are divided into a moisture problem and a haze problem. The moisture problem is caused by the temperature difference between the inside and the outside of the head lamp, and the haze problem occurs when the heat inside the head lamp evaporates the haze component contained in the plastic material and attaches it to the outer lens. In order to improve the haze problem that occurs in plastic raw materials, the structures of the bulb light source type headlamp and the LED chip light source type headlamp were analyzed. Among them, the housing material of the LED chip light source type headlamp, which is structurally prone to haze gas, was selected as the test target. In the mass-production injection process of the housing, the drying process was selected as a method to minimize haze gas without adding a separate production process. After extracting a sample every drying time at a constant drying temperature, the sample was put into a haze tester and the residual amount of haze gas was measured. As a result, it was confirmed that the residual amount of Haze gas in the material decreased as the drying time increased.

• 한국조명전기설비학회:학술대회논문집
• /
• 한국조명전기설비학회 2005년도 춘계학술대회논문집
• /
• pp.106-110
• /
• 2005

In this paper, LED traffic signal lamp's operating circuit using Flyback converter and PFC IC has been presented. Most power conversion circuits use PFC IC for Power Factor Correction. The design parameter's value of Flyback converter has been proposed and the error amplifier which regulates the output voltage has been designed Besides, the under voltage protection circuit and the over voltage protection circuit for protecting the operating circuit kin unbalance of common electric power source and the temperature compensation circuit for fixed optical output power have been proposed.

• 전기학회논문지P
• /
• 제63권3호
• /
• pp.178-182
• /
• 2014

This paper investigates the lighting environment of railway system which are mainly used in KTX, Saemaul and Mugunghwa. When lighting used in KTX such as fluorescent lamp and incandescence is being replaced with LED lamp, illumination load of each railroad vehicle has been compared. The comparison result shows that the reduction of power consumption is 43.34% before and after the change. Also it has been performed the economic evaluation.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2007년도 추계학술대회 논문집 전기기기 및 에너지변환시스템부문
• /
• pp.157-159
• /
• 2007

For a vessel to safely navigate on the ocean, it is required to check the vessel position as frequently as possible. When a vessel navigates oil the ocean or entering/leaving a port, the target area such as islands, points and mountain peak, etc. are used. However, when such target are not available or when vessel navigates in night time, installed artificial navigation aid facilities help successful vessel navigation. Light Wave Aid helps to confirm a position to the navigator directly and quickly. So, the synchronous light to display the accurate signal has wide applications. However, lantern domestic industry is small, and most of the products show non-compatibility. Consequently, this paper presents the synchronous lighting using UTC of GPS, which maintains compatibility with different lanterns. Also, by replacing conventional electric bulb with LED lamp, simple and efficient lighting system is obtained.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2003년도 하계학술대회 논문집 C
• /
• pp.1713-1715
• /
• 2003

This paper describes an LED module for a desk lamp using 1[W] high flux while LEDs. The optimum length of the module is obtained from the lighting simulation of the target area of $500{\times}500[mm]$ on the desk, which in turn determines an optimum separation between LEDs. The main issue is to find the optimum separation which gives good illuminance uniformity and high coefficient of utilization at at various reflector structures. Two module configuations of linear and ring types are compared. As a result, good illuminance uniformity is obtained in the case of the ring module. The mofied twin type, however, gives better performance than the ring module, and shows the most performance at an separation angle of around $30^{\circ}$.