• Proceedings of the Korean Vacuum Society Conference
• /
• 2016.02a
• /
• pp.287.1-287.1
• /
• 2016

Three-dimensional (3-D) semiconductor nanoarchitectures, including nano- and micro- rods, pyramids, and disks, are emerging as one of the most promising elements for future optoelectronic devices. Since these 3-D semiconductor nanoarchitectures have many interesting unconventional properties, including the use of large light-emitting surface area and semipolar/nonpolar nano- or micro-facets, numerous studies reported on novel device applications of these 3-D nanoarchitectures. In particular, 3-D nanoarchitecture devices can have noticeably different current spreading characteristics compared with conventional thin film devices, due to their elaborate 3-D geometry. Utilizing this feature in a highly controlled manner, color-tunable light-emitting diodes (LEDs) were demonstrated by controlling the spatial distribution of current density over the multifaceted GaN LEDs. Meanwhile, for the fabrication of high brightness, single color emitting LEDs or laser diodes, uniform and high density of electrical current must be injected into the entire active layers of the nanoarchitecture devices. Here, we report on a new device structure to inject uniform and high density of electrical current through the 3-D semiconductor nanoarchitecture LEDs using metal core inside microtube LEDs. In this work, we report the fabrications and characteristics of metal-cored coaxial $GaN/In_xGa_{1-x}N$ microtube LEDs. For the fabrication of metal-cored microtube LEDs, $GaN/In_xGa_{1-x}N/ZnO$ coaxial microtube LED arrays grown on an n-GaN/c-Al2O3 substrate were lifted-off from the substrate by wet chemical etching of sacrificial ZnO microtubes and $SiO_2$ layer. The chemically lifted-off layer of LEDs were then stamped upside down on another supporting substrates. Subsequently, Ti/Au and indium tin oxide were deposited on the inner shells of microtubes, forming n-type electrodes of the metal-cored LEDs. The device characteristics were investigated measuring electroluminescence and current-voltage characteristic curves and analyzed by computational modeling of current spreading characteristics.

• Journal of Bio-Environment Control
• /
• v.17 no.4
• /
• pp.283-287
• /
• 2008

To investigate the effects of different wavelengths of photosynthetically active radiation on the morphology and leaf color changes of a single tomato (Lycopersicon esculentum) seedling, we stored the seedling at $10{\pm}0.5^{\circ}C$ under eight different wavelengths (peak wavelengths; 405, 450, 505, 545, 600, 645, 680, and 700 nm) with a constant photosynthetic photon flux of $3{\mu}mol\;m^{-2}s^{-l}$ for 28 d. Under the 405, 450, and 505 nm wavelength conditions, the leaves of the seedlings showed vigorous shape with an upright morphology. Rachis elongation was suppressed and hence compact appearance was observed under the 450 and 505 urn conditions. Although the difference in leaf color between before storage and on 28 days after storage was observed under all wavelength conditions, the 405 and 700 um irradiations changed the leaf color to light green. Application of light-emitting diode (LED) light irradiated from around 450 to 545 nm can contribute to vigorous shape with an upright morphology of tomato seedlings during low light irradiation-low temperature storage.

• Journal of computational fluids engineering
• /
• v.18 no.1
• /
• pp.63-68
• /
• 2013

The purpose of this study is to investigate the cooling performance of radial heat sink used for high power LED lightings by natural convection cooling with surrounding air. Experimental and numerical analyses are carried out together. Parametric studies are performed to compare the effects of geometric parameters in radial heat sink such as the number of fins, fin height, fin length, and thickness of fin base as well as the surface coatings of radial heat sink. In this study, the cooling of 60 W LED lamp is examined with radiative heat transfer considered as well as natural convection. Numerical results show the optimum condition when the number of fin is 40, heat sink height is 120 mm, fin length is 15 mm, and fin base thickness is 3 mm. The difference in temperature of the LED metal PCB is within $1^{\circ}C$ between numerical analyses and experimental results. Also, the CNT coating on the heat sink surface is found to increase the cooling performance significantly.

• Proceedings of the KIEE Conference
• /
• 2001.04a
• /
• pp.426-428
• /
• 2001

현재 국내에서 사용되고 있는 신호등용 전구는 전량 해외에서 수입되는 백열전구로써, 낮은 발광효율($8.0{\sim}8.4lm/W$)과 짧은 수명(약 4,000 hours)으로, 지방 자치단체의 경우 전기에너지의 과소비와 과중한 전력요금 부담 잦은 유지보수로 관리비용이 증가하고 교통환경을 악화시키는 원인이 되고 있으며, 국가적으로는 첨두부하 증가, 귀중한 에너지 낭비 및 석유, 가스 등 발전용 화석연료 사용증가에 따른 환경오염을 유발하고 있다. LED(Light Emitting Diode. 발광다이오드)는 발광 특성상 열 발생이 적고, 특정 파장대의 단색광을 발광하는 광원으로써 전력소비가 매우 작고, 긴 수명, 양호한 환경 특성을 가지고 있다. 옥외에 노출되고, 점등이 길고 소등 횟수가 많으며 단색광을 필요로 하는 신호등에 적합한 것으로 평가되고 있다. 그러나 LED 신호등은 발광 원리 및 발광 방식이 기존의 전구식과 달라 현재 규정된 시험방법으로 직접 평가가 불가능하다. 따라서 우리나라의 경우 LED 제조기술은 세계적인 수준이나 LED 신호등에 대한 기술개발 및 보급은 현실적으로 어려운 실정이다. 본 논문에서는 국내 보급환경 구축을 위해 LED 신호등에 대한 시제품의 특성을 장시간의 옥외 시험을 통해 우리나라 환경 특성에 적합한 LED 교통 신호등 규격을 연구하고자 한다.

• Journal of the Korean Association of Oral and Maxillofacial Surgeons
• /
• v.33 no.1
• /
• pp.1-10
• /
• 2007

To verify the inhibitory or protective effects of light-emitting diode(LED) irradiation on apoptotic cell death induced by $CoCl_2$, human SH-SY5Y cells were treated with $CoCl_2$ and LED were used to irradiate the cells. In the cell viability assay, cells were died slowly from $50{\mu}M$ to $250{\mu}M$ and about 50% of cells died after 12 hours at $400{\mu}M$ of $CoCl_2$. The Diff-Quik staining revealed that cells showed condensation of DNA and blebbing of the cell membrane. The DNA fragmentation assay revealed the DNA fragmentation, which is another apoptosis marker, occurred in cells treated with $400{\mu}M$ $CoCl_2$ for 16 hours. In the western blot for HIF-$1{\alpha}$, HIF-$1{\alpha}$ was expressed after 3 hours from induction and peaked maximally at 16 hours. In the cell viability assay of the effects of LED irradiation (at 590 nm for 1 hour 20 minutes), the cells showed more proliferation (about 20%) than the control group. The RPA assay of various apoptosis-related molecules showed that pro-apoptosis molecules such as Bax, Bak, and Bid were upregulated in the $CoCl_2$ treatment group. This means that the apoptotic cell population was increased. However there was some significant changes in LED irradiated cells. In the $CoCl_2$-treated LED irradiation group, those molecules were down-regulated more than in the only $CoCl_2$-treated group. These results have shown that $CoCl_2$ may induce apoptotic cell death in human SH-SY5Y neuroblastoma cells. And LED irradiation has a positive effect on apoptotic cells by down-regulation of pro-apoptotic molecules.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.19 no.1
• /
• pp.91-97
• /
• 2014

Recently, the LED(Light Emitting Diode) is expected to replace conventional lamps including incandescent, halogen and fluorescent lamps for some general illumination application, due to some obvious features such as high luminous efficiency, safety, long life, environment-friendly characteristics and so on. To drive the LED, a single stage PFC(Power Factor Correction) flyback converter has been adopted to satisfy the isolation, PFC and low cost. The conventional flyback LED driver has the serious disadvantage of high 120Hz output current ripple caused by the PFC operation. To overcome this drawback, a new PFC flyback with low 120Hz output current ripple is proposed in this paper. It is composed of 2 power stages, the DCM(Discontinuous Conduction Mode) flyback converter for PFC and BCM(Boundary Conduction Mode) boost converter for tightly regulated LED current. Since the link capacitor is located in the secondary side, its voltage stress is small. Moreover, since the driver is composed of 2 power stages, small output filter and link capacitor can be used. Especially, since the flyback is operated at DCM, the PFC can be automatically obtained and thus, an additional PFC IC is not necessary. Therefore, only one control IC for BCM boost converter is required. To confirm the validity of the proposed converter, theoretical analysis and experimental results from a prototype of 24W LED driver are presented.

• Food Science and Preservation
• /
• v.19 no.3
• /
• pp.354-360
• /
• 2012

The effect of the wavelength of the light emitted by the light-emitting diode (LED) on the growth characteristics and physicochemical and sensory qualities of Pleurotus eryngii were investigated. Pleurotus eryngii were grown under different light sources: blue light (450 nm), red light (650 nm), green light (525 nm), UV-A (365 nm), and mixed light ($B^*R$, $B^*G$, $R^*G$, $B^*R^*G^*UV-A$). The quantity of LED light was set up at 50% (LED: 64.9-108.0 $pmolm-2{\cdot}s-1$;fluorescentlight:11.7lux). Fluorescent light was used as control. There were no significant differences in the flesh firmness. In the case of the Pleurotuseryngii cultivated under red, green, and mixed light ($R^*G$), the color of the pileus and the length of the stipe were similar to those of the control group. The sensory scores were not significantly different between the LED lights (red, green, and $R^*G$) and the control. Among the three LED light conditions, the sample cultivated under red light recorded the highest score. The samples under UV-A, blue, and mixed light ($B^*R$, $B^*G$, $B^*R^*G^*U$) had a dark pileus color and had a short stipe. These results showed that the wavelength of LED light affected the growth and quality characteristics of Pleurotus eryngii, and that using red LED light is preferable for the cultivation of Pleurotus eryngii with better quality.

• Journal of Radiation Protection and Research
• /
• v.43 no.4
• /
• pp.160-169
• /
• 2018

Background: This study aims to develop an integrated optical system that can simultaneously or selectively measure the signals obtained from radioluminescence (RL), thermoluminescence (TL), and optically stimulated luminescence (OSL), which are luminescence phenomena of materials stimulated by radioactivity, heat, and light, respectively. The luminescence mechanism of various materials could be investigated using the glow curves of the luminescence materials. Materials and Methods: RL/TL/OSL integrated measuring system was equipped with a X-ray tube (50 kV, $200{\mu}A$) as an ionizing radiation source to irradiate the sample. The sample substrate was used as a heating source and was also designed to optically stimulate the sample material using various light sources, such as high luminous blue light emitting diode (LED) or laser. The system measured the luminescence intensity versus the amount of irradiation/stimulation on the sample for the purpose of measuring RL, TL and OSL sequentially or by selectively combining them. Optical filters were combined to minimize the interference of the stimulation light in the OSL signal. A long-pass filter (420 nm) was used for 470 nm LED, an ultraviolet-pass filter (260-390 nm) was used for detecting the luminescence of the sample by PM tube. Results and Discussion: The reliability of the system was evaluated using the RL/OSL characteristics of $Al_2O_3:C$ and the RL/TL characteristics of LiF:Mg,Cu,Si, which were used as dosimetry materials. The RL/OSL characteristics of $Al_2O_3:C$ showed relatively linear dose-response characteristics. The glow curve of LiF:Mg,Cu,Si also showed typical RL/OSL characteristics. Conclusion: The reliability of the proposed system was verified by sequentially measuring the RL characteristics of radiation as well as the TL and OSL characteristics by concurrent thermal and optical stimulations. In this study, we developed an integrated measurement system that measures the glow curves of RL/TL/OSL using universal USB-DAQs and the control program.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.31 no.5
• /
• pp.324-329
• /
• 2018

Red phosphor in glasses (PiGs) for automotive light-emitting diode (LED) applications were fabricated with 620-nm $CaAlSiN_3:Eu^{2+}$ phosphor and Pb-free silicate glass. PiGs were synthesized and mounted on high-power blue LED to make a monochromatic red LED. PiGs were simple mixtures of red phosphor and transparent glass powder. After being fabricated with uniaxial press and CIP at 300 MPa for 20 min, the green bodies were thermally treated at $550^{\circ}C$ for 30 min to produce high dense PiGs. As the phosphor content increased, the density of the sintered body decreased and PiGs containing 30% phosphor had a full sintered density. Changes in photoluminescence spectra and color coordination were studied by varying the thickness of plates that were mounted after optical polishing. As a result of the optical spectrum and color coordinates, PiG plate with $210{\mu}m$ thickness showed a color purity of 99.7%. In order to evaluate the thermal stability, the thermal quenching characteristics were measured at temperatures of $30{\sim}150^{\circ}C$. The results showed that the red PIG plates were 30% more thermally stable compared to the AlGaInP red chip.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.15 no.1
• /
• pp.245-251
• /
• 2015

In this paper, we present a design of PWM-controlled driving device for backlights in LED systems. The system can control either the brightness of the entire screen of backlights of LCD driven by LED or illumination or contrast of each partial segment of the entire screen. The PWM-controlled driving device includes the shift register that shifts the series data according to the clock signal prior to the generation of parallel data. It is also is comprised of a number of registers, a number of counters, a number of comparators, and a number of synchronizing gates (producing the PWM-controlled signals). The proposed device for backlights in LED systems can generate the PWM-controlled signal with a high degree of resolution without the increase of clock frequency. It also contains the PWM-controlled circuit that disperses and restrains the quantized noise.