• Journal of Life Science
• /
• v.27 no.7
• /
• pp.754-759
• /
• 2017

The 100 l culture system was made on the basis of LED light, and Nannochloropsis oculata was cultured in f/2 medium at light intensity ($100{\mu}mol/m^2/s$), culture temperature ($20^{\circ}C{\pm}1^{\circ}C$) and LD cycle (12hr). As a result, the maximum biomass of 1.07 g/l was cultured as a result of 100 l mass culture at $100{\mu}mol/m^2/s$ and 24 mg/l nitrate concentration in LED blue (475 nm). The extraction was carried out using sonicator, homogenizer and chemical method 0.5M HCl shredding method. The contents of chlorophyll a, chlorophyll b and carotenoid were 1.6, 0.5 and 0.3 mg/g cell. When using homogenizer, it was measured at 1.0, 0.6 and 0.2 mg/g cell. The chemical breakdown method of 0.5M HCl, chlorophyll a, b, and carotenoid contents were measured as 0.9, 0.8, 0 mg/g cell. The highest amount of biomass during the distruption time was measured at 3.6 mg/g cell at 15 min disintegration and acetone, 3.6 mg/g cell of acetone, methanol, and ethanol were measured as effective solvents. Concentration was measured by using microfilter, disk type continuous centrifuge and tubular type continuous centrifuge were 16.0, 1.1 and 0.5 g/l, respectively. Four kinds of equipment such as hot air dryer, vacuum dryer, spray dryer and freeze dryer were tested to optimize the drying process. As a result, the recovery rates of spray dryer and freeze dryer were 80% and 60%.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.22 no.1
• /
• pp.11-14
• /
• 2012

The AlGaN layer has direct wide bandgaps ranging from 3.4 to 6.2 eV. Nowadays, it is becoming more important to fabricate optical devices in an UV region for the many applications. The high quality AlGaN layer is necessary to establish the UV optical devices. However, the growth of AlGaN layer on GaN layer is difficult due to the lattice mismatch and difference thermal expansion coefficient between GaN layer and AlGaN layer. In this paper, we attempted to grow the LED structure on GaN template by mixed-source HVPE method with multi-sliding boat system. We tried to find the optical and lattice transition of active layer by control the Al content in mixed-source. For the growth of epi layer, the HCl and $NH_3$ gas were flowed over the mixed-source and the carrier gas was $N_2$. The temperature of source zone and growth zone was stabled at 900 and $1090^{\circ}C$, respectively. After the growth, we performed the x-ray diffraction (XRD) and electro luminescence (EL) measurement.

• Journal of Climate Change Research
• /
• v.4 no.3
• /
• pp.211-219
• /
• 2013

This study uses the LEAP model that is a long-term energy analysis model to analyze reduction potential on S city residential sector energy usage for greenhouse gas emission. Energy consumption of S-si in 2009 is consumed most in residential and commerce sector by 39.1%. Also, energy and greenhouse gas emission of residential sector is expected to increase due to increase of households. Therefore, greenhouse gas reduction measures are desperately required in residential sector. For this study recognizes energy consumption of S-si residential sector and has established reduction measure of S-si residential sector greenhouse gas through literature search on domestic and foreign climate change correspondence policies. Also, construction of greenhouse gas reduction potential by reduction measures through LEAP model. There were a total of 5 reduction measures scenarios is Reference Scenario, LED Lighting, Energy Alternative, Green Life Practice, and Total Reduction Measure. As a result, greenhouse gas emission of Light Emitting Diode Lightings by 2020 was $1,181.0thousand\;tonCO_2eq$, decrease of 6.1% compared to the Reference Scenario and Greenhouse gas emission of Energy Alternative by 2020 was $1,171.6thousand\;tonCO_2eq$, decrease of 6.8% compared to the Reference Scenario. Greenhouse gas emission of Green Life Practice by 2020 was $1,128.7thousand\;tonCO_2eq$, decrease of 10.2% compared to the Reference Scenario. For Total Reduction Measures by 2020 emission was $966.9thousand\;tonCO_2eq$, decrease 23.1% compared to Reference Scenario.

• Journal of the korean academy of Pediatric Dentistry
• /
• v.47 no.2
• /
• pp.120-127
• /
• 2020

The aim of this study was to evaluate the antimicrobial effect of photodynamic therapy (PDT) using plaque disclosing agent, 10 - 20 mM erythrosine, as a photosensitizer. Multispecies cariogenic biofilms containing Streptococcus mutans, Lactobacillus casei and Candida albicans were formed on hydroxyapatite disc. 20 μM, 10 mM and 20 mM erythrosine were applied as a photosensitizer for 3 minutes, and then light-emitting diode (LED) irradiated for 24 seconds. Colony-forming unit (CFU) were measured and biofilms were observed using confocal laser scanning microscopy (CLSM). CFU were significantly decreased in the PDT groups using 10 - 20 mM erythrosine (10 mM, 20mM) and the results were also confirmed by CLSM. This study confirms the high antimicrobial effect of photodynamic therapy using plaque disclosing agent as a photosensitizer.

• Journal of Food Hygiene and Safety
• /
• v.35 no.3
• /
• pp.205-212
• /
• 2020

Foodborne diseases occur frequently and have various being related to the intake of contaminated foods. Seafood products are susceptible to contamination due to higher water content and microorganisms, which combine to give them a short shelf-life. Various approaches have been applied to overcome this problem. Edible coatings that are also biodegradable and biocompatible have been discussed as one of the applicable solutions. These coatings can actually help to maintain seafood quality by inhibiting the growth of microorganisms and delaying the loss of moisture. This paper presents the effects of various natural bio-polymers, antimicrobial substances and physical sterilization techniques such as gamma irradiation, ultraviolet (UV) sterilization, and light-emitting diode (LED) sterilization on seafood coatings.

• Tribology and Lubricants
• /
• v.33 no.3
• /
• pp.106-111
• /
• 2017

Sapphire is an anisotropic material with excellent physical and chemical properties and is used as a substrate material in various fields such as LED (light emitting diode), power semiconductor, superconductor, sensor, and optical devices. Sapphire is processed into the final substrate through multi-wire saw, double-side lapping, heat treatment, diamond mechanical polishing, and chemical mechanical polishing. Among these, chemical mechanical polishing is the key process that determines the final surface quality of the substrate. Recent studies have reported that the material removal characteristics during chemical mechanical polishing changes according to the crystal orientations, however, detailed analysis of this phenomenon has not reported. In this work, we carried out chemical mechanical polishing of C(0001), R($1{\bar{1}}02$), and A($11{\bar{2}}0$) substrates with different sapphire crystal planes, and analyzed the effect of crystal orientation on the material removal characteristics and their correlations. We measured the material removal rate and frictional force to determine the material removal phenomenon, and performed nano-indentation to evaluate the material characteristics before and after the reaction. Our findings show that the material removal rate and frictional force depend on the crystal orientation, and the chemical reaction between the sapphire substrate and the slurry accelerates the material removal rate during chemical mechanical polishing.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2013.02a
• /
• pp.418-419
• /
• 2013

현재, 인듐 주석 산화물(indium tin oxide, ITO) 박막은 가시영역에서 전기적 특성 및 광학적 특성이 우수하기 때문에 평면 디스플레이(flat displays), 박막 트랜지스터(thin film transistors), 태양전지(solar cells) 등을 포함한 광소자에 투명전도성산화물(transparent conducting oxide, TCO) 전극으로 가장 일반적으로 사용되고 있다. 하지만, 이 물질은 밴드갭이 3.4 eV로 다소 작아 다양한 분야의 의료기기, 환경 보호에 응용 가능한 자외선 영역에서 상당히 많은 양의 광흡수가 발생하는 치명적인 문제점을 가지고 있다. 또한, 인듐(Indium)의 급속한 소비는 인듐의 매장량의 한계로 인해 가격을 상승시키는 주요한 원인으로 작용하고 있다. 한편, InGaN 기반의 자외선 발광다이오드 분야에서는 팔라듐(Pd) 기반의 반투명 전극과 은(Ag) 기반의 반사전극을 주로 사용하고 있지만, 낮은 투과도와 낮은 굴절률을 때문에 여전히 자외선 발광다이오드의 광추출 효율(extraction efficiency)에 문제점을 가지고 있다. 따라서 자외선 발광다이오드의 외부양자 효율(external quantum efficiency, EQE)을 높이기 위해 높은 투과도와 GaN와 유사한 굴절률을 가지는 p-형 오믹 전극을 개발해야 한다. 본 연구에서는 초박막의 ITO (16 nm)/Ag (7 nm)/ITO (16 nm) 다층 구조를 갖는 투명전도성 전극을 제작한 후, 열처리 온도에 따른 전기, 광학적 특성에 향상에 대해서 조사하였다. 사용된 산화물/금속/산화물 전극의 구조는 유기발광 다이오드(organic light emitting diode, OLED), 태양전지 등에 많이 사용되는 안정적인 투명 전극을 자외선 LED 소자에 처음 적용하여, ITO의 전체 사용량은 줄이고, ITO 사이에 금속을 삽임함으로써 금속에 의한 전기적 특성 향상과 플라즈몬 효과에 의한 투과도를 높일 수 있는 장점을 가지고 있다. 실험 결과로는, $400^{\circ}C$에서 열처리한 ITO/Ag/ITO 다층 구조는 365 nm에서 84%의 광학적 특성과 9.644 omh/sq의 전기적 특성을 확인하였다. 실험 결과로부터 좀 더 최적화를 수행하면, ITO/Ag/ITO 다층 구조는 자외선 발광다이오드의 투명전도성 전극으로 사용될 수 있을 것이라 기대된다.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.38 no.5
• /
• pp.381-388
• /
• 2014

Our aim was to simulate ocean waves in a small-size wave flume and observe the motion of a cylindrical floating body placed in an offshore environment. To precisely visualize the oscillation of the body, a set of light-emitting diode illuminators and high-speed charge-coupled device camera were installed in the flume. Spectral analysis was performed of the movement of the floating body. The wave generator and absorbers worked well to simulate stable regular waves. As the period of the oncoming waves changed, the movement of the floating body substantially differed when tethered to a tension-leg mooring cable. In particular, when connected to the tension-leg mooring cable, the natural frequency of the floating body suddenly appeared at 0.391 Hz as the wave period was increased.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2005.11a
• /
• pp.309-310
• /
• 2005

In the fabrication of high performance red organic light emitting diode, 2-TNA TA [4,4',4" -tris (2-naphthylphenyl- phenylamino)-triphenylamine] as hole injection material and N PH [N,N'-bis (1-naphthyl) -N,N' -diphenyl-1, 1'-biphenyl-4,4'- diamine] as hole transport material were deposited on the ITO (indium tin oxide)/glass substrate by vacuum evaporation, And then, red color emission layer was deposited using Alq3 as a host material and Rubrene (5,6,11,12- tetraphenylnaphthacene) and GDI 4234 as dopants. Finally, small molecular weight OLED with the structure of ITO/2-TNATA/ NPB/Alq3+Rubrene+GDI4234/Alq3/LiF/Al was obtained by in-situ deposition of Alq3, LiF and Al as electron transport material, electron injection material and cathode. respectively. Green OLED fabricated in our experiments showed the color coordinate of CIE(0.65,0.35) and the maximum luminescence efficiency of 2.1 lm/W at 7 V with the peak emission wavelength of 632 nm.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2010.08a
• /
• pp.256-256
• /
• 2010

투명전극부터 디스플레이 산업에 이르기까지 광범위하게 응용되어지고 있고 개발되어지고 있는 투명전도산화물(TCO)은 ZnO, In2O3, SnO2 등을 기본으로 하는 n-type 재료가 대부분이다. 그러나 투명전도 산화물을 이용한 light emitting diode(LED), 투명한 태양전지, p-형 TFT와 같은 투명전자소자의 개발을 위해서는 p-type 소재가 필수적이다. p-type TCO 소재는 비교적 연구 개발 실적이 매우 부진한 실정이었다. 1997년 넓은 밴드갭을 가지는 ABO2(delafossite) 산화물이 p-type으로서 안정적이라는 것을 보고함에 따라 이에 대한 연구가 활발히 진행되고 있다. 현재 ABO2 형태를 가진 Delafossite구조 산화물이 가장 유망한 p-type 투명전도체 소재로 거론되고 있다. Delafossite 구조가 p-type 투명전도체에 적합한 결정구조인 이유는 밴드갭이 넓고 공유결합에 유리하기 때문이다. Delafossite구조는 상온에서 2종류의 polytype(상온에서 Rhombohedaral구조와 hexagonal 구조)이 존재하며 이들은 각각 3R 및 2H의 결정 구조를 가지고 있다. ABO2의 delafossite구조에서 Cu+의 배열은 c-축을 따라 Cu-O-Cr-O-Cu의 연속적인 층 구조로서 2차원연결로 보여 진다. 보고된 Cu- base delafossite구조를 가지는 재료들은 CuAlO2, CuGaO2, CuInO2 등 여러가지가 있다. 본 연구에서는 PLD를 이용하여 c-plane 사파이어 기판위에 성장된 delafossite구조인 CuCrO2박막의 특성을 알아보았다. p-type 특성을 위하여 CuCrO2에 Zn를 첨가하였으며 그에 따른 구조적 전기적 특성을 조사하였다. 성장온도와 산소분압을 $500{\sim}700^{\circ}C$, 0~10mTorr로 변화시켜 특성을 연구하였다. 성장온도 $700^{\circ}C$, 산소분압 10mTorr에서 c-plane 사파이어 기판위에 c-축 배향의 에피성장된 CuCrO2:Zn 박막을 얻을 수 있었다. Mg를 도핑함에 따른 p-type 특성보다 현저히 떨어지는 것을 확인하였다. 또한 동일한 조건임에도 특정한 이차상의 존재를 통해 도핑된 Zn의 위치를 추측할 수 있었다. 온도와 분압에 따른 결정성과 표면상태를 SEM을 통해서 확인하였다.