• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.29 no.3A
• /
• pp.303-310
• /
• 2004

In this paper, L-shaped slot antenna for 5.15㎓-5.35㎓ is designed, fabricated. and measured. The prototype consist of four L-shaped slot. To obtain suitable bandwidth, the form layer is inserted between ground plane and substrate. Important parameters in the design are four L-slot length. width, position, air-gap height. and feed Point position. From these parameters optimized, a four L-shaped slot antenna is fabricated and measured. The measured results of the antenna are obtained as follows results. The resonant frequency of the fabrication four L-shaped slot antenna is 5.25㎓, bandwidth for approximately 5％(VSWR＜1.5) and the gain is 8-9㏈i. The experimental far-field patterns are stable across the pass band. The 3dB bandwidth in H-Plane and I-Plane are 69$^{\circ}$and 62$^{\circ}$, respectively.

• Journal of electromagnetic engineering and science
• /
• v.17 no.2
• /
• pp.57-64
• /
• 2017

In this paper, an asymmetric compact multiband slot antenna is proposed for global positioning system (GPS), worldwide interoperability for microwave access (WiMAX), and wireless area network (WLAN) applications. The top plane, a ground is composed of a rectangular slot with a trapezoidal-like stub, an inverted U-shaped slot at the right side of the rectangular slot, an inverted L-shaped slot at the left side of the rectangular slot, and three stubs. The proposed antenna is fed by an asymmetric cross-parasitic strip on the bottom plane. By properly designing the slots and stubs, four resonant frequency bands are achieved with -10 dB reflection coefficient bandwidths of 50 MHz, 400 MHz, 390 MHz, and 830 MHz in the 1.57 GHz GPS band, 2.4 GHz WLAN band, 3.5 GHz WiMAX band, and 5.5 GHz WLAN bands, respectively. The antenna has a total compact size of $13mm{\times}32mm{\times}0.8mm$. Simulated and measured results indicate that the proposed antenna has sufficient bandwidth and good radiation performance in each band.

• The Journal of the Korea Contents Association
• /
• v.8 no.5
• /
• pp.52-60
• /
• 2008

A simple Time Division Multiplex(TDM) switching system which has been widely in satellite networks provides any size of bandwidth for a number of low bandwidth subscribers by allocating proper number of time slots in a frame. In this paper, we propose a new approach based on graph coloring model for efficient time slot assignment algorithm in contrast to network flow model in previous works. When the frame length of an initial matrix of time slot requests is 2's power, this matrix is divided into two matrices of time slot requests using binary divide and conquer method based on the graph coloring model. This process is continued until resulting matrices of time slot requests are of length one. While the most efficient algorithm proposed in the literature has time complexity of $O(N^{4.5})$, the time complexity of the proposed algorithm is $O(NLlog_2L)$, where N is the number of input/output links and L is the number of time slot alloted to each link in the frame.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.16 no.4
• /
• pp.599-604
• /
• 2021

In the information age, internet was developed from the wired access to the wireless Internet access. When a surge in demand for wireless Internet access, efficiency and performance of 2.4 and 5GHz band which leads to saturation of the communication was significantly fall. In this paper, we studied the design and fabrication of slot patch antenna to be used in wireless communication systems operating at around 10GHz band. To obtain optimal antenna parameters such as patch size, inter patch space, sL, sW, feed L, feed w, slot patch antenna was simulated by HFSS(High Frequency Structure Simulator). From these parameters, slot and patch antenna is fabricated using FR-4 substrate of dielectric constant 4.4. The characteristics of fabricated antenna were analyzed by network analyzer. The fabricated slot patch antenna showed a center frequency as 10.23GHz, the minimum return loss as -32dB, and -10dB bandwidth as 420MHz respectively.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.13 no.7
• /
• pp.732-739
• /
• 2002

Performance of the applicator for hyperthermia is determined by both the degree of impedance matching and specific absorption rate(SAR) distribution in the surrounding tissue. In this paper, the coaxial-slot antenna using staircasing approximation in the FDTD is analyzed and the coaxial-slot antenna for the hyperthermia improving heating characteristics is designed. The SAR of the coaxial-slot antenna approximated to staircasing and square model is analyzed, and the SAR of staircasing model is compared with Saito's SAR measurement and square model. As a result, the SAR of proposed model exhibited agreement with the Saito's measurement of square model. Ig averaged SAR on the liver caused by proposed antenna in this paper is 195 W/kg, and is about 27.9 % higher than the Saito's antenna 152.5 W/kg, respectively.

• Journal of Advanced Navigation Technology
• /
• v.10 no.4
• /
• pp.342-347
• /
• 2006

In this paper, we have designed 800[MHz] broad band antenna that is improves a narrow bandwidth problem of microstrip antenna and it will be able to integrate GSM, TRS band including the CDMA band. It had L-shaped feeding structure and added the U-slot it used a duplex resonance effect. Also for the improvement of profit the stack it did with the perpendicular. It seems to be good quality that design and manufactured antenna frequency bandwidth(VSWR 2:1) is 789~1086[MHz] with 297[MHz](33%). Also the E-plan and H-plan all profit 9.4[dBi] above, 3[dB] beam width was visible the quality which above $61^{\circ}$ is improved.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.24 no.5
• /
• pp.484-491
• /
• 2013

In this paper, the method of designing a wideband antenna has been introduced through the design technique that simultaneously employs L- and slot-type feeds. Using the two kinds of feeds and additional fence structure, a compact wideband patch antenna has been realized. The size of the patch has been reduced by about 30 % based on the low frequency(824 MHz) and the full fractional bandwidth is wider than 100 %. The L-feed element is for the EM coupling feeding at the low frequency, while it functions as a feeding line for the power coupling through the slot at the high frequency. The proposed antenna has been designed not only for wideband operations but also for a proper array element with a reduced size. Thus, the foundation for developing the ultra wideband patch array antennas has been prepared. The fabricated antenna has been found to have good characteristics on V.S.W.R and the radiation patterns over the full bands. The experimental and computed results are shown to be in good agreement.

• Journal of Korean Society of Occupational and Environmental Hygiene
• /
• v.3 no.2
• /
• pp.204-212
• /
• 1993

This study was conducted to evaluate ventilation efficiency of 4-stage slot hood by variation of slot width, flow rate, hood size and baffle size. The slot velocity, control velocity and plenum velocity were related to slot width and the distance between source of contamination and hood. The results obtained from laboratory experiment for local exhaust ventilation systems were as follows ; 1. When slot widths were constant(equally changed) and the velocity was 6-10 m/s, the slot velocity from 1st slot to 4th slot gradually decreased. As the slot width-to-slot length ratio(WLR) decreased, the slot velocity of each stage increased. But if WLR value was less than 0.04, the slot velocity decreased. 2. When slot velocity exceeded 10 m/s with constant slot widths, the slot velocity of each stage was uniform. 3. When the slot velocity was uniform within 10 m/s and the first slot width was 14-20 mm, the slot width ratio between 1st slot and each of three other slots were 1, 1.25, 1.5 and 3.0, respectively. 4. The slot and plenum velocity were uniform when exhaust flow rate changed from 14 to $19m^3/min$ and there were no hood splitter vanes. 5. When the slot velocity at each stage was uniform, the control velocity at site 30 cm away from hood No.2 increased from 0.15-0.30 to 0.25-0.45 m/s and the control distance from 20 to 30 cm(about 1.5 times).

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2016.05a
• /
• pp.630-632
• /
• 2016

In this paper, we propose a modified rhombus slot UWB(Ultra Wide Band) antenna with fork-shaped feeding structure. The proposed modified rhombus slot structure is eliminated upper and lower part of the basic rhombus slot shape to get ultra-wideband characteristics for UWB communication. Also, feeding structure is used to fork-shaped structure to get ultra-wideband characteristics. The antenna is designed on an FR-4 substrate of which the dielectric constant is 4.4, and its overall size is $34mm(W1){\times}34mm(L1){\times}1mm(t)$, and its slot antenna size is $30mm(W2){\times}16.75mm(L3+L4)$. After the optimized process, the proposed antenna is fabricated and measured. Measured result. fabricated antenna satisfied -10 dB impedance bandwidth in UWB frequency band (3.1 ~ 10.6 GHz ). And measured results of gain and radiation patterns characteristics displayed determined for operating bands.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.21 no.1
• /
• pp.107-114
• /
• 2021

In this paper, a planar transistor oscillator for X-band using a newly proposed L-shaped monopole slot resonator is proposed. For planar design, an L-shaped monopole slot with an open-end is used as a resonator for a transistor oscillator. As a result of the simulated design of the resonator in three stages, a high Q value of 1169.84 and a high insertion loss of 49.934 dB were identified. The results of the final design and manufactured oscillator measurements confirmed that the oscillation output is greater than 7 dBm and has good phase noise characteristics of -58 dBc/Hz at 100 kHz offset. The proposed oscillator is planar and has the advantage of being directly applicable to microwave integrated circuit technology. It also has the advantage of being able to reduce its size as it can only be implemented in microstrip form without additional devices such as metal cavities and tuning screws in 3D structures, as in the case of a DRO (dielectric resonance oscillator).