• 대한기계학회논문집B
• /
• 제41권8호
• /
• pp.537-544
• /
• 2017

본 연구의 목적은 수분회수 냉각탑에 설치된 엇갈림(staggered) 형태로 배치된 중공사막 모듈을 다공성 매질(porous medium)로 모델링 시 유동특성을 수치 해석적으로 검토하는 것이다. 1단으로 설치된 중공사막 모듈의 차압 데이터를 이용하여 다공성 매질의 모델링을 위한 압력-속도 2차 식을 도출하였다. 중공사막 모듈을 다공성 매질로 모델링한 경우 ("다공성 매질")와 중공사막 모듈의 형상을 그대로 고려한 경우 ("멤브레인 모듈")에 대해 유동 특성을 비교하였다. "다공성 매질"의 경우 "멤브레인 모듈"에 비해 유동에 의한 압력 변화는 0.6 % 미만의 적은 차이를 나타냈으나, 최대 유속은 약 2.5배, 평균 난류 운동에너지는 95배로 크게 나타났다. 이를 통해 다공성 매질로의 모델링은 압력강하는 잘 구현하나, 유속 및 난류 운동에너지는 잘 모사하지 못함을 알 수 있었다.

• 대한물리치료과학회지
• /
• 제10권2호
• /
• pp.7-16
• /
• 2003

The purpose of this study was to investigate the effect of Treadmill Training with FES(TTF) on walking velocity, gait endurance, and energy expenditure index(EEI) of hemiplegia patients with foot drop. Two subjects with hemiplegia participated in this study. They took walking excercise 5 times per week for 8 weeks. One time excercise spent 30minutes. The theraputic effect was evaluated by how many seconds they needed to walk 10 meters, how far they could walk for 12 minutes, and how much they spent energy in walking for 12 minutes. Two cases were examined before, after 4 week, and after 8 week, walking training. The results of this study are as follows; 1) Walking velocity : Case 1 increased from 0.52m/sec before walking training to 0.83m/sec after 8 weeks. Case 2 increased from 0.58m/sec to 0.92m/sec. 2) Gait endurance : Case 1 increased from 383.23m to 625.53m. Case 2 increased from 410.19m to 693.47m. 3) EEI : For comfortable walking condition, Case 1 decreased from 0.98beats/min to 0.71beats/min, and Case 2 decreased from 0.93beats/min to 0.68beats/min. For maximum walking condition, Case 1 decreased from 0.93beats/min to 0.67beats/min, and Case 2 decreased from 0.91beats/min to 0.61beats/min. The findings suggest that hemiplegia patients can improve their walking velocity, gait endurance and energy expenditure index through TTF.

• 한국안전학회지
• /
• 제29권2호
• /
• pp.12-17
• /
• 2014

This paper is aimed to analyze the characteristics of simultaneous voltage, current and temperature signals for poor connection on electrical connector. In order to attain this purpose, detected were the current and voltage signals on electric wire with series arc, named arc signals, and also monitored were the changes of RMS, instantaneous value of waveform in time domain and temperature value with video. Two states are made normal state over $5kgf{\cdot}cm$ and poor connections state below $0.5kgf{\cdot}cm$ by screw gage. In the voltage signal case, the voltage drop was increased with which the current was increased. In the current signal case, poor connections at the time interval 1~4A all showed "shoulder", as distinct difference from the normal state shown waveform pattern. In the temperature signal case, poor connections are twice at 1A and five times at 4A in the normal state. The temperature continues insulation of electrical wiring and connector can be carbonized. The results of this study will be effectively used in developing the preventive devices and system for electric fire by poor connections.

• 한국공간구조학회논문집
• /
• 제3권2호
• /
• pp.69-75
• /
• 2003

In case of rectangular lattice dome which shearing rigidity is very small, it has a concern to drop Buckling strength considerably by external force. So, by means of system to increase buckling-strength, there is a method of construction that lattice of dome is one with roof material. In a case like this, shearing rigidity of roof material increases buckling-strength of the whole of structure and can be designed economically from the viewpoint of practice. In case of analysis is achieved considering roof material that adheres to lattice of dame, there is method that considers the rigidity that use effective width frame as method to evaluate rigidity of roof material. therefore, this study is aimed at deciding effective width of roof material united with rectangular lattice dome to evaluate rigidity of roof material by effective width of frame and investigating how much does rigidity of roof material united with lattice of dome increase buckling-strength of the whole of structure according to rise-ratio. Conditions of loading are vertical-type-uniform loading. Analysis method is based on FEM dealing with the geometrically nonlinear deflection problems.

• 대한의용생체공학회:의공학회지
• /
• 제21권3호
• /
• pp.311-320
• /
• 2000

본 연구에서는 새롭게 설계한 인공폐 모듈을 사용하여 인공폐의 효율을 평가하기 위한 압력손실과 산소전달에 대한 실험을 수행하였다. 또한 증류수, 아황산나트륨용액을 혈액대용물질로 사용하여 다른 인공폐의 성능을 평가하였다. 혈액대용물질은 압력손실과 산소운반력을 연구하는데 전혈(whole blood)에 비해 장점이 많다 즉. 이들은 상대적으로 값이 저렴하고 조절하여야 할 변수가 적다. 또한 이 용액을 사용하게 되면 탈산화장치가 필요 없으며 실험결과의 분석이 상대적으로 쉽다. 전혈과 같은 산소분압을 갖는 아황산나트륨용액을 사용하는 경우 아황산나트륨 용액의 산소전달속도는 전혈을 사용하는 경우의 산소전달속도와 거의 일치하였다. 이 실험에서 중공사모듈의 산소전달속도를 측정하는데 아황산나트륨용액이 혈액대용물질로 이용될 수 있음을 보였다. 이 인공폐 모듈에서는 용액이 중공사의 바깥쪽으로 흐르도록 설계하였는데 이 실험용 인공폐는 압력손실이 안쪽으로 흐르도록 하는 흐름에 비해 $1/3\~1/6$였다.

• 대한기계학회논문집B
• /
• 제39권3호
• /
• pp.223-229
• /
• 2015

배플과 관군간의 누설유동이 쉘-관 열교환기 성능에 미치는 영향을 FLUENT 를 사용하여 조사하였다. 쉘측 출구온도를 최대로 하는 최적누설유동을 찾기 위해 쉘측 단면적에 대한 누설단면적 비가 0%-40% 범위의 5 가지 누설유동을 가진 쉘-관 열교환기에 대하여 CFD 모델이 개발되었다. 관 입구 및 벽면온도를 일정하게 유지하고 Reynolds 수를 4952 부터 14858 증가시키면서 유동장 및 온도장을 계산하였다. 해석결과, 출구온도, 압력강하, 열전달률은 Reynolds 수뿐만 아니라 누설유동에도 크게 영향을 받는 것으로 나타났다. 누설유동은 열전달률과 압력강하를 동시에 낮추는 결과를 제시한 기존의 결과와는 달리, 본 연구에서는 적정의 누설유동은 배플 주위의 재순환영역에 추가적인 모멘텀을 공급함으로써 최대출구온도, 작은 압력강하, 높은 열전달률을 유도하는 효과를 발휘하는 새로운 결과를 얻었다. 20%의 누설단면적이 최적의 누설단면적으로 나타났다.

• 한국통신학회논문지
• /
• 제28권5B호
• /
• pp.475-488
• /
• 2003

모바일 IP 프로토콜에서 핸드오프 동안에 발생하는 패킷 손실 때문에 초래되는 TCP의 성능저하를 방지하기 위해서는 모바일 IP 경로 최적화 확장의 스무스 핸드오프 방식에서 이전기지국이 핸드오프 동안 손실되는 패킷들을 버퍼에 저장하고 저장된 패킷들이 이동한 단말에게 전달되어야 한다. 그러나 무선링크가 병목인 일반적인 경우에서 이동단말이 새로운 서브 네트워크의 혼잡한 기지국으로 이동한 경우에는, 이전 기지국이 포워딩하는 패킷들은 손실되고 또한 이전 기지국이 포워딩하는 패킷들의 버스트한 도착 특성으로 인해 심화된 혼잡으로 기지국 내 이동단말 플로들의 TCP 전송 성능이 저하되게 된다. 본 논문에서는 기지국 패킷 버퍼링 방식이 결합된 스무스 핸드오프 방식으로 이동단말이 새로운 서브네트워크의 혼잡한 기지국으로 이동한 경우, 기지국 패킷 버퍼링 방식이 혼잡한 기지국을 통과하는 TCP 플로들에게 미치는 영향을 혼잡한 기지국에서의 핸드오프 도착분포에 따라 Drop-Tail과 RED 버퍼관리방식에 대하여 분석하였다. 시뮬레이션 결과는 RED 방식이 Drop-Tail 방식보다 기지국 패킷 버퍼링 방식이 혼잡한 기지국을 통과하는 TCP 플로들에게 가하는 혼잡을 완화할 수 있으나, 이전 기지국이 포워딩하는 패킷들의 버스트한 도착특성으로 인한 Global Synchronization은 피할 수 없고, 모바일 IP 네트워크에서 이를 해결하기 위해서는 새로운 버퍼관리방식이 요구됨을 보인다.

• 전기의세계
• /
• 제30권11호
• /
• pp.734-746
• /
• 1981

This paper suggests on-load torque measurement for 3 phase induction motors by input -voltage and current utilizing symmetric coordinate analysis technique on the basis of the induction motor equivalent circuit. In this paper, two cases are treated with, i.e, one is the case where the motors' exciting current and primary leakage impedance voltage drop are compensated automatically, adopting the ideal wattmeter whose current coil impedance and voltage coil impedance are 0 and .inf. respectively, and the other is the case where non-ideal wattmeter is adopted and the compensation above is made by computation. As a result of the case study, following conclusions are obtained. 1) By proper combination of the error propagation law and the limit of power consumption, the desirable overall measurement error of the apparatus can be obtained on the basis of the inherent errors of CT and PT. 2) The measurement error is larger in current simulation circuit than in voltage simulation circuit. 3) Between the two cases, the latter is more advantageous than the former from the viewpoint of feasibility and the measurement error. 4) As the attachment of Ammeter in the current simulation circuit influences the measurement error considerably, its internal impedance should be large considerably. 5) The larger the consumption power of the apparatus is, the easier the feasibility is.

• 한국유체기계학회 논문집
• /
• 제10권6호
• /
• pp.17-23
• /
• 2007

In the present work, flow analysis has been performed in the steam turbine bypass control valve (single-path type) for two different cases i.e., case with steam only and case with both steam and water. The numerical analysis is performed by solving three-dimensional Reynolds-averaged Navier-Stokes (RANS) equations. The shear stress transport (SST) model and $k-{\varepsilon}$ model are used to each different case as turbulence closure. Symmetry condition is applied at the mid plane of the valve while adiabatic condition is used at the outer wall of the cage. Grid independency test is performed to find the optimal number of grid points. The pressure and temperature distributions on the outer wall of the cage are analyzed. The mass flow rate at maximum plug opening condition is compared with the designed mass flow rate. The numerical analysis of multiphase mixing flow(liquid and vapor) is also performed to inspect liquid-vapor volume fraction of bypass valve. The result of volume fraction is useful to estimate both the safety and confidence of valve design.

• 한국환경과학회지
• /
• 제16권4호
• /
• pp.449-458
• /
• 2007

Research results for the pressure drop variance depending on operation conditions such as change of inlet concentration, pulse interval, and face velocity, etc., in a pulse air jet-type bag filter show that while at $3kg/cm^2$ whose pulse pressure is low, it is good to make an pulse interval longer in order to form the first layer, it may not be applicable to industry because of a rapid increase in pressure. In addition, the change of inlet concentration contributes more to the increase of pressure drop than the pulse interval does. In order to reduce operation costs by minimizing filter drag of a filter bag at pulse pressure $5kg/cm^2$, the dust concentration should be minimized, and when the inlet dust loading is a lower concentration, the pulse interval in the operation should be less than 70 sec, but when inlet dust loading is a higher concentration, the pulse interval should be below 30 sec. In particular, in the case that inlet dust loading is a higher concentration, a high-pressure distribution is observed regardless of pulse pressure. This is because dust is accumulated continuously in the filter bag and makes it thicker as filtration time increases, and thus the pulse interval should be set to below 30 sec. If the equipment is operated at 1m/min of face velocity, while pressure drop is low, the bag filter becomes larger and thus, its economics are very low due to a large initial investment. Therefore, a face velocity of around 1.5 m/min is considered to be the optimal operation condition. At 1.5 m/min considered to be the most economical face velocity, if the pulse interval increases, since the amount of variation in filter drag is large, depending on the amount of inlet dust loading, the operation may be possible at a lower concentration when the pulse interval is 70 sec. However, for a higher concentration, either face velocity or pulse interval should be reduced.