• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2003.07b
• /
• pp.739-743
• /
• 2003

[ $Ba_2NaNb_5O_{15}$ ], hereafter BNN, thin films are attractive candidates for nonvolatile memory and electro-optic devices. In the present work, thin films that have different contents of Ba, Nb and Na have been prepared by H-MOD technique on silicon and Pt substrates. XRD and SEM were used to investigate the phase evolution behavior and the microstructure of the films. It was found that the films of about 500nm thick were crack-free and uniform in microstructure. Nb content strongly influenced the phase formation of the films, where unwanted phases were always formed at the stoichiometric BNN composition. However, the unwanted phases decreased with the increase of excess Nb content, and the single phase (tetragonal tungsten bronze structure) BNN thin film was obtained when the niobium content reached some point. From this study, the sub-solidus phase diagram below $850^{\circ}C$ for $BaO-Na_2O-Nb_2O_5$ ternary system is proposed.

• Journal of the Korean Society for Heat Treatment
• /
• v.13 no.2
• /
• pp.91-97
• /
• 2000

The structure and mechanical properties of TiN and TiCN thin films deposited on STD61 steel substrates by the RF-sputtering methods has been studied by using XPS, XRD, micro-hardness tester, scratch tester, and wear-resistance tester. XPS results showed that the TiCN thin film formed with chemical bonding state. The TiN thin films grew with (111) orientation having the lowest strain energy by compressive stress, whereas the TiCN thin films grew with both (111) and (200) orientation, but (200) orientation having the lowest surface energy becomes dominant as carbon contents increase. The pre-etching treatment of substrate did not affect on the preferred orientation of thin films, but it played an important role in improving mechanical properties of thin films such as the hardness, adhesion and wear- resistance. Especially, the TiCN thin films showed the superior wear resistances due to high hardness and low friction coefficient compared with TiN thin films.

• Food Science and Preservation
• /
• v.11 no.4
• /
• pp.437-440
• /
• 2004

To investigate the effects of pre-treatment and packaging materials for dried persimmon during 6 month storage, the citric acid, salt, xylitol, L-cystein was pre-treated on dried persimmon, and then packed with LDPE film($0.06\;{\mu}m$) and N/LDPE($0.06\;{\mu}m$). The rate of moisture contents, browning, fungi and weight loss of dried persimmon pre-treated with citric acid, salt, xylitol, L-cystein were changed a little in N/LDPE, but were highly changed in LDPE. The commodity of dried persimmon packed with N/LDPE was also higher than that of LDPE.

• Proceedings of the KIEE Conference
• /
• 1998.07d
• /
• pp.1264-1267
• /
• 1998

$Cu(In_xGa_{1-x})Se_2$ thin films were prepared and characterized with various Ga contents. As the Ga content increased, the grain size of CIGS film became smaller. The 2 $\theta$ values in XRD patterns were shifted to larger values and the overlapped peaks were splitted. The energy bandgap increased from 1.04 to 1.67 eV and the resistivity decreased. The solar cell fabricated with ZnO/CdS/$Cu(In_{0.7}Ga_{0.3})Se_2/Mo$ structure yielded an efficeincy of 14.48% with an acitive area of 0.18 $cm^2$. The efficiency decreased with further increase of Ga content.

• Proceedings of the KIEE Conference
• /
• 2007.07a
• /
• pp.1984-1985
• /
• 2007

Polyimide is widely used as a high-temperature insulating material. Space charge distributions in polyimide (PI) films strongly depend upon electric field, temperature, water content and so on. We observed space charge distributions in PI films with various water contents. When a dc field was applied to as-received PI films or water-treated PI films, positive and negative homo space charges were observed near the respective electrodes at 333 K. In dried PI films, the homo space charges were much reduced, and positive and negative hetero space charges in the bulk were clearly observed. The space charge amounts in water-treated PI films were smaller than in as-received ones, while the current density in water-treated PI film was larger than that in as-received one by two or more orders of magnitude. These suggest not only that the charge injection from the electrode is enhanced by absorbed water but also that absorbed water makes carriers mobile. The decay of space charge was also faster in water-treated PI than in as-received or dried one. This also supports the enhancement of apparent mobilities of carriers in PI by absorbed water.

• Korean Journal of Medicinal Crop Science
• /
• v.23 no.6
• /
• pp.431-438
• /
• 2015

Background : This study was conducted to determine out the effect of storage temperature on the quality of fresh ginseng (Panax ginseng C. A. Meyer) during distribution. Methods and Results : Fresh ginseng was washed, packed in $30{\mu}m$ low density polyethylene (LDPE) film, then stored at 0, -2 and $-4^{\circ}C$. After 4 weeks of storage, ginseng was then stored at $5^{\circ}C$, as a simulation of the distribution process. Ginseng stored at $-4^{\circ}C$ showed higher respiration rate, ethylene production and electrolyte conductivity during the distribution phase than those stored at 0 and $-2^{\circ}C$. Decay and browning rate rapidly increased following 3 weeks of distribution in samples stored $-4^{\circ}C$. However ginseng stored $-2^{\circ}C$, which is below freezing point, for 4 weeks did not show the physiological change or quality deterioration. Ginsenoside contents decreased during storage for all plant, but did not differ significantly between storage temperatures. Conclusions : Storage at temperatures below $-2^{\circ}C$ can negatively affect respiratory characteristics and electrolyte leakage and increase quality deterioration and decay rates during distribution.

• Journal of Surface Science and Engineering
• /
• v.43 no.6
• /
• pp.266-271
• /
• 2010

Ternary Mo-Cu-N films were deposited on Si wafer substrates with various copper contents by magnetron sputtering method using Mo target and Cu target in $Ar/N_2$ gaseous atmosphere. As increasing $N_2$ pressure, the microstructure of Mo-N films changed from ${\gamma}-Mo_2N$ of (111) having face-centered-cubic (FCC) structure to $\delta$-MoN of (200) having hexagonal structure. Detailed the microstructures of the Mo-Cu-N coatings were studied by X-ray diffraction, scanning electron microscopy and field emission transmission electron microscope. The results indicated that the incorporation of copper into the growing Mo-N coating led to the $Mo_2N$ and MoN crystallites were more well-distributed and refined and the copper existed in grain boundary. Ternary Mo-Cu-N films had a composite microstructure of the nanosized crystal crystalline ${\gamma}-Mo_2N$ and $\delta$-MoN surrounded by amorphous $Cu_3N$ phase.

• Journal of Surface Science and Engineering
• /
• v.29 no.6
• /
• pp.829-833
• /
• 1996

Superconducting YBaCuO thin films were deposited on MgO (100) single crystal substrate by rf reactive sputtering method. Sputtering target was prepared by mixing the original powders of $Y_2O_3$, $BaCO_3$, and CuO at $830^{\circ}C$, and its composition was $YBa_2Cu_{3.3}O_x$ adding the excess CuO to compensate for the loss of Cu in the deposition process. The sputtering conditions for a high quality of YBCO thin film were: substrate temperature of 13$0^{\circ}C$; gas pressure of 10 mTorr; gas mixture ($O_2$: Ar =10: 90); distance of 2.5 inch; and rf power density of 4.87 W /$\textrm{cm}^2$. The deposition rate was 2.4~2.6 nm/min. From the RBS results, it was found that Cu and Ba contents in thin films decreased with the increase of substrate temperature. The increase of gas pressure resulted in significant deficiency of Ba elements.

• Journal of Powder Materials
• /
• v.9 no.4
• /
• pp.227-234
• /
• 2002

For the austenitic stainless steel (304L) manufactured by metal injection molding(MIM), the effects of copper content and sintering temperature on the mechanical properties, antibacterial activities, corrosion resistance, and electric resistances were investigated. The specimens were prepared by injection molding of the premixed powders of water-atomized 304 L and Cu with poly-acetyl binders. The green compacts were prepared with various copper contents from 0 to 10 wt.% Cu, which were debound thermally at 873 K for 7.2 ks in $N_2$gas atmosphere and subsequently sintered at various temperatures from 1323 K to 1623 K for 7.2 ks in Ar gas atmosphere. The relative density and tensile strength of the sintered compacts showed the minimum values at 5 and 8 wt.% Cu, respectively. Both the relative density and the tensile strength of the specimen with 10 wt.% Cu sintered at 1373 K showed the highest values, higher than those of copper-free specimen. Antibacterial activities investigated by the plastic film contact printing method for bacilli and the quantitative analysis of copper ion dissolved in water increased as the increase of the copper content to stainless steels. It was also verified by the measurement of pitting potential that the copper addition in 304 L could improve the corrosion resistance. Furthermore the electric conductivity increased with the increase of copper content.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.25 no.10
• /
• pp.811-816
• /
• 2012

The effect of co-sputtering condition on the structural properties of $Mg_xZn_{1-x}O$ thin films grown by RF magnetron co-sputtering system was investigated for manufacturing ZnO/MgZnO structure LED. $Mg_xZn_{1-x}O$ thin films were grown with ZnO and MgO target varying RF power. Structural properties were investigated by X-ray diffraction (XRD) and Energy dispersive spectroscopy (EDS). The ZnO thin films have sufficient crystallinity on the high RF power. As RF power of ZnO target increased, the contents of MgO in the $Mg_xZn_{1-x}O$ film decreased. LED was manufactured using ZnO/MgZnO multi-layer on p-GaN/$Al_2O_3$ substrate. Threshold voltage of multi-layer LED was appeared at 8 V, and it was luminesced at wave length of 550 nm.